Adds driver for pwm on xmc4xxx using Capture Compare Unit 8 (CCU8)
module. There are two CCU8 nodes with each one having four slices.
Each slice has two output channels.
Unlike CCU4, this module can generate complementary high-side/low-side
signals for each output channel. A variable dead time can be added
during the off to on transitions to make sure that the
high-side/low-side signals are not on at the same time.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Adds driver for pwm on xmc4xxx using Capture Compare Unit 4 (CCU4)
module. There are four CCU4 with each one having four channels
Thus it's possible to have up to 16 pwm output signals. The output of
each channel can only be connected to a specific port/pin. The possible
connection and gpio configurations are defined using pinctrl.
The CCU4 module also has a capture mode. Capture support will be added
in the future.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
CC13/26xx's pinctrl_cc13xx_cc26xx.c driver included ioc.h and
(indirectly) pinctrl_soc.h which contained duplicate defines.
This change removes the header conflict and redundant definitions.
This prepares for subsequent changes in this change set that add
additional flags to the pinctrl driver which would otherwise trigger the
header conflict.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Added a driver for the DFRobot A01NYUB distance sensor. This sensor
sends its readings via UART at 9600 baud. This driver uses interrupts
to read the data from the sensor.
Signed-off-by: Oliver King <oliver.king@steadconnect.com>
Startup power domains according to the expected final state given the
power supply and PM device runtime support.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Let the driver compile without `PM_DEVICE_POWER_DOMAIN`, in which case
the driver only controls the GPIO, without notifying dependant devices.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Implement `gpio_pin_get_config` for the stellaris platform, and by
extension `qemu_cortex_m3`.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
This is a follow-up to commit 4c20403629.
CONTAINER_OF() cannot be used to obtain the device pointer from its
data pointer as this data is not contained in the device structure.
Instead, use a dedicated member in the device data structure to store
the device pointer.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for flash NOR memory devices on a NXP S32 QSPI bus. The
driver uses a fixed LUT configuration assuming a default standard page
size and erase types, and allows to select between multiple read/program
instructions/modes. It is also possible to read the flash device
characteristics from the device at run-time as long as the memory is
JESD216 compatible, providing more flexibility.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The NXP S32 QSPI controller acts as an interface to up to two serial
flash memory devices, each with up to eight bidirectional data lines,
depending on the platform. It is based on a LUT enginee to interface
through commands with different memory types including flash NOR and
Hyperram.
This patch adds support for the QSPI in S32K344 which supports a single
memory device (side A) with up to four bidirectional data lines and SDR
only. Nevertheless, the memory controller is implemented flexible enough
to be extended to support more feature-rich QSPI blocks.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
This commit aligns TWIM shim to utilize memory-region property.
The memory-region is not required property that enables user
to specify placement of dma buffers in memory region.
It is done by assigning to memory-region property,
phandle to node with zephyr,memory-region and mimo-sram compatible.
When memory-region property is not specified for given
instance, buffer is placed in default RAM region with other data.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
There are two different i2c node properites `zephyr,flash-buf-max-size`
and `zephyr,concat-buf-size`. In the end max value of that two is used
to define size of the message buffer.
It's redundant to store both values in device config structure.
Changed config structure to contain only bigger value.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Add initial version of Infineon CAT1 counter driver
Add initial version of binding file for Infineon
Add counters to psco6 dtsi
Add external trigger pin that runs counter
Signed-off-by: Pavlo Havrylyuk <pavlo.havrylyuk@infineon.com>
Each PSCI interface versions have different DT compatible strings
like arm,psci-0.2, arm,psci-1.1 and so on. However, the same driver
can be used for all the versions by adding #define DT_COMPAT for
required version and #undef DT_COMPAT for default version.
Add support for PSCI cold reset, warm reset and cpu-on function IDs.
Signed-off-by: Girisha Dengi <girisha.dengi@intel.com>
Signed-off-by: Navinkumar Balabakthan <navinkumar.balabakthan@intel.com>
If the optional hardware reset line is available, this change
will use that reset line to assert the uart module and bring
it out of reset state to use.
Signed-off-by: Girisha Dengi <girisha.dengi@intel.com>
This is Intel's proprietary IP which controls individual module
reset signals. During each system driver initialization, these
reset signals will be used to bring module out of reset state.
Signed-off-by: Navinkumar Balabakthan <navinkumar.balabakthan@intel.com>
Signed-off-by: Girisha Dengi <girisha.dengi@intel.com>
This is Intel's proprietary IP which supply the clock for all the
system peripherals. Clock manager is initialized only one time
during boot up by FSBL (ATF BL2) based on external user settings.
Signed-off-by: Girisha Dengi <girisha.dengi@intel.com>
Refactor the ESP32 target SOCs together with
all related boards. Most braking changes includes:
- changing the CONFIG_SOC_ESP32* to refer to
the actual soc line (esp32,esp32s2,esp32s3,esp32c3)
- replacing CONFIG_SOC with the CONFIG_SOC_SERIES
- creating CONFIG_SOC_FAMILY_ESP32 to embrace all
the ESP32 across all used architectures
- introducing CONFIG_SOC_PART_NUMBER_* to
provide a SOC model config
- introducing the 'common' folder to hide all
commonly used configs and files.
- updating west.yml to reflect previous changes in hal
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Ethernet MAC addresses are not unique enough
use unique_device_ID full range (96 bits)
call crc32_ieee() to generate last 3 bytes of mac address
Signed-off-by: Marc Desvaux <marc.desvaux-ext@st.com>
