Pull SCSI fixes from James Bottomley:
"Four fixes, all in drivers.
Three are small and obvious, the qedi one is a bit larger but also
pretty obvious"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Format log strings only if needed
scsi: scsi_debug: Fix buffer size of REPORT ZONES command
scsi: qedi: Fix cmd_cleanup_cmpl counter mismatch issue
scsi: pm80xx: Do not call scsi_remove_host() in pm8001_alloc()
According to ZBC and SPC specifications, the unit of ALLOCATION LENGTH
field of REPORT ZONES command is byte. However, current scsi_debug
implementation handles it as number of zones to calculate buffer size to
report zones. When the ALLOCATION LENGTH has a large number, this results
in too large buffer size and causes memory allocation failure. Fix the
failure by handling ALLOCATION LENGTH as byte unit.
Link: https://lore.kernel.org/r/20211207010638.124280-1-shinichiro.kawasaki@wdc.com
Fixes: f0d1cf9378 ("scsi: scsi_debug: Add ZBC zone commands")
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull SCSI fixes from James Bottomley:
"Two patches, both in drivers.
One is a fix to FC recovery (lpfc) and the other is an enhancement to
support the Intel Alder Motherboard with the UFS driver which comes
under the -rc exception process for hardware enabling"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: ufs-pci: Add support for Intel ADL
scsi: lpfc: Fix non-recovery of remote ports following an unsolicited LOGO
Calling scsi_remove_host() before scsi_add_host() results in a crash:
BUG: kernel NULL pointer dereference, address: 0000000000000108
RIP: 0010:device_del+0x63/0x440
Call Trace:
device_unregister+0x17/0x60
scsi_remove_host+0xee/0x2a0
pm8001_pci_probe+0x6ef/0x1b90 [pm80xx]
local_pci_probe+0x3f/0x90
We cannot call scsi_remove_host() in pm8001_alloc() because scsi_add_host()
has not been called yet at that point in time.
Function call tree:
pm8001_pci_probe()
|
`- pm8001_pci_alloc()
| |
| `- pm8001_alloc()
| |
| `- scsi_remove_host()
|
`- scsi_add_host()
Link: https://lore.kernel.org/r/20211201041627.1592487-1-ipylypiv@google.com
Fixes: 05c6c029a4 ("scsi: pm80xx: Increase number of supported queues")
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull vhost,virtio,vdpa bugfixes from Michael Tsirkin:
"Misc fixes all over the place.
Revert of virtio used length validation series: the approach taken
does not seem to work, breaking too many guests in the process. We'll
need to do length validation using some other approach"
[ This merge also ends up reverting commit f7a36b03a7 ("vsock/virtio:
suppress used length validation"), which came in through the
networking tree in the meantime, and was part of that whole used
length validation series - Linus ]
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa_sim: avoid putting an uninitialized iova_domain
vhost-vdpa: clean irqs before reseting vdpa device
virtio-blk: modify the value type of num in virtio_queue_rq()
vhost/vsock: cleanup removing `len` variable
vhost/vsock: fix incorrect used length reported to the guest
Revert "virtio_ring: validate used buffer length"
Revert "virtio-net: don't let virtio core to validate used length"
Revert "virtio-blk: don't let virtio core to validate used length"
Revert "virtio-scsi: don't let virtio core to validate used buffer length"
This reverts commit c57911ebfb.
Attempts to validate length in the core did not work out. We'll drop
them for now, so revert the dependent changes in drivers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A commit introduced formal regstration of all Fabric nodes to the SCSI
transport as well as REG/UNREG RPI mailbox requests. The commit introduced
the NLP_RELEASE_RPI flag for rports set in the lpfc_cmpl_els_logo_acc()
routine to help clean up the RPIs. This new code caused the driver to
release the RPI value used for the remote port and marked the RPI invalid.
When the driver later attempted to re-login, it would use the invalid RPI
and the adapter rejected the PLOGI request. As no login occurred, the
devloss timer on the rport expired and connectivity was lost.
This patch corrects the code by removing the snippet that requests the rpi
to be unregistered. This change only occurs on a node that is already
marked to be rediscovered. This puts the code back to its original
behavior, preserving the already-assigned rpi value (registered or not)
which can be used on the re-login attempts.
Link: https://lore.kernel.org/r/20211123165646.62740-1-jsmart2021@gmail.com
Fixes: fe83e3b9b4 ("scsi: lpfc: Fix node handling for Fabric Controller and Domain Controller")
Cc: <stable@vger.kernel.org> # v5.14+
Co-developed-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This fixes an issue added in commit 4edd8cd4e8 ("scsi: core: sysfs: Fix
hang when device state is set via sysfs") where if userspace is requesting
to set the device state to SDEV_RUNNING when the state is already
SDEV_RUNNING, we return -EINVAL instead of count. The commmit above set ret
to count for this case, when it should have set it to 0.
Link: https://lore.kernel.org/r/20211120164917.4924-1-michael.christie@oracle.com
Fixes: 4edd8cd4e8 ("scsi: core: sysfs: Fix hang when device state is set via sysfs")
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For updating the IOC firmware's timestamp with system timestamp, the driver
issues the Mpi26IoUnitControlRequest message. While framing the
Mpi26IoUnitControlRequest, the driver should copy the lower 32 bits of the
current timestamp into IOCParameterValue field and the higher 32 bits into
Reserved7 field.
