Add a minimal sample that showcases minimal ROM sizes. It can be built
in several configurations, all very restrictive when it comes to
features enabled in order to verify the fact that we can fit in small
devices and to be able to accurately measure the sizes of the kernel's
basic features.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This sample did not enable gpio driver, so nothing happens after flash
firmware into a board.
By enabling gpio driver to fix it.
Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
A new role :zephyr_file: is available that renders to a link to the file
or folder in GitHub. Find appropriate references using :file: and
convert to :zephyr_file: to take advantage of its linking capability.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Most of the basic tests trigger LEDs or expect button press and would
hang in device testing because we can't parse success or failure from
the console. Define harness for this with the intent to skip those in
sanitycheck device testing and until we have a better way to test those.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some boards' configuration does not enable GPIO by default,
like nrf52_pca10056, it causes ASSERTION FAIL when running
this application. This fix is to enable GPIO by default for
the basic threads sample, like basic blinky sample does.
Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
commit ddf744deee ("drivers: pwm_nrfx: Use Device Tree label as
instance name") removed the config setting for PWM names and replaced
it with DT_NORDIC_NRF_PWM_PWM_*_LABEL.
This change is causing the blink_led and fade_led samples to break
when compiled for nRF52 boards.
Let's update the samples to use the DT setting.
Signed-off-by: Michael Scott <mike@foundries.io>
Update the filters that are extracting info from DT to use a define that
has a DT_ prefix so its clear that its coming from DT_. Also this lets
us remove any non-DT prefixed defines in the conf db.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Indicate that PWM is supported on several Nordic DK boards so that
the pwm_nrf5_sw and pwm_nrfx drivers are covered by CI builds.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Enable HW PWM driver instead of the SW one on nRF SoCs where the PWM
peripheral is present.
Default PWM instances are also enabled on Nordic DK boards so that it
is possible to build the basic fade_led sample for them without extra
adjustments.
After the above changes are applied, some configuration alterations
in basic samples blink_led and fade_led become no longer needed.
These are removed. And the blink_led sample is corrected so that it
works with the nRF HW PWM driver as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Supported PWM at pins A0, D3, D5 and D6 which are also Arduino
compatible. Also the onboard red LED can be used with PWM.
The basic/{fade_led, blink_led} samples to apply to this board
seemlessly and operate on the onboard red LED.
Also supported RTC.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
blinky/button and disco samples are now using definitions
generated from boards dts files.
Update samples README files accordingly.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
It is safe to assume that if X_GPIO_CONTROLLER is defined (hence
generated) X_GPIO_PIN should also be defined.
If this is not the case, this is an issue and letting the sample
build will reveal the issue.
Update the yaml filter to rely only on _GPIO_CONTROLLER #define's
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In disco basic sample, same GPIO controller was used for LED0
and LED1, which is actually a particular case.
This change implements the general case, where LED0 an LED1 might
not have the same gpio controller.
Tested on nucleo_f429zi and frdm_k64f.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Since the Arduino 101 and the Quark SE C1000 are not actively developed
boards, default to other boards that are maintained and used.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Do not limit to whitelisted boards, instead make it build/run for any
board that defines required DTS macros.
Remove QMSI kconfigs and depend on DTS only.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Do not limit to whitelisted boards, instead make it build/run for any
board that defines required DTS macros.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Do not limit to whitelisted boards, instead make it build/run for any
board that defines required DTS macros.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
1. Modified fade_led PWM example to include
nRF HW PWM option.
2. Added fade_led nrf52_pca10040.overlay
in order to enable PWM node and choose
output PWM GPIO for channel 0. Channel 1
GPIO enable but not used in sample src.
Signed-off-by: Gaute Gamnes <gaute.gamnes@nordicsemi.no>
