Chipidea core was calling the interrupt handler from non-IRQ context
with interrupts enabled, something which can lead to a deadlock if
there's an actual interrupt trying to take a lock that's already held
(e.g. the controller lock in udc_irq()).
Add a wrapper that can be used to fake interrupts instead of calling the
handler directly.
Fixes: 3ecb3e09b0 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Fixes: 876d4e1e82 ("usb: chipidea: core: add wakeup support for extcon")
Cc: Peter Chen <peter.chen@kernel.org>
Cc: stable@vger.kernel.org # 4.4
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211021083447.20078-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Root-cause:
There is an issue like endpoint is not recognized as primed, when bus
have more pressure and the add dTD tripwire semaphore (ATDTW bit in
USBCMD register) that can cause the controller to ignore a dTD that is
added to a primed endpoint.
This issue observed with the Windows10 host machine.
Workaround:
The software must implement a periodic cycle, and check for each dTD,
if the endpoint is primed. It can do this by reading the corresponding
bits in the ENDPTPRIME and ENDPTSTAT registers. If these bits are read
at 0, the software needs to re-prime the endpoint by writing 1 to the
corresponding bit in the ENDPTPRIME register.
Added conditional revision check of 2.20[CI_REVISION_22].
Link: https://lore.kernel.org/linux-usb/SJ0PR02MB8644CBBA848A0F68323F1AA5D4D99@SJ0PR02MB8644.namprd02.prod.outlook.com/
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Link: https://lore.kernel.org/r/20210913140005.955699-1-piyush.mehta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When passing 'phys' in the devicetree to describe the USB PHY phandle
(which is the recommended way according to
Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt) the
following NULL pointer dereference is observed on i.MX7 and i.MX8MM:
[ 1.489344] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000098
[ 1.498170] Mem abort info:
[ 1.500966] ESR = 0x96000044
[ 1.504030] EC = 0x25: DABT (current EL), IL = 32 bits
[ 1.509356] SET = 0, FnV = 0
[ 1.512416] EA = 0, S1PTW = 0
[ 1.515569] FSC = 0x04: level 0 translation fault
[ 1.520458] Data abort info:
[ 1.523349] ISV = 0, ISS = 0x00000044
[ 1.527196] CM = 0, WnR = 1
[ 1.530176] [0000000000000098] user address but active_mm is swapper
[ 1.536544] Internal error: Oops: 96000044 [#1] PREEMPT SMP
[ 1.542125] Modules linked in:
[ 1.545190] CPU: 3 PID: 7 Comm: kworker/u8:0 Not tainted 5.14.0-dirty #3
[ 1.551901] Hardware name: Kontron i.MX8MM N801X S (DT)
[ 1.557133] Workqueue: events_unbound deferred_probe_work_func
[ 1.562984] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO BTYPE=--)
[ 1.568998] pc : imx7d_charger_detection+0x3f0/0x510
[ 1.573973] lr : imx7d_charger_detection+0x22c/0x510
This happens because the charger functions check for the phy presence
inside the imx_usbmisc_data structure (data->usb_phy), but the chipidea
core populates the usb_phy passed via 'phys' inside 'struct ci_hdrc'
(ci->usb_phy) instead.
This causes the NULL pointer dereference inside imx7d_charger_detection().
Fix it by also searching for 'phys' in case 'fsl,usbphy' is not found.
Tested on a imx7s-warp board.
Fixes: 746f316b75 ("usb: chipidea: introduce imx7d USB charger detection")
Cc: stable@vger.kernel.org
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210921113754.767631-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX8MM cannot detect certain CDP USB HUBs. usbmisc_imx.c driver is not
following CDP timing requirements defined by USB BC 1.2 specification
and section 3.2.4 Detection Timing CDP.
During Primary Detection the i.MX device should turn on VDP_SRC and
IDM_SINK for a minimum of 40ms (TVDPSRC_ON). After a time of TVDPSRC_ON,
the i.MX is allowed to check the status of the D- line. Current
implementation is waiting between 1ms and 2ms, and certain BC 1.2
complaint USB HUBs cannot be detected. Increase delay to 40ms allowing
enough time for primary detection.
During secondary detection the i.MX is required to disable VDP_SRC and
IDM_SNK, and enable VDM_SRC and IDP_SINK for at least 40ms (TVDMSRC_ON).
Current implementation is not disabling VDP_SRC and IDM_SNK, introduce
disable sequence in imx7d_charger_secondary_detection() function.
VDM_SRC and IDP_SINK should be enabled for at least 40ms (TVDMSRC_ON).
Increase delay allowing enough time for detection.
Cc: <stable@vger.kernel.org>
Fixes: 746f316b75 ("usb: chipidea: introduce imx7d USB charger detection")
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Jun Li <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20210614175013.495808-1-breno.lima@nxp.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/usb/chipidea/otg.c:25: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/chipidea/otg.c:78: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/chipidea/otg.c:143: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Cc: Peter Chen <peter.chen@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210526130037.856068-15-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter writes:
Below are main changes for v5.11-rc1:
For Chipidea USB2:
- Add tracepoint support for UDC
- Some tiny improvements
For Cadence USB3
- Add some quirks for host mode, and let host work well at more use cases
* SKIP_PHY_INIT
* Disable BEI
* Enable runtime PM default for i.mx platform
- Some tiny improvements
* tag 'usb-v5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
MAINTAINERS: Add myself as a reviewer for CADENCE USB3 DRD IP DRIVER
usb: chipidea: ci_hdrc_imx: Use of_device_get_match_data()
usb: chipidea: usbmisc_imx: Use of_device_get_match_data()
usb: cdns3: fix NULL pointer dereference on no platform data
usb: chipidea: trace: fix the endian issue
usb: chipidea: add tracepoint support for udc
doc: dt-binding: cdns,usb3: add wakeup-irq
usb: cdns3: imx: enable runtime pm by default
usb: cdns3: add quirk for enable runtime pm by default
usb: cdns3: host: disable BEI support
usb: cdns3: host: add xhci_plat_priv quirk XHCI_SKIP_PHY_INIT
usb: cdns3: host: add .suspend_quirk for xhci-plat.c
usb: cdns3: Rids of duplicate error message
usb: cdns3: Add static to cdns3_gadget_exit function
The retrieval of driver data via of_device_get_match_data() can make
the code simpler.
Use of_device_get_match_data() to simplify the code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The retrieval of driver data via of_device_get_match_data() can make
the code simpler.
Use of_device_get_match_data() to simplify the code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
