There is an unusual case that the range map covers right up to the top
of system RAM, but leaves a hole somewhere lower down. Then it prevents
the nvme device dma mapping in the checking path of phys_to_dma() and
causes the hangs at boot.
E.g. On an Armv8 Ampere server, the dsdt ACPI table is:
Method (_DMA, 0, Serialized) // _DMA: Direct Memory Access
{
Name (RBUF, ResourceTemplate ()
{
QWordMemory (ResourceConsumer, PosDecode, MinFixed,
MaxFixed, Cacheable, ReadWrite,
0x0000000000000000, // Granularity
0x0000000000000000, // Range Minimum
0x00000000FFFFFFFF, // Range Maximum
0x0000000000000000, // Translation Offset
0x0000000100000000, // Length
,, , AddressRangeMemory, TypeStatic)
QWordMemory (ResourceConsumer, PosDecode, MinFixed,
MaxFixed, Cacheable, ReadWrite,
0x0000000000000000, // Granularity
0x0000006010200000, // Range Minimum
0x000000602FFFFFFF, // Range Maximum
0x0000000000000000, // Translation Offset
0x000000001FE00000, // Length
,, , AddressRangeMemory, TypeStatic)
QWordMemory (ResourceConsumer, PosDecode, MinFixed,
MaxFixed, Cacheable, ReadWrite,
0x0000000000000000, // Granularity
0x00000060F0000000, // Range Minimum
0x00000060FFFFFFFF, // Range Maximum
0x0000000000000000, // Translation Offset
0x0000000010000000, // Length
,, , AddressRangeMemory, TypeStatic)
QWordMemory (ResourceConsumer, PosDecode, MinFixed,
MaxFixed, Cacheable, ReadWrite,
0x0000000000000000, // Granularity
0x0000007000000000, // Range Minimum
0x000003FFFFFFFFFF, // Range Maximum
0x0000000000000000, // Translation Offset
0x0000039000000000, // Length
,, , AddressRangeMemory, TypeStatic)
})
But the System RAM ranges are:
cat /proc/iomem |grep -i ram
90000000-91ffffff : System RAM
92900000-fffbffff : System RAM
880000000-fffffffff : System RAM
8800000000-bff5990fff : System RAM
bff59d0000-bff5a4ffff : System RAM
bff8000000-bfffffffff : System RAM
So some RAM ranges are out of dma_range_map.
Fix it by checking whether each of the system RAM resources can be
properly encompassed within the dma_range_map.
Signed-off-by: Jia He <justin.he@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch moves dma_addressing_limited() out of line, serving as a
preliminary step to prevent the introduction of a new publicly accessible
low-level helper when validating whether all system RAM is mapped within
the DMA mapping range.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jia He <justin.he@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fix these two error paths:
1. When set_memory_decrypted() fails, pages may be left fully or partially
decrypted.
2. Decrypted pages may be freed if swiotlb_alloc_tlb() determines that the
physical address is too high.
To fix the first issue, call set_memory_encrypted() on the allocated region
after a failed decryption attempt. If that also fails, leak the pages.
To fix the second issue, check that the TLB physical address is below the
requested limit before decrypting.
Let the caller differentiate between unsuitable physical address (=> retry
from a lower zone) and allocation failures (=> no point in retrying).
Cc: stable@vger.kernel.org
Fixes: 79636caad3 ("swiotlb: if swiotlb is full, fall back to a transient memory pool")
Signed-off-by: Petr Tesarik <petr.tesarik1@huawei-partners.com>
Reviewed-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Pull dma-mapping updates from Christoph Hellwig:
- get rid of the fake support for coherent DMA allocation on coldfire
with caches (Christoph Hellwig)
- add a few Kconfig dependencies so that Kconfig catches the use of
invalid configurations (Christoph Hellwig)
- fix a type in dma-debug output (Chuck Lever)
- rewrite a comment in swiotlb (Sean Christopherson)
* tag 'dma-mapping-6.7-2023-10-30' of git://git.infradead.org/users/hch/dma-mapping:
dma-debug: Fix a typo in a debugging eye-catcher
swiotlb: rewrite comment explaining why the source is preserved on DMA_FROM_DEVICE
m68k: remove unused includes from dma.c
m68k: don't provide arch_dma_alloc for nommu/coldfire
net: fec: use dma_alloc_noncoherent for data cache enabled coldfire
m68k: use the coherent DMA code for coldfire without data cache
dma-direct: warn when coherent allocations aren't supported
dma-direct: simplify the use atomic pool logic in dma_direct_alloc
dma-direct: add a CONFIG_ARCH_HAS_DMA_ALLOC symbol
dma-direct: add dependencies to CONFIG_DMA_GLOBAL_POOL
When allocating a new pool at runtime, reduce the number of slabs so
that the allocation order is at most MAX_ORDER. This avoids a kernel
warning in __alloc_pages().
