Step in removing CC_OP: change the representation of CC_OP_FLAGS.
The 8 bits are distributed between 6 variables, which should make
it easy to keep up to date.
The code within cc_helper.c is quite ugly but is only temporary.
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For the most part priviledged opcodes are ifdefed out of the
user-only sparc translator, which will then incorrectly produce
illegal opcode traps. But there are some code paths that
properly raise TT_PRIV_INSN, so we must handle it.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230216054516.1267305-11-richard.henderson@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
These traps are present for sparc64 with ilp32, aka sparc32plus.
Enabling them means adjusting the defines over in signal.c,
and fixing an incorrect usage of abi_ulong when we really meant
the full register, target_ulong.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230216054516.1267305-7-richard.henderson@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Use TT_TRAP.
For sparc32, 0x88 is the "Slowaris" system call, currently BAD_TRAP
in the kernel's ttable_32.S. For sparc64, 0x110 is tl0_linux32, the
sparc32 trap, now folded into the TARGET_ABI32 case via TT_TRAP.
For sparc64, there does still exist trap 0x111 as tl0_oldlinux64,
which was replaced by 0x16d as tl0_linux64 in 1998. Since no one
has noticed, don't bother implementing it now.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230216054516.1267305-3-richard.henderson@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The linux kernel's trap tables vector all unassigned trap
numbers to BAD_TRAP, which then raises SIGILL.
Tested-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reported-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This value is fully internal to qemu, and so is not a TARGET define.
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This value is fully internal to qemu, and so is not a TARGET define.
We use this as an extra marker for both host and target errno.
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The fallback code in cpu_loop_exit_sigsegv is sufficient
for sparc linux-user.
This makes all of the code in mmu_helper.c sysemu only, so remove
the ifdefs and move the file to sparc_softmmu_ss. Remove the code
from cpu_loop that handled TT_DFAULT and TT_TFAULT.
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
qemu.h is included in various non-linux-user files (which
mostly want the TaskState struct and the functions for
doing usermode access to guest addresses like lock_user(),
unlock_user(), get_user*(), etc).
Split out the parts that are only used in linux-user itself
into a new user-internals.h. This leaves qemu.h with basically
three things:
* the definition of the TaskState struct
* the user-access functions and macros
* do_brk()
all of which are needed by code outside linux-user that
includes qemu.h.
The addition of all the extra #include lines was done with
sed -i '/include.*qemu\.h/a #include "user-internals.h"' $(git grep -l 'include.*qemu\.h' linux-user)
(and then undoing the change to fpa11.h).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210908154405.15417-8-peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
