If an ESP command is issued in an incorrect mode then an illegal command
interrupt should be generated. Add a new esp_cmd_is_valid() function to
indicate whether the ESP command is valid for the current mode, and if not
then raise the illegal command interrupt.
This fixes WinNT MIPS which issues ICCS after a Chip Reset which is not
permitted, but will fail with an INACCESSIBLE_BOOT_DEVICE error unless an
interrupt is generated.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: 83428f7a97 ("esp.c: move write_response() non-DMA logic to esp_do_nodma()")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2464
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250711204636.542964-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Add a new asc_mode property to ESPState which indicates the current mode of
the ESP and update the ESP state machine accordingly.
Bump the vmstate version and include migration logic to ensure that asc_mode
is set to initiator mode such that any commands in progress will always
continue.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250711204636.542964-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
SCSIDevice keeps track of in-flight requests for device reset and Task
Management Functions (TMFs). The request list requires protection so
that multi-threaded SCSI emulation can be implemented in commits that
follow.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20250311132616.1049687-5-stefanha@redhat.com>
Tested-by: Peter Krempa <pkrempa@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currently the DRQ IRQ is updated every time DMA data is sent/received which
is both inefficient and causes excessive logging of the DRQ state. Add a
new drq_state bool that only updates the DRQ IRQ if its state changes.
This commit adds the new drq_state bool to the migration state: since the
version number has already been increased earlier in the series, there is
no need to repeat it again here. The DRQ IRQ is (currently) only used for
PDMA transfers which already have a migration break in this series so
there are no problems setting its value post-load.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-87-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
According to the datasheet the previous ESP command remains in the ESP_CMD
register, which caused a problem when consecutive TI commands were issued as
it becomes impossible for the state machine to know when the first TI
command finishes.
This was the original reason for introducing the ti_cmd field which kept
track of the last written command for this purpose. However closer reading
of the datasheet shows that a TI command that terminates due to a change of
SCSI target phase resets the ESP_CMD register to zero which solves this
problem.
Now that this has been fixed in the previous commit, remove the unneeded
ti_cmd field and access the ESP_CMD register directly instead. Bump the
vmstate_esp version to indicate that the ti_cmd field is no longer included.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-64-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
usb-storage is for the most part just a wrapper around an internally
created scsi-disk device. It uses DEFINE_BLOCK_PROPERTIES() to offer all
of the usual block device properties to the user, but then only forwards
a few select properties to the internal device while the rest is
silently ignored.
This changes scsi_bus_legacy_add_drive() to accept a whole BlockConf
instead of some individual values inside of it so that usb-storage can
now pass the whole configuration to the internal scsi-disk. This enables
the remaining block device properties, e.g. logical/physical_block_size
or discard_granularity.
Buglink: https://issues.redhat.com/browse/RHEL-22375
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20240131130607.24117-1-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Stop depending on the AioContext lock and instead access
SCSIDevice->requests from only one thread at a time:
- When the VM is running only the BlockBackend's AioContext may access
the requests list.
- When the VM is stopped only the main loop may access the requests
list.
These constraints protect the requests list without the need for locking
in the I/O code path.
Note that multiple IOThreads are not supported yet because the code
assumes all SCSIRequests are executed from a single AioContext. Leave
that as future work.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-ID: <20231204164259.1515217-2-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 1880ad4f4e ("virtio-scsi: Batched prepare for cmd reqs") split
calls to scsi_req_new() and scsi_req_enqueue() in the virtio-scsi device.
No ill effects were observed until commit 8cc5583abe ("virtio-scsi: Send
"REPORTED LUNS CHANGED" sense data upon disk hotplug events") added a
unit attention that was easy to trigger with device hotplug and
hot-unplug.
Because the two calls were separated, all requests in the batch were
prepared calling scsi_req_new() to report a sense. The first one
submitted would report the right sense and reset it to NO_SENSE, while
the others reported CHECK_CONDITION with no sense data. This caused
SCSI errors in Linux.
To solve this issue, let's fetch the unit attention as early as possible
when we prepare the request, so that only the first request in the batch
will use the unit attention SCSIReqOps and the others will not report
CHECK CONDITION.