The warning is relatively benign, because the pool size is subsequently
reduced when allocation fails, but it is silly to start with a request
that is known to fail, especially since this is the default behavior if
the kernel is built with CONFIG_SWIOTLB_DYNAMIC=y and booted without any
swiotlb= parameter.
Reported-by: Ben Greear <greearb@candelatech.com>
Closes: https://lore.kernel.org/netdev/4f173dd2-324a-0240-ff8d-abf5c191be18@candelatech.com/
Fixes: 1aaa736815 ("swiotlb: allocate a new memory pool when existing pools are full")
Signed-off-by: Petr Tesarik <petr.tesarik1@huawei-partners.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Rewrite the comment explaining why swiotlb copies the original buffer to
the TLB buffer before initiating DMA *from* the device, i.e. before the
device DMAs into the TLB buffer. The existing comment's argument that
preserving the original data can prevent a kernel memory leak is bogus.
If the driver that triggered the mapping _knows_ that the device will
overwrite the entire mapping, or the driver will consume only the written
parts, then copying from the original memory is completely pointless.
If neither of the above holds true, then copying from the original adds
value only if preserving the data is necessary for functional
correctness, or the driver explicitly initialized the original memory.
If the driver didn't initialize the memory, then copying the original
buffer to the TLB buffer simply changes what kernel data is leaked to
user space.
Writing the entire TLB buffer _does_ prevent leaking stale TLB buffer
data from a previous bounce, but that can be achieved by simply zeroing
the TLB buffer when grabbing a slot.
The real reason swiotlb ended up initializing the TLB buffer with the
original buffer is that it's necessary to make swiotlb operate as
transparently as possible, i.e. to behave as closely as possible to
hardware, and to avoid corrupting the original buffer, e.g. if the driver
knows the device will do partial writes and is relying on the unwritten
data to be preserved.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/all/ZN5elYQ5szQndN8n@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Log a warning once when dma_alloc_coherent fails because the platform
does not support coherent allocations at all.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Greg Ungerer <gerg@linux-m68k.org>
The logic in dma_direct_alloc when to use the atomic pool vs remapping
grew a bit unreadable. Consolidate it into a single check, and clean
up the set_uncached vs remap logic a bit as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Greg Ungerer <gerg@linux-m68k.org>
Instead of using arch_dma_alloc if none of the generic coherent
allocators are used, require the architectures to explicitly opt into
providing it. This will used to deal with the case of m68knommu and
coldfire where we can't do any coherent allocations whatsoever, and
also makes it clear that arch_dma_alloc is a last resort.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Greg Ungerer <gerg@linux-m68k.org>
CONFIG_DMA_GLOBAL_POOL can't be combined with other DMA coherent
allocators. Add dependencies to Kconfig to document this, and make
kconfig complain about unmet dependencies if someone tries.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Greg Ungerer <gerg@linux-m68k.org>
When CONFIG_SWIOTLB_DYNAMIC=y, devices which do not use the software IO TLB
can avoid swiotlb lookup. A flag is added by commit 1395706a14 ("swiotlb:
search the software IO TLB only if the device makes use of it"), the flag
is correctly set, but it is then never checked. Add the actual check here.
Note that this code is an alternative to the default pool check, not an
additional check, because:
1. swiotlb_find_pool() also searches the default pool;
2. if dma_uses_io_tlb is false, the default swiotlb pool is not used.
Tested in a KVM guest against a QEMU RAM-backed SATA disk over virtio and
*not* using software IO TLB, this patch increases IOPS by approx 2% for
4-way parallel I/O.
The write memory barrier in swiotlb_dyn_alloc() is not needed, because a
newly allocated pool must always be observed by swiotlb_find_slots() before
an address from that pool is passed to is_swiotlb_buffer().
Correctness was verified using the following litmus test:
C swiotlb-new-pool
(*
* Result: Never
*
* Check that a newly allocated pool is always visible when the
* corresponding swiotlb buffer is visible.
