Freescale Layerscape Lynx 28G SerDes PHYs are only present on
Freescale/NXP Layerscape SoCs.
Move PHY_FSL_LYNX_28G outside the block for ARCH_MXC, as the latter
is meant for i.MX8 SoCs, which is a different family than Layerscape.
Add a dependency on ARCH_LAYERSCAPE, to prevent asking the user about
this driver when configuring a kernel without Layerscape SoC support.
Fixes: 02e2af20f4 ("Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc")
Fixes: 8f73b37cf3 ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
This patch adds a new generic PHY driver to support the Lynx 28G SerDes
block found on some of the Layerscape SoCs such as LX2160A.
At the moment, only the following Ethernet protocols are supported:
SGMII/1000Base-X and 10GBaseR.
SerDes lanes which are not running an Ethernet protocol or a currently
supported Ethenet protocol will be left as it was configured through the
RCW (Reset Configuration Word) at boot time.
At probe time, the platform driver will read the current
configuration of both PLLs found on a SerDes block and will determine
what protocols are supported using that PLL.
For example, if a PLL is configured to generate a clock net (frate) of
5GHz the only protocols sustained by that PLL are SGMII/1000Base-X
(using a quarter of the full clock rate) and QSGMII using the full clock
net frequency on the lane.
On the .set_mode() callback, the PHY driver will first check if the
requested operating mode (protocol) is even supported by the current PLL
configuration and will error out if not.
Then, the lane is reconfigured to run on the requested protocol.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Cadence D-PHY can be configured in Tx (DSI) mode or Rx (CSI) mode.
Both modes have a different programming sequence and share little among
them. In addition, a PHY configured in Tx mode cannot be used in Rx mode
and vice versa. For this reason, create a separate driver for the Rx
mode to make it easier to read and maintain.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20220301111621.2992275-2-p.yadav@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove old RPC implementation and add a new native kernel implementation.
The old implementation uses ARM SMC API to issue RPC calls to ARM Trusted
Firmware which provides real implementation of PHY configuration.
But older versions of ARM Trusted Firmware do not provide this PHY
configuration functionality, simply returning: operation not supported; or
worse, some versions provide the configuration functionality incorrectly.
For example the firmware shipped in ESPRESSObin board has this older
version of ARM Trusted Firmware and therefore SATA, USB 3.0 and PCIe
functionality do not work with newer versions of Linux kernel.
Due to the above reasons, the following commits were introduced into Linux,
to workaround these issues by ignoring -EOPNOTSUPP error code from
phy-mvebu-a3700-comphy driver function phy_power_on():
commit 45aefe3d22 ("ata: ahci: mvebu: Make SATA PHY optional for Armada
3720")
commit 3241929b67 ("usb: host: xhci: mvebu: make USB 3.0 PHY optional for
Armada 3720")
commit b0c6ae0f89 ("PCI: aardvark: Fix initialization with old Marvell's
Arm Trusted Firmware")
Replace this RPC implementation with proper native kernel implementation,
which is independent on the firmware. Never return -EOPNOTSUPP for proper
arguments.
This should solve multiple issues with real-world boards, where it is not
possible or really inconvenient to change the firmware. Let's eliminate
these issues.
This implementation is ported directly from Armada 3720 comphy driver found
in newest version of ARM Trusted Firmware source code, but with various
fixes of register names, some added comments, some refactoring due to the
original code not conforming to kernel standards. Also PCIe mode poweroff
support was added here, and PHY reset support. These changes are also going
to be sent to ARM Trusted Firmware.
[ Pali did the porting from ATF.
I (Marek) then fixed some register names, some various other things,
added some comments and refactored the code to kernel standards. Also
fixed PHY poweroff and added PHY reset. ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220203214444.1508-3-kabel@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Port number is encoded into argument for SMC call. It is zero for SATA,
PCIe and also both USB 3.0 PHYs. It is non-zero only for Ethernet PHY
(incorrectly called SGMII) on lane 0. Ethernet PHY on lane 1 also uses zero
port number.
So construct "port" bits for SMC call argument can be constructed directly
from PHY type and lane number.
Change driver code to always pass zero port number for non-ethernet PHYs
and for ethernet PHYs determinate port number from lane number. This
simplifies the driver.
As port number from DT PHY configuration is not used anymore, remove whole
driver code which parses it. This also simplifies the driver.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220203214444.1508-2-kabel@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Just like every other family BCM4908 should get its own enum value. That
is required to properly handle it in chipset conditional code.
