Adds driver for pwm on xmc4xxx using Capture Compare Unit 8 (CCU8)
module. There are two CCU8 nodes with each one having four slices.
Each slice has two output channels.
Unlike CCU4, this module can generate complementary high-side/low-side
signals for each output channel. A variable dead time can be added
during the off to on transitions to make sure that the
high-side/low-side signals are not on at the same time.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Adds driver for pwm on xmc4xxx using Capture Compare Unit 4 (CCU4)
module. There are four CCU4 with each one having four channels
Thus it's possible to have up to 16 pwm output signals. The output of
each channel can only be connected to a specific port/pin. The possible
connection and gpio configurations are defined using pinctrl.
The CCU4 module also has a capture mode. Capture support will be added
in the future.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
The malloc arena/heap size setting can be adjusted using different
Kconfig options, depending on the libc implementation. This means
prj.conf can't be used to set this value on projects that can be built
for multiple libcs without generating a Kconfig warning.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This is no longer necessary, as this option is selected as a dependency
for class implementations where it is required.
Also remove redundant test cases.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add the dts and config overlay for nxp_adsp_imx8m board
in order to have the openamp_rsc_table sample working on
HiFi4 DSP from i.MX 8M Plus.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Add initial version of Infineon CAT1 counter driver
Add initial version of binding file for Infineon
Add counters to psco6 dtsi
Add external trigger pin that runs counter
Signed-off-by: Pavlo Havrylyuk <pavlo.havrylyuk@infineon.com>
The intent of this change is to add custom shell configurations for
intel_socfpga_agilex* based boards. As of now, configurations are
added for 'intel_socfpga_agilex5_socdk' board.
Signed-off-by: Girisha Dengi <girisha.dengi@intel.com>
Refactor the ESP32 target SOCs together with
all related boards. Most braking changes includes:
- changing the CONFIG_SOC_ESP32* to refer to
the actual soc line (esp32,esp32s2,esp32s3,esp32c3)
- replacing CONFIG_SOC with the CONFIG_SOC_SERIES
- creating CONFIG_SOC_FAMILY_ESP32 to embrace all
the ESP32 across all used architectures
- introducing CONFIG_SOC_PART_NUMBER_* to
provide a SOC model config
- introducing the 'common' folder to hide all
commonly used configs and files.
- updating west.yml to reflect previous changes in hal
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Remove virtual esp32 board and replace it with the
real word boards:
- esp32_devkitc_wroom
- esp32_devkitc_wrover (with PSRAM option)
Signed-off-by: Marek Matej <marek.matej@espressif.com>
There is some ambiguity with the DHCPv4 handling in the dns_resolve
sample. On one hand, the sample uses net_config library, which does
initiate the DHCPv4 on the interface (if enabled) and may block the
initialization until the address is assigned (in case there is no other
statically assigned IPv4 addresses.) On the other hand, the sample
registers for NET_EVENT_IPV4_ADDR_ADD in case DHCPv4 is in use, delaying
the DNS queries until address is assigned.
In case net_config delayed the initialization however, this will not
work, as the event handler will be registered only after DHCPv4 address
is assigned, so the callback will not get executed.
Fix this, by checking if DHCPv4 assigned address already exists on an
interface - if so, schedule DNS queries immediately. Otherwise (for
example in case when net_config was not configured to wait for address)
register an event callback, and schedule queries from there.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Enable PXP rotation for LVGL sample. The PXP is configured to
rotate by 0 degrees, so the original image is left untouched.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enable PXP engine with RT1170 EVK. The PXP is set to rotate by 0
degrees in the LVGL sample, for testing purposes.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
- Add overlay for the esp32s2_saola board to die_temp_polling sample.
- Add aliases for the die_temp_polling sample to esp32s2 dtsi.
Signed-off-by: Hiroki Tada <tada.hiroki@fujitsu.com>
Add sample to demonstrate usage of IS31FL3733 LED using the LED API.
This led matrix controller has several custom APIs to expose
functionality not available within the standard led API, such as
limiting LED current.
Signed-off-by: Daniel DeGrasse <daniel@degrasse.com>