*)
{
mem_pools = default;
}
P0(int **mem_pools, int *pool)
{
/* add_mem_pool() */
WRITE_ONCE(*pool, 999);
rcu_assign_pointer(*mem_pools, pool);
}
P1(int **mem_pools, int *flag, int *buf)
{
/* swiotlb_find_slots() */
int *r0;
int r1;
rcu_read_lock();
r0 = READ_ONCE(*mem_pools);
r1 = READ_ONCE(*r0);
rcu_read_unlock();
if (r1) {
WRITE_ONCE(*flag, 1);
smp_mb();
}
/* device driver (presumed) */
WRITE_ONCE(*buf, r1);
}
P2(int **mem_pools, int *flag, int *buf)
{
/* device driver (presumed) */
int r0 = READ_ONCE(*buf);
/* is_swiotlb_buffer() */
int r1;
int *r2;
int r3;
smp_rmb();
r1 = READ_ONCE(*flag);
if (r1) {
/* swiotlb_find_pool() */
rcu_read_lock();
r2 = READ_ONCE(*mem_pools);
r3 = READ_ONCE(*r2);
rcu_read_unlock();
}
}
exists (2:r0<>0 /\ 2:r3=0) (* Not found. *)
Fixes: 1395706a14 ("swiotlb: search the software IO TLB only if the device makes use of it")
Reported-by: Jonathan Corbet <corbet@lwn.net>
Closes: https://lore.kernel.org/linux-iommu/87a5uz3ob8.fsf@meer.lwn.net/
Signed-off-by: Petr Tesarik <petr@tesarici.cz>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Commit 8ac0406335 ("swiotlb: reduce the number of areas to match
actual memory pool size") calculated the reduced number of areas in
swiotlb_init_remap() but didn't actually use the value. Replace usage of
default_nareas accordingly.
Fixes: 8ac0406335 ("swiotlb: reduce the number of areas to match actual memory pool size")
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This reverts commit 3fa6456ebe.
The Commit broke the CMA region creation through DT on arm64,
as showed below logs with "memblock=debug":
[ 0.000000] memblock_phys_alloc_range: 41943040 bytes align=0x200000
from=0x0000000000000000 max_addr=0x00000000ffffffff
early_init_dt_alloc_reserved_memory_arch+0x34/0xa0
[ 0.000000] memblock_reserve: [0x00000000fd600000-0x00000000ffdfffff]
memblock_alloc_range_nid+0xc0/0x19c
[ 0.000000] Reserved memory: overlap with other memblock reserved region
>From call flow, region we defined in DT was always reserved before entering
into rmem_cma_setup. Also, rmem_cma_setup has one routine cma_init_reserved_mem
to ensure the region was reserved. Checking the region not reserved here seems
not correct.
early_init_fdt_scan_reserved_mem:
fdt_scan_reserved_mem
__reserved_mem_reserve_reg
early_init_dt_reserve_memory
memblock_reserve(using “reg” prop case)
fdt_init_reserved_mem
__reserved_mem_alloc_size
*early_init_dt_alloc_reserved_memory_arch*
memblock_reserve(dynamic alloc case)
__reserved_mem_init_node
rmem_cma_setup(region overlap check here should always fail)
Example DT can be used to reproduce issue:
dump_mem: mem_dump_region {
compatible = "shared-dma-pool";
alloc-ranges = <0x0 0x00000000 0x0 0xffffffff>;
reusable;
size = <0 0x2800000>;
};
Signed-off-by: Zhenhua Huang <quic_zhenhuah@quicinc.com>
Move the #endif a line so that free_page label is only seen by the
compile pass when actually used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chunhui He <hchunhui@mail.ustc.edu.cn>
Reviewed-by: Robin Murphy <roin.murphy@arm.com>
It makes no sense to expose CONFIG_DMA_NUMA_CMA if CONFIG_NUMA is not
enabled, and random config options shouldn't be default unless there
is a good reason. Replace the default NUMA with a depends on to fix both
issues.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <roin.murphy@arm.com>
Use a simple logical shift and increment to calculate the number of slots
taken by the DMA segment boundary.
At least GCC-13 is not able to optimize the expression, producing this
horrible assembly code on x86:
cmpq $-1, %rcx
je .L364
addq $2048, %rcx
shrq $11, %rcx
movq %rcx, %r13
.L331:
// rest of the function here...
// after function epilogue and return:
.L364:
movabsq $9007199254740992, %r13
jmp .L331
After the optimization, the code looks more reasonable:
shrq $11, %r11
leaq 1(%r11), %rbx
Signed-off-by: Petr Tesarik <petr.tesarik.ext@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Move the comment down in front of the loop that actually sets the list
member of struct io_tlb_slot to zero.
Fixes: 26a7e09478 ("swiotlb: refactor swiotlb_tbl_map_single")
Signed-off-by: Petr Tesarik <petr.tesarik.ext@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Skip searching the software IO TLB if a device has never used it, making
sure these devices are not affected by the introduction of multiple IO TLB
memory pools.
