The maximum unicast datagram size /without/ link fragmentation is
4096 - 4 = 4092 (max IEEE 1394 async payload size at >= S800 bus speed,
minus unfragmented encapssulation header). Max broadcast datagram size
without fragmentation is 8 bytes less than that (due to GASP header).
The maximum datagram size /with/ link fragmentation is 0xfff = 4095
for unicast and broadcast. This is because the RFC 2734 fragment
encapsulation header field for datagram size is only 12 bits wide.
Fixes: 5d48f00d836a('firewire: net: fix maximum possible MTU')
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
firewire-net, like the older eth1394 driver, reduced the initial MTU to
less than 1500 octets if the local link layer controller's asynchronous
packet reception limit was lower.
This is bogus, since this reception limit does not have anything to do
with the transmission limit. Neither did this reduction affect the TX
path positively, nor could it prevent link fragmentation at the RX path.
Many FireWire CardBus cards have a max_rec of 9, causing an initial MTU
of 1024 - 16 = 1008. RFC 2734 and RFC 3146 allow a minimum max_rec = 8,
which would result in an initial MTU of 512 - 16 = 496. On such cards,
IPv6 could only be employed if the MTU was manually increased to 1280 or
more, i.e. IPv6 would not work without intervention from userland.
We now always initialize the MTU to 1500, which is the default according
to RFC 2734 and RFC 3146.
On a VIA VT6316 based CardBus card which was affected by this, changing
the MTU from 1008 to 1500 also increases TX bandwidth by 6 %.
RX remains unaffected.
CC: netdev@vger.kernel.org
CC: linux1394-devel@lists.sourceforge.net
CC: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b3e3893e12 ("net: use core MTU range checking in misc drivers")
mistakenly introduced an upper limit for firewire-net's MTU based on the
local link layer controller's reception capability. Revert this. Neither
RFC 2734 nor our implementation impose any particular upper limit.
Actually, to be on the safe side and to make the code explicit, set
ETH_MAX_MTU = 65535 as upper limit now.
(I replaced sizeof(struct rfc2734_header) by the equivalent
RFC2374_FRAG_HDR_SIZE in order to avoid distracting long/int conversions.)
Fixes: b3e3893e1253('net: use core MTU range checking in misc drivers')
CC: netdev@vger.kernel.org
CC: linux1394-devel@lists.sourceforge.net
CC: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
firewire-net:
- set min/max_mtu
- remove fwnet_change_mtu
nes:
- set max_mtu
- clean up nes_netdev_change_mtu
xpnet:
- set min/max_mtu
- remove xpnet_dev_change_mtu
hippi:
- set min/max_mtu
- remove hippi_change_mtu
batman-adv:
- set max_mtu
- remove batadv_interface_change_mtu
- initialization is a little async, not 100% certain that max_mtu is set
in the optimal place, don't have hardware to test with
rionet:
- set min/max_mtu
- remove rionet_change_mtu
slip:
- set min/max_mtu
- streamline sl_change_mtu
um/net_kern:
- remove pointless ndo_change_mtu
hsi/clients/ssi_protocol:
- use core MTU range checking
- remove now redundant ssip_pn_set_mtu
ipoib:
- set a default max MTU value
- Note: ipoib's actual max MTU can vary, depending on if the device is in
connected mode or not, so we'll just set the max_mtu value to the max
possible, and let the ndo_change_mtu function continue to validate any new
MTU change requests with checks for CM or not. Note that ipoib has no
min_mtu set, and thus, the network core's mtu > 0 check is the only lower
bounds here.
