The CEC_TX_STATUS_MAX_RETRIES should be set for errors only to
prevent the CEC framework from retrying the transmit. If the
transmit was successful, then don't set this flag.
Found by running 'cec-compliance -A' on a beaglebone box.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Currently the check to see if the timeout has reached zero is incorrect
and the check is instead checking if the timeout is non-zero and not
zero, hence it will break out of the loop on the first iteration and
the msleep is never executed. Fix this by breaking from the loop when
timeout is zero.
Detected by CoverityScan, CID#1469404 ("Logically Dead Code")
Fixes: f0316f9389 ("drm/i2c: tda9950: add CEC driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Pull VLA removal leftovers from Kees Cook:
- bus/imx-weim: Use maximum register count to avoid VLA
- drm/i2c/tda9950: Use maximum CEC message size to avoid VLA
* tag 'vla-leftovers-v4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
bus: imx-weim: Remove VLA usage
drm/i2c: tda9950: Remove VLA usage
From: Russell King <rmk@armlinux.org.uk>
As per the patches posted, discussed and tested by Peter Rosin, this
converts TDA998x to a bridge driver, while still allowing Armada and
TI LCDC to continue using it as they always have done. It also gets
rid of the private .fill_modes function, and tweaks the TMDS divider
calculation to be more correct to the available information.
[airlied: fixed two conflicts]
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180802093421.GA29670@rmk-PC.armlinux.org.uk
The serializer PLL divider is a power-of-two divider, so our calculation
which assumes that it's a numerical divider is incorrect. Replace it
with one that results in a power-of-two divider value instead.
Tested with all supported modes with a Samsung S24C750.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
We can achieve the same effect via the get_modes() method, rather than
wrapping the fill_modes helper.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Move the mode_valid() implementation to the bridge instead of the
connector, as we're checking the bridge's capabilities.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Register the bridge outside of the component helper as we have
drivers that wish to use the tda998x without its encoder.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cleanup the code a little from the effects of the previous changes:
- Move tda998x_destroy() to be above tda998x_create()
- Use 'dev' directly in tda998x_create() where appropriate.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Move the tda998x_priv allocation inside tda998x_create() and simplify
the tda998x_create()'s arguments. Pass the same to tda998x_destroy().
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Convert tda998x to a bridge driver with built-in encoder support for
compatibility with existing component drivers.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Move the non-DT configuration of the TDA998x into tda998x_create()
so that we do all setup in one place.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This fits better with the drm_bridge callbacks for when this
driver becomes a drm_bridge.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
[edited by rmk to just split the tda998x_encoder_dpms() function
and restore the double-disable protection we originally had,
preserving original behaviour.]
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
We got a few conflicts in drm_atomic.c after merging the DRM writeback support,
now we need a backmerge to unlock develop development on drm-misc-next.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
The TDA998x is a HDMI transmitter with a TDA9950 CEC engine integrated
onto the same die. Add support for the TDA9950 CEC engine to the
TDA998x driver.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Add a CEC driver for the TDA9950, which is a stand-alone I2C CEC device,
but is also integrated into HDMI transceivers such as the TDA9989 and
TDA19989.
The TDA9950 contains a command processor which handles retransmissions
and the low level bus protocol. The driver just has to read and write
the messages, and handle error conditions.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Always disable and clear interrupts at probe time to ensure that the
TDA998x is in a sane state. This ensures that the interrupt line,
which is also the CEC clock calibration signal, is always deasserted.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Dave Airlie
Hans Verkuil
Colin Ian King
Linus Torvalds
Kees Cook
Russell King
Peter Rosin
Daniel Vetter
Gustavo Padovan
Laura Abbott
Luc Van Oostenryck