Link: https://lore.kernel.org/r/20211117123215.25487-1-sreekanth.reddy@broadcom.com
Fixes: f98790c003 ("scsi: mpt3sas: Sync time periodically between driver and firmware")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While determining the SAS address of a drive, the driver checks whether the
handle number is less than the HBA phy count or not. If the handle number
is less than the HBA phy count then driver assumes that this handle belongs
to HBA and hence it assigns the HBA SAS address.
During IOC firmware downgrade operation, if the number of HBA phys is
reduced and the OS drive's device handle drops below the phy count while
determining the drive's SAS address, the driver ends up using the HBA's SAS
address. This leads to a mismatch of drive's SAS address and hence the
driver unregisters the OS drive and the system goes into read-only mode.
Update the IOC's num_phys to the HBA phy count provided by actual loaded
firmware.
Link: https://lore.kernel.org/r/20211117105058.3505-1-sreekanth.reddy@broadcom.com
Fixes: a5e99fda01 ("scsi: mpt3sas: Update hba_port objects after host reset")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While looping over shost's sdev list it is possible that one
of the drives is getting removed and its sas_target object is
freed but its sdev object remains intact.
Consequently, a kernel panic can occur while the driver is trying to access
the sas_address field of sas_target object without also checking the
sas_target object for NULL.
Link: https://lore.kernel.org/r/20211117104909.2069-1-sreekanth.reddy@broadcom.com
Fixes: f92363d123 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following sparse warnings in ufshpb_set_hpb_read_to_upiu():
sparse warnings: (new ones prefixed by >>)
drivers/scsi/ufs/ufshpb.c:335:27: sparse: sparse: cast from restricted __be64
drivers/scsi/ufs/ufshpb.c:335:25: sparse: expected restricted __be64 [usertype] ppn_tmp
drivers/scsi/ufs/ufshpb.c:335:25: sparse: got unsigned long long [usertype]
Link: https://lore.kernel.org/r/20211111222452.384089-1-huobean@gmail.com
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
hba->outstanding_tasks, which is read under host_lock spinlock, tells the
interrupt handler what task management tags are in use by the driver. The
doorbell register bits indicate which tags are in use by the hardware. A
doorbell bit that is 0 is because the bit has yet to be set by the driver,
or because the task is complete. It is only possible to disambiguate the 2
cases, if reading/writing the doorbell register is synchronized with
reading/writing hba->outstanding_tasks.
For that reason, reading REG_UTP_TASK_REQ_DOOR_BELL must be done under
spinlock.
Link: https://lore.kernel.org/r/20211108064815.569494-3-adrian.hunter@intel.com
Fixes: f5ef336fd2 ("scsi: ufs: core: Fix task management completion")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
__ufshcd_issue_tm_cmd() clears req->end_io_data after timing out, which
races with the completion function ufshcd_tmc_handler() which expects
req->end_io_data to have a value.
Note __ufshcd_issue_tm_cmd() and ufshcd_tmc_handler() are already
synchronized using hba->tmf_rqs and hba->outstanding_tasks under the
host_lock spinlock.
It is also not necessary (nor typical) to clear req->end_io_data because
the block layer does it before allocating out requests e.g. via
blk_get_request().
So fix by not clearing it.
Link: https://lore.kernel.org/r/20211108064815.569494-2-adrian.hunter@intel.com
Fixes: f5ef336fd2 ("scsi: ufs: core: Fix task management completion")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This fixes a regression added with:
commit f0f82e2476 ("scsi: core: Fix capacity set to zero after
offlinining device")
The problem is that after iSCSI recovery, iscsid will call into the kernel
to set the dev's state to running, and with that patch we now call
scsi_rescan_device() with the state_mutex held. If the SCSI error handler
thread is just starting to test the device in scsi_send_eh_cmnd() then it's
going to try to grab the state_mutex.
We are then stuck, because when scsi_rescan_device() tries to send its I/O
scsi_queue_rq() calls -> scsi_host_queue_ready() -> scsi_host_in_recovery()
which will return true (the host state is still in recovery) and I/O will
just be requeued. scsi_send_eh_cmnd() will then never be able to grab the
state_mutex to finish error handling.
To prevent the deadlock move the rescan-related code to after we drop the
state_mutex.
This also adds a check for if we are already in the running state. This
prevents extra scans and helps the iscsid case where if the transport class
has already onlined the device during its recovery process then we don't
need userspace to do it again plus possibly block that daemon.
Link: https://lore.kernel.org/r/20211105221048.6541-3-michael.christie@oracle.com
Fixes: f0f82e2476 ("scsi: core: Fix capacity set to zero after offlinining device")
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: lijinlin <lijinlin3@huawei.com>
Cc: Wu Bo <wubo40@huawei.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Wu Bo <wubo40@huawei.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We can race where iscsi_session_recovery_timedout() has woken up the error
handler thread and it's now setting the devices to offline, and
session_recovery_timedout()'s call to scsi_target_unblock() is also trying
to set the device's state to transport-offline. We can then get a mix of
states.
For the case where we can't relogin we want the devices to be in
transport-offline so when we have repaired the connection
__iscsi_unblock_session() can set the state back to running.
Set the device state then call into libiscsi to wake up the error handler.
Link: https://lore.kernel.org/r/20211105221048.6541-2-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
