Pull input updates from Dmitry Torokhov:
- a new driver for Rohm BU21029 touch controller
- new bitmap APIs: bitmap_alloc, bitmap_zalloc and bitmap_free
- updates to Atmel, eeti. pxrc and iforce drivers
- assorted driver cleanups and fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
MAINTAINERS: Add PhoenixRC Flight Controller Adapter
Input: do not use WARN() in input_alloc_absinfo()
Input: mark expected switch fall-throughs
Input: raydium_i2c_ts - use true and false for boolean values
Input: evdev - switch to bitmap API
Input: gpio-keys - switch to bitmap_zalloc()
Input: elan_i2c_smbus - cast sizeof to int for comparison
bitmap: Add bitmap_alloc(), bitmap_zalloc() and bitmap_free()
md: Avoid namespace collision with bitmap API
dm: Avoid namespace collision with bitmap API
Input: pm8941-pwrkey - add resin entry
Input: pm8941-pwrkey - abstract register offsets and event code
Input: iforce - reorganize joystick configuration lists
Input: atmel_mxt_ts - move completion to after config crc is updated
Input: atmel_mxt_ts - don't report zero pressure from T9
Input: atmel_mxt_ts - zero terminate config firmware file
Input: atmel_mxt_ts - refactor config update code to add context struct
Input: atmel_mxt_ts - config CRC may start at T71
Input: atmel_mxt_ts - remove unnecessary debug on ENOMEM
Input: atmel_mxt_ts - remove duplicate setup of ABS_MT_PRESSURE
...
This adds a generic resistive touchscreen (GRTS) driver, which is based
on an IIO device (an ADC). It must be connected to the channels of an ADC
to receive touch data. Then it will feed the data into the input subsystem
where it registers an input device.
It uses an IIO callback buffer to register to the IIO device
Some parts of this patch are based on initial original work by
Mohamed Jamsheeth Hajanajubudeen and Bandaru Venkateswara Swamy
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ChipOne icn8505 is an i2c capacitive touchscreen controller typically
used in cheap x86 tablets, this commit adds a driver for it.
Note the icn8505 is somewhat similar to the icn8318 and I started with
modifying that driver to support both, but in the end the differences were
too large and I decided to write a new driver instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since AVR32 arch is gone, atmel-wm97xx driver is useless. In theory it
could have been rewritten to work with AT91 devices, but the driver is from
the platform data era, and a bit hard coded to work on AVR32 hardware
variant of the AC97C peripheral, so let's remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- three new touchscreen drivers: EETI EXC3000, HiDeep, and Samsung
S6SY761
- the timer API conversion (setup_timer() -> timer_setup())
- a few drivers swiytched to using managed API for creating custom
device attributes
- other assorted fixed and cleanups.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (50 commits)
Input: gamecon - mark expected switch fall-throughs
Input: sidewinder - mark expected switch fall-throughs
Input: spaceball - mark expected switch fall-throughs
Input: uinput - unlock on allocation failure in ioctl
Input: add support for the Samsung S6SY761 touchscreen
Input: add support for HiDeep touchscreen
Input: st1232 - remove obsolete platform device support
Input: convert autorepeat timer to use timer_setup()
media: ttpci: remove autorepeat handling and use timer_setup
Input: cyttsp4 - avoid overflows when calculating memory sizes
Input: mxs-lradc - remove redundant assignment to pointer input
Input: add I2C attached EETI EXC3000 multi touch driver
Input: goodix - support gt1151 touchpanel
Input: ps2-gpio - actually abort probe when connected to sleeping GPIOs
Input: hil_mlc - convert to using timer_setup()
Input: hp_sdc - convert to using timer_setup()
Input: touchsceen - convert timers to use timer_setup()
Input: keyboard - convert timers to use timer_setup()
Input: uinput - fold header into the driver proper
Input: uinput - remove uinput_allocate_device()
...
The S6SY761 touchscreen is a capicitive multi-touch controller
for mobile use. It's connected with i2c at the address 0x48.
This commit provides a basic version of the driver which can
handle only initialization, touch events and power states.
The controller is controlled by a firmware which, in the version
I currently have, doesn't provide all the possible
functionalities mentioned in the datasheet.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The HiDeep touchscreen device is a capacitive multi-touch controller
mainly for multi-touch supported devices use. It use I2C interface for
communication to IC and provide axis X, Y, Z locations for ten finger
touch through input event interface to userspace.
It support the Crimson and the Lime two type IC. They are different
the number of channel supported and FW size. But the working protocol
is same.