Additional memory barrier is required to ensure that the new value of the
flag is visible to other CPUs after mapping a new bounce buffer. For
efficiency, the flag check should be inlined, and then the memory barrier
must be moved to is_swiotlb_buffer(). However, it can replace the existing
barrier in swiotlb_find_pool(), because all callers use is_swiotlb_buffer()
first to verify that the buffer address belongs to the software IO TLB.
Signed-off-by: Petr Tesarik <petr.tesarik.ext@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When swiotlb_find_slots() cannot find suitable slots, schedule the
allocation of a new memory pool. It is not possible to allocate the pool
immediately, because this code may run in interrupt context, which is not
suitable for large memory allocations. This means that the memory pool will
be available too late for the currently requested mapping, but the stress
on the software IO TLB allocator is likely to continue, and subsequent
allocations will benefit from the additional pool eventually.
Keep all memory pools for an allocator in an RCU list to avoid locking on
the read side. For modifications, add a new spinlock to struct io_tlb_mem.
The spinlock also protects updates to the total number of slabs (nslabs in
struct io_tlb_mem), but not reads of the value. Readers may therefore
encounter a stale value, but this is not an issue:
- swiotlb_tbl_map_single() and is_swiotlb_active() only check for non-zero
value. This is ensured by the existence of the default memory pool,
allocated at boot.
- The exact value is used only for non-critical purposes (debugfs, kernel
messages).
Signed-off-by: Petr Tesarik <petr.tesarik.ext@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The value returned by default_swiotlb_limit() should be constant, because
it is used to decide whether DMA can be used. To allow allocating memory
pools on the fly, use the maximum possible physical address rather than the
highest address used by the default pool.
For swiotlb_init_remap(), this is either an arch-specific limit used by
memblock_alloc_low(), or the highest directly mapped physical address if
the initialization flags include SWIOTLB_ANY. For swiotlb_init_late(), the
highest address is determined by the GFP flags.
Signed-off-by: Petr Tesarik <petr.tesarik.ext@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Try to allocate a transient memory pool if no suitable slots can be found
and the respective SWIOTLB is allowed to grow. The transient pool is just
enough big for this one bounce buffer. It is inserted into a per-device
list of transient memory pools, and it is freed again when the bounce
buffer is unmapped.
Transient memory pools are kept in an RCU list. A memory barrier is
required after adding a new entry, because any address within a transient
buffer must be immediately recognized as belonging to the SWIOTLB, even if
it is passed to another CPU.
Deletion does not require any synchronization beyond RCU ordering
guarantees. After a buffer is unmapped, its physical addresses may no
longer be passed to the DMA API, so the memory range of the corresponding
stale entry in the RCU list never matches. If the memory range gets
allocated again, then it happens only after a RCU quiescent state.
Since bounce buffers can now be allocated from different pools, add a
parameter to swiotlb_alloc_pool() to let the caller know which memory pool
is used. Add swiotlb_find_pool() to find the memory pool corresponding to
an address. This function is now also used by is_swiotlb_buffer(), because
a simple boundary check is no longer sufficient.
The logic in swiotlb_alloc_tlb() is taken from __dma_direct_alloc_pages(),
simplified and enhanced to use coherent memory pools if needed.
Note that this is not the most efficient way to provide a bounce buffer,
but when a DMA buffer can't be mapped, something may (and will) actually
break. At that point it is better to make an allocation, even if it may be
an expensive operation.
Signed-off-by: Petr Tesarik <petr.tesarik.ext@huawei.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add a config option (CONFIG_SWIOTLB_DYNAMIC) to enable or disable dynamic
allocation of additional bounce buffers.
If this option is set, mark the default SWIOTLB as able to grow and
restricted DMA pools as unable.
However, if the address of the default memory pool is explicitly queried,
make the default SWIOTLB also unable to grow. This is currently used to set
up PCI BAR movable regions on some Octeon MIPS boards which may not be able
to use a SWIOTLB pool elsewhere in physical memory. See octeon_pci_setup()
for more details.
If a remap function is specified, it must be also called on any dynamically
allocated pools, but there are some issues:
- The remap function may block, so it should not be called from an atomic
context.
- There is no corresponding unremap() function if the memory pool is
freed.
- The only in-tree implementation (xen_swiotlb_fixup) requires that the
number of slots in the memory pool is a multiple of SWIOTLB_SEGSIZE.
Keep it simple for now and disable growing the SWIOTLB if a remap function
was specified.
Signed-off-by: Petr Tesarik <petr.tesarik.ext@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