The real change is excluding BCM4908 from the PLL reprogramming code
(see brcmusb_usb3_pll_54mhz()). I'm not sure what's the BCM4908
reference clock frequency but:
1. BCM4908 custom driver from Broadcom's SDK doesn't reprogram PLL
2. Doing that in Linux driver stopped PHY handling some USB 3.0 devices
This change makes USB 3.0 PHY recognize e.g.:
1. 04e8:6860 - Samsung Electronics Co., Ltd Galaxy series, misc. (MTP mode)
2. 1058:259f - Western Digital My Passport 259F
Broadcom's STB SoCs come with a set of SUN_TOP_CTRL_* registers that
allow reading chip family and product ids. Such a block & register is
missing on BCM4908 so this commit introduces "compatible" string
specific binding.
Fixes: 4b402fa8e0 ("phy: phy-brcm-usb: support PHY on the BCM4908")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220218172459.10431-1-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some Android x86 tablets with a Bay Trail (BYT) SoC and a Crystal Cove
PMIC, which does not support charger-detection, rely on a TUSB1211
phy for charger-detection.
Add support for charger detection on TUSB1211 phy-s and export
the information about the detected charger through the standard
power_supply class interface. power_supply class charger IC drivers
like the bq24190_charger.c driver will then pick this up and set
their input_current_limit based on this.
Note the "linux,phy_charger_detect" property used to enable this is
a special kernel-internal (so not part of the dt-bindings) property
used by dwc3 platform code to indicate that the phy needs to do
charger-detection.
Changes by Hans de Goede:
- Use "linux,phy_charger_detect" property to enable charger-detect
- Switch from a linear flow to a state-machine, with retries on
ulpi communication errors
- Use SW_CONTROL bit to disable the FSM when detection is finished
- Do a phy-reset on disconnect to work around the phy often refusing
ulpi_read()/_write() commands after a disconnect
- Use power_supply_reg_notifier() for Vbus monitoring
- Export the detection result through a power_supply class device
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-10-hdegoede@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to the comment of the function phy_mipi_dphy_get_default_config(),
it uses minimum D-PHY timings based on MIPI D-PHY specification. They are
derived from the valid ranges specified in Section 6.9, Table 14, Page 41
of the D-PHY specification (v1.2). The table 14 explicitly mentions that
the minimum T-LPX parameter is 50 nanoseconds and the minimum TA-SURE
parameter is T-LPX nanoseconds. Likewise, the kernel doc of the 'lpx' and
'ta_sure' members of struct phy_configure_opts_mipi_dphy mentions that
the minimum values are 50000 picoseconds and @lpx picoseconds respectively.
Also, the function phy_mipi_dphy_config_validate() checks if cfg->lpx is
less than 50000 picoseconds and if cfg->ta_sure is less than cfg->lpx,
which hints the same minimum values.
Without this patch, the function phy_mipi_dphy_get_default_config()
wrongly sets cfg->lpx to 60000 picoseconds and cfg->ta_sure to 2 * cfg->lpx.
So, let's correct them to 50000 picoseconds and cfg->lpx respectively.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: dddc97e823 ("phy: dphy: Add configuration helpers")
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220216071257.1647703-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add "wake on" support for the newer Synopsis based XHCI only controller.
This works on the 72165 and 72164 and newer chips and does not work
on 7216 based systems. Also switch the USB sysclk to a slower clock
on suspend to save additional power in S2. The clock switch will only
save power on the 72165b0 and newer chips and is a nop on older chips.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220215032422.5179-1-f.fainelli@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As Icenowy pointed out, newer manuals (starting with H6) actually
document the register block at offset 0x800 as "HCI controller and PHY
interface", also describe the bits in our "PMU_UNK1" register.
Let's put proper names to those "unknown" variables and symbols.
While we are at it, generalise the existing code by allowing a bitmap
of bits to clear and set, to cover newer SoCs: The A100 and H616 use a
different bit for the SIDDQ control.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220203013558.11490-3-samuel@sholland.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In some cases, a single SerDes instance can be shared between two different
processors, each using a separate link. In these cases, the SerDes
configuration is done in an earlier boot stage. Therefore, add support to
skip reconfiguring, if it is was already configured beforehand.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220128072642.29188-1-a-govindraju@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
