On a decoder instance, after the profile has been parsed from the stream
__v4l2_ctrl_s_ctrl() is called to notify userspace about changes in the
read-only profile control. This ends up calling back into the CODA driver
where a missing check on the s_ctrl caused the profile information that has
just been parsed from the stream to be overwritten with the default
baseline profile.
Later on the driver fails to enable frame reordering, based on the wrong
profile information.
Fixes: 347de126d1da (media: coda: add read-only h.264 decoder
profile/level controls)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
of_node_put has taken the null pointer check into account. So it is
safe to remove the duplicated check before of_node_put.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
The CODA7541 firmware does not set the SPS frame cropping fields to
properly describe coded h.264 streams with frame sizes that are not a
multiple of the macroblock size.
This adds RBSP parsing code and a SPS fixup routine to manually replace
the cropping information in the headers produced by the firmware with
the correct values.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[hans.verkuil@cisco.com: added explanation of SPS RBSP to comment]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When encoding h.264, if visible resolution is not aligned to macroblock
size, frame cropping has to be set in the SPS header to produce correct
streams. The CODA960 firmware can do this on its own if asked to.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This enables reordering support for h.264 main profile level 4.2,
5.0, and 5.1 streams. Even though we likely can't play back such
streams at full speed, we should still recognize them correctly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Allow to set a crop rectangle on the encoder output queue to set the
visible resolution as required by the V4L2 codec API.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the i.MX6 CODA960 firmware versions 2.1.9
(revision 32515) to the list of supported firmware versions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Explicitly clear DEC_SEQ_JPG_THUMB_EN during sequence initialization.
Not clearing the register does not cause problems, since the only other
codec (MPEG-4 decode) that writes to this register happens to always
write 0 as well.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Padding the bitstream buffer is not enough to reliably avoid prefetch
failures. Picture runs with the next buffer's header already visible to
the CODA7541 succeed much more reliably, so always queue two JPEG frames
into the bitstream buffer.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The hardware codec is not colorspace aware. We should trust userspace to
set the correct colorimetry information on the OUTPUT queue and mirror
the exact same setting on the CAPTURE queue.
There is no reason to restrict colorspace to JPEG for JPEG images, if
userspace injects the correct colorspace information into the JPEG
headers after encoding.
Fixes: b14ac54568 ("[media] coda: improve colorimetry handling")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If new buffers are queued after streamoff, the flag will be cleared
anyway, so this is mostly for the purpose of correctness.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Whether reordering should be enabled only depends on the h.264 profile.
Stop parsing the level and drop the debug message, profile and level
can now be determined via read-only decoder controls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The decoder profile/level controls initially can be used to determine
supported profiles and levels. The values are set for a given stream
once the headers are parsed.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The encoder picture run command takes a picture source stride parameter.
This must be set to the output queue's bytesperline, not width.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit f1a81afc98 ("[media] m2m: fix bad unlock balance")
removed the last use of v4l2_m2m_ops.lock and
v4l2_m2m_ops.unlock hooks. They are not actually
used anymore. Remove them.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Do not set context colorimetry on the raw (OUTPUT) queue for encoders.
Always set colorimetry on the coded queue (CAPTURE for encoders, OUTPUT
for decoders).
This also skips propagation of capture queue format and selection
rectangle on S_FMT(OUTPUT) to the CAPTURE queue for encoders.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver helpfully resets the capture queue format and selection
rectangle whenever output format is changed. This only works while
the capture queue is not busy.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of duplicating the same code, call into coda_s_fmt_vid_out to
propagate the output format to the capture queue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
While the h.264 standard only allows up to 16 reference frames, the CODA
firmware needs two more buffers: one to hold the currently decoded frame
and one for the display frame. Adding the framebuffer needed by the
driver for VDOA operation brings the total to a maximum of 19 internal
framebuffers.
Lift the current maximum of 17 internal framebuffers to allow playback
of high profile streams that require more than 14 reference frames.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for the CodaHx4 VPU used on i.MX51.
Decoding h.264, MPEG-4, and MPEG-2 video works, as well as encoding
h.264. MPEG-4 encoding is not enabled, it currently produces visual
artifacts.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix (bogus) sparse warning about uninited me_bits]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Lucas Stach
zhong jiang
Mauro Carvalho Chehab
Linus Torvalds
Philipp Zabel
Randy Dunlap
Ezequiel Garcia