- Use updated printk format for OF node names
- Fix TI code to only search DT subnodes
- Various static analysis finds
* clk-dt-name:
clk: Convert to using %pOFn instead of device_node.name
* clk-ti-of-node:
clk: ti: fix OF child-node lookup
* clk-sa:
clk: mvebu: armada-37xx-tbg: Switch to clk_get and balance it in probe
reset: hisilicon: fix potential NULL pointer dereference
clk: cdce925: release child device nodes
clk: qcom: clk-branch: Use true and false for boolean values
The OSTM timer driver for RZ/A2 uses TIMER_OF_DECLARE which requires the
ostm module clocks to be registers early in boot.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for SoCs that need to register core and module clocks early in
order to use OF drivers that exclusively use macros such as
TIMER_OF_DECLARE.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the R7S9210 (RZ/A2) Clock Pulse Generator and Module
Standby.
The Module Standby HW in the RZ/A series is very close to R-Car HW, except
for how the registers are laid out.
The MSTP registers are only 8-bits wide, there are no status registers
(MSTPSR), and the register offsets are a little different. Since the RZ/A
hardware manuals refer to these registers as the Standby Control Registers,
we'll use that name to distinguish the RZ/A type from the R-Car type.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Rob Herring <robh@kernel.org> # DT bits
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The TMU clocks weren't present in the original R8A77970 patch by Daisuke
Matsushita, they were added in a later BSP version...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The clock for UARTs 0 through 2 is UART012, the clock for UARTs 3 through
7 is UART34567.
For UART012, we stop the clock driver from changing the clock rate. This
is because the Synopsys UART driver simply sets the reference clock to 16x
the baud rate, but doesn't check if the actual rate is within the required
tolerance. The RZ/N1 clock divider can't provide this (we have to rely on
the UART's internal divider to set the correct clock rate), so you end up
with a clock rate that is way off what you wanted.
In addition, since the clock is shared between multiple UARTs, you don't
want the driver trying to change the clock rate as it may affect the other
UARTs (which may not have been configured yet, so you don't know what baud
rate they will use). Normally, the clock rate is set early on before Linux
to some very high rate that supports all of the clock rates you want.
This change stops the UART34567 clock rate from changing for the same
reasons.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On R-Car V3M (AKA R8A77970), the SD0CKCR is laid out differently than on
the other R-Car gen3 SoCs. In fact, the layout is the same as on R-Car gen2
SoCs, so we'll need to copy the divisor tables from the R-Car gen2 driver.
We'll also need to support the SoC specific clock types, thus we're adding
CLK_TYPE_GEN3_SOC_BASE at the end of 'enum rcar_gen3_clk_types', declare
SD0H/SDH clocks in 'enum r8a77970_clk_types', and handle those clocks in
the overridden cpg_clk_register() method; then, finally, add the SD-IF
module clock (derived from the SD0 clock).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When trying to use I2C7 on R-Car E3:
renesas-cpg-mssr e6150000.clock-controller: Cannot get module clock 1003: -2
i2c-rcar e6690000.i2c: failed to add to PM domain always-on: -2
i2c-rcar: probe of e6690000.i2c failed with error -2
Unlike other R-Car Gen3 SoCs, R-Car E3 has more than 7 I2C bus
interfaces. Add the forgotten module clock for the 8th instance to fix
this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
On R-Car V3H, RCLK can be switched between EXTALR and the On-Chip
Oscillator using mode pin MD19.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Make the existing support for selecting between clean and SSCG clocks
using MD12 more generic, to allow using other mode pins for arbitrary
clock selection.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Stephen Boyd
Kuninori Morimoto
Chris Brandt
Sergei Shtylyov
Geert Uytterhoeven
Fabrizio Castro
Biju Das
Phil Edworthy
Wolfram Sang
Rob Herring
Hoan Nguyen An
Takeshi Kihara