mptlan:
- use net core MTU range checking
- remove now redundant mpt_lan_change_mtu
fddi:
- min_mtu = 21, max_mtu = 4470
- remove now redundant fddi_change_mtu (including export)
fjes:
- min_mtu = 8192, max_mtu = 65536
- The max_mtu value is actually one over IP_MAX_MTU here, but the idea is to
get past the core net MTU range checks so fjes_change_mtu can validate a
new MTU against what it supports (see fjes_support_mtu in fjes_hw.c)
hsr:
- min_mtu = 0 (calls ether_setup, max_mtu is 1500)
f_phonet:
- min_mtu = 6, max_mtu = 65541
u_ether:
- min_mtu = 14, max_mtu = 15412
phonet/pep-gprs:
- min_mtu = 576, max_mtu = 65530
- remove redundant gprs_set_mtu
CC: netdev@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: Stefan Richter <stefanr@s5r6.in-berlin.de>
CC: Faisal Latif <faisal.latif@intel.com>
CC: linux-rdma@vger.kernel.org
CC: Cliff Whickman <cpw@sgi.com>
CC: Robin Holt <robinmholt@gmail.com>
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Marek Lindner <mareklindner@neomailbox.ch>
CC: Simon Wunderlich <sw@simonwunderlich.de>
CC: Antonio Quartulli <a@unstable.cc>
CC: Sathya Prakash <sathya.prakash@broadcom.com>
CC: Chaitra P B <chaitra.basappa@broadcom.com>
CC: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
CC: MPT-FusionLinux.pdl@broadcom.com
CC: Sebastian Reichel <sre@kernel.org>
CC: Felipe Balbi <balbi@kernel.org>
CC: Arvid Brodin <arvid.brodin@alten.se>
CC: Remi Denis-Courmont <courmisch@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no check if ioremap_nocache() returns a valid pointer.
Potentially it can lead to null pointer dereference.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (renamed goto labels)
Pull firewire leftover from Stefan Richter:
"Occurrences of timeval were supposed to be eliminated last round, now
remove a last forgotten one"
* tag 'firewire-update2' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: nosy: Replace timeval with timespec64
Firewire was using is_compat_task to check whether it was in a compat
ioctl or a non-compat ioctl. Use is_compat_syscall instead so it works
properly on all architectures.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'struct timeval' uses a 32 bit field for its 'seconds' value which
will overflow in year 2038 and beyond. This patch replaces the use
of timeval in nosy.c with timespec64 which doesn't suffer from y2038
issue. The code is correct as is - since it is only using the
microseconds portion of timeval. However, this patch does the
replacement as part of a larger effort to remove all instances of
'struct timeval' from the kernel (that would help identify cases
where the code is actually broken).
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Pull firewire updates from Stefan Richter:
"IEEE 1394 subsystem patches:
- move away from outmoded timekeeping API
- error reporting fix
- documentation bits"
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ABI documentation: libhinawa uses firewire-cdev
firewire: ABI documentation: jujuutils were renamed to linux-firewire-utils
firewire: ohci: propagate return code from soft_reset to probe and resume
firewire: nosy: Replace timeval with timespec64
Pull firewire fix from Stefan Richter:
"Work around JMicron initialization quirk, which ffected isochronous
transmission, e.g. audio via FFADO or ALSA"
* tag 'firewire-update' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: fix JMicron JMB38x IT context discovery
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
software_reset() may fail
- due to unresponsive chip with -EBUSY (-16), or
- due to ejected or unseated card with -ENODEV (-19).
Let the PCI probe and resume routines log the actual error code instead
of hardwired -EBUSY.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
32 bit systems using 'struct timeval' will break in the year 2038, so
we replace the code appropriately. However, this driver is not broken
in 2038 since we are using only the microseconds portion of the
current time.
This patch replaces timeval with timespec64.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Reported by Clifford and Craig for JMicron OHCI-1394 + SDHCI combo
controllers: Often or even most of the time, the controller is
initialized with the message "added OHCI v1.10 device as card 0, 4 IR +
0 IT contexts, quirks 0x10". With 0 isochronous transmit DMA contexts
(IT contexts), applications like audio output are impossible.
However, OHCI-1394 demands that at least 4 IT contexts are implemented
by the link layer controller, and indeed JMicron JMB38x do implement
four of them. Only their IsoXmitIntMask register is unreliable at early
access.
With my own JMB381 single function controller I found:
- I can reproduce the problem with a lower probability than Craig's.
- If I put a loop around the section which clears and reads
IsoXmitIntMask, then either the first or the second attempt will
return the correct initial mask of 0x0000000f. I never encountered
a case of needing more than a second attempt.
- Consequently, if I put a dummy reg_read(...IsoXmitIntMaskSet)
before the first write, the subsequent read will return the correct
result.
- If I merely ignore a wrong read result and force the known real
result, later isochronous transmit DMA usage works just fine.
So let's just fix this chip bug up by the latter method. Tested with
JMB381 on kernel 3.13 and 4.3.
