We need to change the capacity in all nodes after one node
finishs reshape. And as we did before, we can't change the
capacity directly in md_do_sync, instead, the capacity should
be only changed in update_size or received CHANGE_CAPACITY
msg.
So master node calls update_size after completes reshape in
md_reap_sync_thread, but we need to skip ops->update_size if
MD_CLOSING is set since reshaping could not be finish.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Since the resync region from suspend_info means one node
is reshaping this area, so the position of reshape_progress
should be included in the area.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
For clustered raid10 scenario, we need to let all the nodes
know about that a new disk is added to the array, and the
reshape caused by add new member just need to be happened in
one node, but other nodes should know about the change.
Since reshape means read data from somewhere (which is already
used by array) and write data to unused region. Obviously, it
is awful if one node is reading data from address while another
node is writing to the same address. Considering we have
implemented suspend writes in the resyncing area, so we can
just broadcast the reading address to other nodes to avoid the
trouble.
For master node, it would call reshape_request then update sb
during the reshape period. To avoid above trouble, we call
resync_info_update to send RESYNC message in reshape_request.
Then from slave node's view, it receives two type messages:
1. RESYNCING message
Slave node add the address (where master node reading data from)
to suspend list.
2. METADATA_UPDATED message
Once slave nodes know the reshaping is started in master node,
it is time to update reshape position and call start_reshape to
follow master node's step. After reshape is done, only reshape
position is need to be updated, so the majority task of reshaping
is happened on the master node.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
To support add disk under grow mode, we need to resize
all the bitmaps of each node before reshape, so that we
can ensure all nodes have the same view of the bitmap of
the clustered raid.
So after the master node resized the bitmap, it broadcast
a message to other slave nodes, and it checks the size of
each bitmap are same or not by compare pages. We can only
continue the reshaping after all nodes update the bitmap
to the same size (by checking the pages), otherwise revert
bitmap size to previous value.
The resize_bitmaps interface and BITMAP_RESIZE message are
introduced in md-cluster.c for the purpose.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
In copy_params(), the struct 'dm_ioctl' is first copied from the user
space buffer 'user' to 'param_kernel' and the field 'data_size' is
checked against 'minimum_data_size' (size of 'struct dm_ioctl' payload
up to its 'data' member). If the check fails, an error code EINVAL will be
returned. Otherwise, param_kernel->data_size is used to do a second copy,
which copies from the same user-space buffer to 'dmi'. After the second
copy, only 'dmi->data_size' is checked against 'param_kernel->data_size'.
Given that the buffer 'user' resides in the user space, a malicious
user-space process can race to change the content in the buffer between
the two copies. This way, the attacker can inject inconsistent data
into 'dmi' (versus previously validated 'param_kernel').
Fix redundant copying of 'minimum_data_size' from user-space buffer by
using the first copy stored in 'param_kernel'. Also remove the
'data_size' check after the second copy because it is now unnecessary.
Cc: stable@vger.kernel.org
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
WARN_ON() already contains an unlikely(), so it's not necessary to
wrap it into another.
Signed-off-by: Igor Stoppa <igor.stoppa@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The API surrounding refcount_t should be used in place of atomic_t
when variables are being used as reference counters. This API can
prevent issues such as counter overflows and use-after-free
conditions. Within the dm zoned target stack, the atomic_t API is
used for bioctx->ref and cw->refcount. Change these to use
refcount_t, avoiding the issues mentioned.
Signed-off-by: John Pittman <jpittman@redhat.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The API surrounding refcount_t should be used in place of atomic_t
when variables are being used as reference counters. It can
potentially prevent reference counter overflows and use-after-free
conditions. In the dm thin layer, one such example is tc->refcount.
Change this from the atomic_t API to the refcount_t API to prevent
mentioned conditions.
Signed-off-by: John Pittman <jpittman@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Now that request-based DM (multipath) is blk-mq only: this restriction
is required while the legacy request-based IO path still exists.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Kees writes:
"Fix open-coded multiplication arguments to allocators
- Fixes several new open-coded multiplications added in the 4.19
merge window."
* tag 'alloc-args-v4.19-rc8' of https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Replace more open-coded allocation size multiplications
Now that request-based DM is only using blk-mq, there is no need to
differentiate between legacy "rq" and new "mq". We're back to a single
request-based DM -- and there was much rejoicing!