Signed-off-by: Anthony Kim <anthony.kim@hideep.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The 3000 series have a new protocol which allows to report up to 5 points
in a single 66 byte frame. One must always read in 66 byte frames.
To support up to 10 points, two consecutive frames need to be read:
The first frame says how many points until sync.
The second frame must say zero points or both frames must be discarded.
To be able to work with the higher 400KHz I2C bus rate, one must
successfully send a special package prior _each_ read or the controller
will refuse to cooperate.
This is a minimal implementation based on egalax_i2c.c (which can be found
on the internet) and egalax_ts.c but without the vendor interface and no
power management support.
Signed-off-by: Ahmet Inan <inan@distec.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change control of TOUCHSCREEN_USB_EASYTOUCH prompt string from
EMBEDDED to EXPERT to match the rest of this Kconfig file.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for the new AC97 bus code, which discovers the devices
rather than uses platform data.
As part of this discovery, it enables a multi-function device wm97xx,
which supports touchscreen, battery, ADC and an audio codec. This patch
adds the code to bind the touchscreen "cell" as the touchscreen driver.
This was tested on the pxa architecture with a pxa270 + wm9713 + the
mioa701 touchscreen.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stmfts (ST-Microelectronics FingerTip S) touchscreen device is a
capacitive multi-touch controller mainly for mobile use. It's connected
through i2c bus at the address 0x49 and it interfaces with userspace
through input event interface.
At the current state it provides a touchscreen multitouch functionality up
to 10 fingers. Each finger is enumerated with a distinctive id (from 0 to
9).
If enabled the device can support single "touch" hovering, by providing
three coordinates, x, y and distance.
It is possible to select the touchkey functionality which provides a basic
two keys interface for "home" and "back" menu, typical in mobile phones.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
- a big update from Mauro converting input documentation to ReST format
- Synaptics PS/2 is now aware of SMBus companion devices, which means
that we can now use native RMI4 protocol to handle touchpads, instead
of relying on legacy PS/2 mode.
- we removed support from BMA180 accelerometer from input devices as it
is now handled properly by IIO
- update to TSC2007 to corretcly report pressure
- other miscellaneous driver fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (152 commits)
Input: ar1021_i2c - use BIT to check for a bit
Input: twl4030-pwrbutton - use input_set_capability() helper
Input: twl4030-pwrbutton - use correct device for irq request
Input: ar1021_i2c - enable touch mode during open
Input: add uinput documentation
dt-bindings: input: add bindings document for ar1021_i2c driver
dt-bindings: input: rotary-encoder: fix typo
Input: xen-kbdfront - add module parameter for setting resolution
ARM: pxa/raumfeld: fix compile error in rotary controller resources
Input: xpad - do not suggest writing to Dominic
Input: xpad - don't use literal blocks inside footnotes
Input: xpad - note that usb/devices is now at /sys/kernel/debug/
Input: docs - freshen up introduction
Input: docs - split input docs into kernel- and user-facing
Input: docs - note that MT-A protocol is obsolete
Input: docs - update joystick documentation a bit
Input: docs - remove disclaimer/GPL notice
Input: fix "Game console" heading level in joystick documentation
Input: rotary-encoder - remove references to platform data from docs
Input: move documentation for Amiga CD32
...
The tsc2007 chip not only has a resistive touch screen controller but
also an external AUX adc imput which can be used for an ambient
light sensor, battery voltage monitoring or any general purpose.
Additionally it can measure the chip temperature.
This extension provides an iio interface for these adc channels.
Since it is not wasting much resources and is very straightforward,
we simply provide all other adc channels as optional iio interfaces
as weel. This can be used for debugging or special applications.
This patch also splits the tsc2007 driver in several source files:
tsc2007.h -- constants, structs and stubs
tsc2007_core.c -- functional parts of the original driver
tsc2007_iio.c -- the optional iio stuff
Makefile magic allows to conditionally link the iio stuff
if CONFIG_IIO=y or =m in a way that it works with
CONFIG_TOUCHSCREEN_TSC2007=m.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a basic driver for the Zeitec ZET6223 I2C touchscreen
controllers. The driver does not support firmware loading, which is not
required for all tablets which contain this chip.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Linus Torvalds
Zhu Yi
Eugen Hristev
Dmitry Torokhov
Hans de Goede
Masanari Iida
Corentin Labbe
Andi Shyti
Anthony Kim
Ahmet Inan
Randy Dunlap
Robert Jarzmik
Martin Kepplinger
Ksenija Stanojevic
H. Nikolaus Schaller
Jelle van der Waa
Andy Shevchenko