Since OHCI-1394 generally requires 4 IT contexts at a minium, this
workaround is simply applied whenever the initial read of IsoXmitIntMask
returns 0, regardless whether it's a JMicron chip or not. I never heard
of this issue together with any other chip though.
I am not 100% sure that this fix works on the OHCI-1394 part of JMB380
and JMB388 combo controllers exactly the same as on the JMB381 single-
function controller, but so far I haven't had a chance to let an owner
of a combo chip run a patched kernel.
Strangely enough, IsoRecvIntMask is always reported correctly, even
though it is probed right before IsoXmitIntMask.
Reported-by: Clifford Dunn
Reported-by: Craig Moore <craig.moore@qenos.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
'0' is now used as the default cmd_per_lun value,
so there's no need to explicitly set it to '1' in the
host template.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there are no more users kill dev_rebuild_header and all of it's
implementations.
This is long overdue.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel was using the vendor ID 0xd00d1e, which was inherited from
the old ieee1394 driver stack. However, this ID was not registered, and
invalid.
Instead, use the vendor/model IDs that are now officially assigned to
the kernel:
https://ieee1394.wiki.kernel.org/index.php/IEEE_OUI_Assignments
[stefanr:
- The vendor ID 001f11 is Openmoko, Inc.'s identifier, registered at
IEEE Registration Authority.
- The range of model IDs 023900...0239ff are the Linux kernel 1394
subsystem's identifiers, registered at Openmoko.
- Model ID 023901 is picked by the subsystem developers as
firewire-core's model ID.]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
[Bart van Asche:] SCSI core never sets cmd->sc_data_direction to
DMA_BIDIRECTIONAL; scsi_bidi_cmnd(cmd) should be used instead to
test for a bidirectional command.
[Christoph Hellwig:] Bidirectional commands won't ever be queued
anyway, unless a LLD or transport driver sets QUEUE_FLAG_BIDI.
So, simply remove the respective queuecommand check in the SBP-2
transport driver.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Remove the function ar_prev_buffer_index() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
firewire-core uses fw_card.lock to protect topology data and transaction
data. firewire-sbp2 uses fw_card.lock for entirely unrelated purposes.
Introduce a sbp2_target.lock to firewire-sbp2 and replace all
fw_card.lock uses in the driver. fw_card.lock is now entirely private
to firewire-core. This has no immediate advantage apart from making it
clear in the code that firewire-sbp2 does not interact with the core
via the core lock.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Users of card->lock Calling context
------------------------------------------------------------------------
sbp2_status_write AR-req handler, tasklet
complete_transaction AR-resp or AT-req handler, tasklet
sbp2_send_orb among else scsi host .queuecommand, which may
be called in some sort of atomic context
sbp2_cancel_orbs sbp2_send_management_orb/
sbp2_{login,reconnect,remove},
worklet or process
sbp2_scsi_abort, scsi eh thread
sbp2_allow_block sbp2_login, worklet
sbp2_conditionally_block among else complete_command_orb, tasklet
sbp2_conditionally_unblock sbp2_{login,reconnect}, worklet
sbp2_unblock sbp2_{login,remove}, worklet or process
Drop the IRQ flags saving from sbp2_cancel_orbs,
sbp2_conditionally_unblock, and sbp2_unblock.
It was already omitted in sbp2_allow_block.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The assertion in the comment in sbp2_allow_block() is no longer true.
Or maybe it never was true. At least now, the sole caller of
sbp2_allow_block(), sbp2_login, can run concurrently to one of
sbp2_unblock()'s callers, sbp2_remove.
sbp2_login is performed by sbp2_logical_unit.work.
sbp2_remove is performed by fw_device.work.
sbp2_remove cancels sbp2_logical_unit.work, but only after it called
sbp2_unblock.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
fw_csr_string() truncates and terminates target strings like strlcpy()
does. Unlike strlcpy(), it returns the target strlen, not the source
strlen, hence users of fw_csr_string() are unable to detect truncation.
Point this behavior out in the kerneldoc comment.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Stefan Richter
Jarod Wilson
Alexey Khoroshilov
Florian Westphal
Linus Torvalds
Andy Lutomirski
Tina Ruchandani
Mel Gorman
Amitoj Kaur Chawla
Hannes Reinecke
David S. Miller
Eric W. Biederman
Clemens Ladisch
Rickard Strandqvist