Fixes: 1880ad4f4e ("virtio-scsi: Batched prepare for cmd reqs")
Fixes: 8cc5583abe ("virtio-scsi: Send "REPORTED LUNS CHANGED" sense data upon disk hotplug events")
Reported-by: Thomas Huth <thuth@redhat.com>
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2176702
Co-developed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-ID: <20230712134352.118655-2-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The virtio-scsi Host Bus Adapter provides access to devices on a SCSI
bus. Those SCSI devices typically have a BlockBackend. When the
BlockBackend enters a drained section, the SCSI device must temporarily
stop submitting new I/O requests.
Implement this behavior by temporarily stopping virtio-scsi virtqueue
processing when one of the SCSI devices enters a drained section. The
new scsi_device_drained_begin() API allows scsi-disk to message the
virtio-scsi HBA.
scsi_device_drained_begin() uses a drain counter so that multiple SCSI
devices can have overlapping drained sections. The HBA only sees one
pair of .drained_begin/end() calls.
After this commit, virtio-scsi no longer depends on hw/virtio's
ioeventfd aio_set_event_notifier(is_external=true). This commit is a
step towards removing the aio_disable_external() API.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20230516190238.8401-19-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Section 5.6.6.3 of VirtIO specification states, "Events will also
be reported via sense codes..." However, no sense data is sent when
VIRTIO_SCSI_EVT_RESET_RESCAN or VIRTIO_SCSI_EVT_RESET_REMOVED events
are reported (when disk hotplug/hotunplug events occur). SCSI layer
on Solaris depends on this sense data, and hence does not handle disk
hotplug/hotunplug events.
When the disk inventory changes, use the bus unit attention mechanism
to return a CHECK_CONDITION status with sense data of 0x06/0x3F/0x0E
(sense code REPORTED_LUNS_CHANGED). The first device on the bus to
execute a command successfully will report and consume the unit
attention status.
Signed-off-by: Venu Busireddy <venu.busireddy@oracle.com>
Message-Id: <20221006194946.24134-1-venu.busireddy@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a SCSI command is received from the guest, the CDB length implied
by the first byte might exceed the number of bytes the guest sent. In
this case scsi_req_new() will read uninitialized data, causing
unpredictable behavior.
Adds the buf_len parameter to scsi_req_new() and plumbs it through the
call stack.
Signed-off-by: John Millikin <john@john-millikin.com>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1127
Message-Id: <20220817053458.698416-1-john@john-millikin.com>
[Fill in correct length for adapters other than ESP. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When A/UX configures the CDROM device it sends a truncated MODE SELECT request
for page 1 (MODE_PAGE_R_W_ERROR) which is only 6 bytes in length rather than
10. This seems to be due to bug in Apple's code which calculates the CDB message
length incorrectly.
The work at [1] suggests that this truncated request is accepted on real
hardware whereas in QEMU it generates an INVALID_PARAM_LEN sense code which
causes A/UX to get stuck in a loop retrying the command in an attempt to succeed.
Alter the mode page request length check so that truncated requests are allowed
if the SCSI_DISK_QUIRK_MODE_PAGE_TRUNCATED quirk is enabled, whilst also adding a
trace event to enable the condition to be detected.
[1] https://68kmla.org/bb/index.php?threads/scsi2sd-project-anyone-interested.29040/page-7#post-316444
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both MacOS and A/UX make use of vendor-specific MODE SELECT commands with PF=0
to identify SCSI devices:
- MacOS sends a MODE SELECT command with PF=0 for the MODE_PAGE_VENDOR_SPECIFIC
(0x0) mode page containing 2 bytes before initialising a disk
- A/UX (installed on disk) sends a MODE SELECT command with PF=0 during SCSI
bus enumeration, and gets stuck in an infinite loop if it fails
Add a new SCSI_DISK_QUIRK_MODE_PAGE_VENDOR_SPECIFIC_APPLE quirk to allow both
PF=0 MODE SELECT commands and implement a MODE_PAGE_VENDOR_SPECIFIC (0x0)
mode page which is compatible with MacOS.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
