This also adds the ability to incorporate arrays into netlink messages
and to determine when a netlink message is too big, used by some generic
netlink protocols.
commit 7715629 (networkd: Fix race condition in [RoutingPolicyRule] handling (#7615)).
Does not fix race. Still there is a race in case of bride because the
bride goes down and up .
calling route_configure then link_set_routing_policy_rule and the
link_check_ready makes a race between routing_policy_rule_messages and route_messages.
While bride comes up and we call the call again route_configure if finds
it self in the callback function LINK_STATE_CONFIGURED networkd dies.
Let's handle first routing policy rules then route_configure. This fixes
the crash.
Closes#7797
When /sys is a symlink to the sysfs mountpoint, e.g. /path/to/sysfs.
Then, device->syspath was set to like /path/to/sysfs/devices/foo/baz.
This converts the path to /sys/devices/foo/baz.
Fixes#7676.
Currently, if there are two /proc/self/mountinfo entries with the same
mount point path, the mount setup flags computed for the second of
these two entries will overwrite the mount setup flags computed for
the first of these two entries. This is the root cause of issue #7798.
This patch changes mount_setup_existing_unit to prevent the
just_mounted mount setup flag from being overwritten if it is set to
true. This will allow all mount units created from /proc/self/mountinfo
entries to be initialized properly.
Fixes: #7798
When loading .netdev files we parse them twice: first we do one parsing
iteration to figure out their "kind", and then we do it again to parse
out the kind's parameters. The first iteration is run with a "short"
NetDev structure, that only covers the generic NetDev properties. Which
should be enough, as we don't parse the per-kind properties. However,
before this patch we'd still try to destruct the per-kind properties
which resulted in memory corruption. With this change we distuingish the
two iterations by the state field, so that the destruction only happens
when the state signals we are running with a full NetDev structure.
Since this is not obvious, let's add a lot of comments.
This is unused since kdbus is gone, hence remove this too. This permits
us to get rid of sd_bus_send_internal() and just implement sd_bus_send()
directly.
This way, clients can install the very same match on direct and broker
connections as in both cases the messages will originate from the o.f.s1
service.
This is useful on direct connections to generate messages with valid
sender fields.
This is particularly useful for services that are accessible both
through direct connections and the broker, as it allows clients to
install matches on the sender service name, and they work the same in
both cases.
This way sd_bus_call_method_async() (which is just a wrapper around
sd_bus_call_async()) can be used to put method calls together that
expect no reply.
The changes both networkd and resolved to make use of the watch_bind
feature of sd-bus to connect to the system bus. This way, both daemons
can be started during early boot, and automatically and instantly
connect to the system bus as it becomes available.
This replaces prior code that used a time-based retry logic to connect
to the bus.
With this new API sd-bus can synthesize a local "Connected" signal when
the connection is fully established. It mirrors the local "Disconnected"
signal that is already generated when the connection is terminated. This
is useful to be notified when connection setup is done, in order to
start method calls then, in particular when using "slow" connection
methods (for example slow TCP, or most importantly the "watch_bind"
inotify logic).
Note that one could also use hook into the initial NameAcquired signal
received from the bus broker, but that scheme works only if we actually
connect to a bus. The benefit of "Connected" OTOH is that it works with
any kind of connection.
Ideally, we'd just generate this message unconditionally, but in order
not to break clients that do not expect this message it is opt-in.
This new call is much light sd_bus_is_open(), but returns true only if
the connection is fully set up, i.e. after we finished with the
authentication and Hello() phase. This API is useful for clients in
particular when using the "watch_bind" feature, as that way it can be
determined in advance whether it makes sense to sync on some operation.
Let's directly reference /run instead, so that we can work without /var
being around, or with /var/run being incorrectly set up.
Note that we keep the old socket path in place when referencing the
system bus of containers, as they might be foreign operating systems,
that still don't have adopted /run, and where it makes sense to use the
standardized name instead. On local systems, we insist on /run being set
up properly however, hence this limitation does not apply.
Also, get rid of the UNIX_SYSTEM_BUS_ADDRESS and
UNIX_USER_BUS_ADDRESS_FMT defines. They had a purpose when we still did
kdbus, as we then had to support two different backends. But since
that's gone, we don't need this indirection anymore, hence settle on a
one define only.