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm supports both, and since we're killing off the legacy path in
general, get rid of it in dm.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The dm-linear target is independent of the dm-zoned target. For code
requiring support for zoned block devices, use CONFIG_BLK_DEV_ZONED
instead of CONFIG_DM_ZONED.
While at it, similarly to dm linear, also enable the DM_TARGET_ZONED_HM
feature in dm-flakey only if CONFIG_BLK_DEV_ZONED is defined.
Fixes: beb9caac21 ("dm linear: eliminate linear_end_io call if CONFIG_DM_ZONED disabled")
Fixes: 0be12c1c7f ("dm linear: add support for zoned block devices")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
After 9e1cc0a545 ("md: use mddev_suspend/resume instead of ->quiesce()")
We still have similar left in bitmap functions.
Replace quiesce() with mddev_suspend/resume.
Also move md_bitmap_create out of mddev_suspend. and move mddev_resume
after md_bitmap_destroy. as we did in set_bitmap_file.
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Gioh Kim <gi-oh.kim@profitbricks.com>
Signed-off-by: Shaohua Li <shli@fb.com>
And earlier commit removed the error label to two statements that
are now never reachable. Since this code is now dead code, remove it.
Detected by CoverityScan, CID#1462409 ("Structurally dead code")
Fixes: d5d885fd51 ("md: introduce new personality funciton start()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shaohua Li <shli@fb.com>
It is best to avoid any extra overhead associated with bio completion.
DM core will indirectly call a DM target's .end_io if it is defined.
In the case of DM linear, there is no need to do so (for every bio that
completes) if CONFIG_DM_ZONED is not enabled.
Avoiding an extra indirect call for every bio completion is very
important for ensuring DM linear doesn't incur more overhead that
further widens the performance gap between dm-linear and raw block
devices.
Fixes: 0be12c1c7f ("dm linear: add support for zoned block devices")
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If dm-linear or dm-flakey are layered on top of a partition of a zoned
block device, remapping of the start sector and write pointer position
of the zones reported by a report zones BIO must be modified to account
for the target table entry mapping (start offset within the device and
entry mapping with the dm device). If the target's backing device is a
partition of a whole disk, the start sector on the physical device of
the partition must also be accounted for when modifying the zone
information. However, dm_remap_zone_report() was not considering this
last case, resulting in incorrect zone information remapping with
targets using disk partitions.
Fix this by calculating the target backing device start sector using
the position of the completed report zones BIO and the unchanged
position and size of the original report zone BIO. With this value
calculated, the start sector and write pointer position of the target
zones can be correctly remapped.
Fixes: 10999307c1 ("dm: introduce dm_remap_zone_report()")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit 7e6358d244 ("dm: fix various targets to dm_register_target
after module __init resources created") inadvertently introduced this
bug when it moved dm_register_target() after the call to KMEM_CACHE().
Fixes: 7e6358d244 ("dm: fix various targets to dm_register_target after module __init resources created")
Cc: stable@vger.kernel.org
Signed-off-by: Shenghui Wang <shhuiw@foxmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
when the nbuckets of cache device is smaller than 1024, making cache
device will trigger BUG_ON in kernel, add a condition to avoid this.
Reported-by: nitroxis <n@nxs.re>
Signed-off-by: Dongbo Cao <cdbdyx@163.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Split the combined '||' statements in if() check, to make the code easier
for debug.
Signed-off-by: Dongbo Cao <cdbdyx@163.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Current cache_set has MAX_CACHES_PER_SET caches most, and the macro
is used for
"
struct cache *cache_by_alloc[MAX_CACHES_PER_SET];
"
in the define of struct cache_set.
Use MAX_CACHES_PER_SET instead of magic number 8 in
__bch_bucket_alloc_set.
Signed-off-by: Shenghui Wang <shhuiw@foxmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In extents.c:bch_extent_bad(), number 96 is used as parameter to call
btree_bug_on(). The purpose is to check whether stale gen value exceeds
BUCKET_GC_GEN_MAX, so it is better to use macro BUCKET_GC_GEN_MAX to
make the code more understandable.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Guoqing Jiang
Michał Mirosław
Wenwen Wang
Igor Stoppa
John Pittman
Shaohua Li
Mike Snitzer
Greg Kroah-Hartman
Jens Axboe
Damien Le Moal
Jack Wang
Colin Ian King
Shenghui Wang
Dongbo Cao
Coly Li