The LASI chip is a multi I/O chip used in many older PA-RISC machines.
It includes functionality for NCR710 SCSI, serial, parallel, audio,
i82596 networking and PS/2 ports.
Add the functionality for NCR710_SCSI to the LASI Kconfig option
and move over the relevant parts from the generic HPPA_B160L Kconfig
option to get the dependency right.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Add a new device, ivshmem-flat, which is similar to the ivshmem PCI but
does not require a PCI bus. It's meant to be used on machines like those
with Cortex-M MCUs, which usually lack a PCI/PCIe bus, e.g. lm3s6965evb
and mps2-an385.
The device currently only supports the sysbus bus.
The new device, just like the ivshmem PCI device, supports both peer
notification via hardware interrupts and shared memory.
The device shared memory size can be set using the 'shmem-size' option
and it defaults to 4 MiB, which is the default size of shmem allocated
by the ivshmem server.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1134
Signed-off-by: Gustavo Romero <gustavo.romero@linaro.org>
[PMD: Rebased updating Property and using DEFINE_TYPES macro]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20241216141818.111255-2-gustavo.romero@linaro.org>
The ecc.c code was used only by the PXA2xx and OMAP2 SoC devices,
which we have removed, so it is now completely unused.
Note that hw/misc/eccmemctl.c does not in fact use any of the
code frome ecc.c, so that KConfig dependency was incorrect.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20241003140010.1653808-6-peter.maydell@linaro.org
Generic RCC class for STM32 devices. It can be used for most of
the STM32 chips. Note that it only implements enable and reset
capabilities.
Signed-off-by: Roman Cardenas Rodriguez <rcardenas.rod@gmail.com>
[PMM: tweaked commit message, added MAINTAINERS lines]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For powernv10-rainier, the Power Hypervisor code expects to see a
pca9554 device connected to the 3rd PNV I2C engine on port 1 at I2C
address 0x25 (or left-justified address of 0x4A). This is used by
the hypervisor code to detect if a "Cable Card" is present.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This adds a non-cryptographic grade implementation of the
model for the True Random Number Generator (TRNG) component
in AMD/Xilinx Versal device family.
This implements all 3 modes defined by the actual hardware
specs, all of which selectable by guest software at will
at anytime:
1) PRNG mode, in which the generated sequence is required to
be reproducible after reseeded by the same 384-bit value
as supplied by guest software.
2) Test mode, in which the generated sequence is required to
be reproducible ater reseeded by the same 128-bit test
seed supplied by guest software.
3) TRNG mode, in which non-reproducible sequence is generated
based on periodic reseed by a suitable entropy source.
This model is only intended for non-real world testing of
guest software, where cryptographically strong PRNG or TRNG
is not needed.
This model supports versions 1 & 2 of the device, with
default to be version 2; the 'hw-version' uint32 property
can be set to 0x0100 to override the default.
Other implemented properties:
- 'forced-prng', uint64
When set to non-zero, mode 3's entropy source is implemented
as a deterministic sequence based on the given value and other
deterministic parameters.
This option allows the emulation to test guest software using
mode 3 and to reproduce data-dependent defects.
- 'fips-fault-events', uint32, bit-mask
bit 3: Triggers the SP800-90B entropy health test fault irq
bit 1: Triggers the FIPS 140-2 continuous test fault irq
Signed-off-by: Tong Ho <tong.ho@amd.com>
Message-id: 20231031184611.3029156-2-tong.ho@amd.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds minimal support for AXP-221 PMU and connect it to
bananapi M2U board.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
