The design of AMD NTB implementation is such that
NTB primary acts as an endpoint device and NTB
secondary is an endpoint device behind a combination
of Switch Upstream and Switch Downstream. Considering
that, the link status and control register needs to
be accessed differently based on the NTB topology.
So in the case of NTB secondary, we first get the
pointer to the Switch Downstream device for the NTB
device. Then we get the pointer to the Switch Upstream
device. Once we have that, we read the Link Status
and Control register to get the correct status of
link at the secondary.
In the case of NTB primary, simply reading the Link
Status and Control register of the NTB device itself
will suffice.
Suggested-by: Jiasen Lin <linjiasen@hygon.cn>
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Fixes: fce8a7bb5b (PCI-Express Non-Transparent Bridge Support)
Fixes: 282a2feeb9 (NTB: Use DMA Engine to Transmit and Receive)
Fixes: a754a8fcaf (NTB: allocate number transport entries depending on size of ring size)
Fixes: d98ef99e37 (NTB: Clean up QP stats info)
Fixes: e74bfeedad (NTB: Add flow control to the ntb_netdev)
Fixes: 569410ca75 (NTB: Use unique DMA channels for TX and RX)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
ntb_mw_set_trans() should work as ntb_mw_clear_trans() when size == 0 and/or
addr == 0. But error in xlate_pos checking condition prevents this.
Fix the condition to make ntb_mw_clear_trans() working.
Fixes: 87d11e645e (NTB: switchtec_ntb: Add memory window support)
Signed-off-by: Alexander Fomichev <fomichev.ru@gmail.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The correct printk format is %pa or %pap, but not %pa[p].
Fixes: 7f46c8b3a5 ("NTB: ntb_tool: Add full multi-port NTB API support")
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
peer->outbuf is a virtual address which is get by ioremap, it can not
be converted to a physical address by virt_to_page and page_to_phys.
This conversion will result in DMA error, because the destination address
which is converted by page_to_phys is invalid.
This patch save the MMIO address of NTB BARx in perf_setup_peer_mw,
and map the BAR space to DMA address after we assign the DMA channel.
Then fill the destination address of DMA descriptor with this DMA address
to guarantee that the address of memory write requests fall into
memory window of NBT BARx with IOMMU enabled and disabled.
Fixes: 5648e56d03 ("NTB: ntb_perf: Add full multi-port NTB API support")
Signed-off-by: Jiasen Lin <linjiasen@hygon.cn>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The offset of PCIe Capability Header for AMD and HYGON NTB is 0x64,
but the macro which named "AMD_LINK_STATUS_OFFSET" is defined as 0x68.
It is offset of Device Capabilities Reg rather than Link Control Reg.
This code trigger an error in get link statsus:
cat /sys/kernel/debug/ntb_hw_amd/0000:43:00.1/info
LNK STA - 0x8fa1
Link Status - Up
Link Speed - PCI-E Gen 0
Link Width - x0
This patch use pcie_capability_read_dword to get link status.
After fix this issue, we can get link status accurately:
cat /sys/kernel/debug/ntb_hw_amd/0000:43:00.1/info
LNK STA - 0x11030042
Link Status - Up
Link Speed - PCI-E Gen 3
Link Width - x16
Fixes: a1b3695820 ("NTB: Add support for AMD PCI-Express Non-Transparent Bridge")
Signed-off-by: Jiasen Lin <linjiasen@hygon.cn>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Pull NTB update from Jon Mason:
"Just a simple patch to add a new Hygon Device ID to the AMD NTB device
driver"
* tag 'ntb-5.5' of git://github.com/jonmason/ntb:
NTB: Add Hygon Device ID
The AMD new hardware uses BAR23 and BAR45 as memory windows
as compared to previos where BAR1, BAR23 and BAR45 is used
for memory windows.
This patch add support for both AMD hardwares.
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Variable rc is initialized to a value that is never read and it
is re-assigned later. The initialization is redundant and can be
removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
On switchtec_ntb_mw_set_trans() call, when (only) address == 0, it acts as
ntb_mw_clear_trans(). Fix this, since address == 0 and size != 0 is valid
combination for setting translation.
Signed-off-by: Alexander Fomichev <fomichev.ru@gmail.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
second parameter of ntb_peer_mw_get_addr is pointing to wrong memory
window index by passing "peer gidx" instead of "local gidx".
For ex, "local gidx" value is '0' and "peer gidx" value is '1', then
on peer side ntb_mw_set_trans() api is used as below with gidx pointing to
local side gidx which is '0', so memroy window '0' is chosen and XLAT '0'
will be programmed by peer side.
ntb_mw_set_trans(perf->ntb, peer->pidx, peer->gidx, peer->inbuf_xlat,
peer->inbuf_size);
Now, on local side ntb_peer_mw_get_addr() is been used as below with gidx
pointing to "peer gidx" which is '1', so pointing to memory window '1'
instead of memory window '0'.
ntb_peer_mw_get_addr(perf->ntb, peer->gidx, &phys_addr,
&peer->outbuf_size);
So this patch pass "local gidx" as parameter to ntb_peer_mw_get_addr().
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Pull NTB updates from Jon Mason:
"New feature to add support for NTB virtual MSI interrupts, the ability
to test and use this feature in the NTB transport layer.
Also, bug fixes for the AMD and Switchtec drivers, as well as some
general patches"
* tag 'ntb-5.3' of git://github.com/jonmason/ntb: (22 commits)
NTB: Describe the ntb_msi_test client in the documentation.
NTB: Add MSI interrupt support to ntb_transport
NTB: Add ntb_msi_test support to ntb_test
NTB: Introduce NTB MSI Test Client
NTB: Introduce MSI library
NTB: Rename ntb.c to support multiple source files in the module
NTB: Introduce functions to calculate multi-port resource index
NTB: Introduce helper functions to calculate logical port number
PCI/switchtec: Add module parameter to request more interrupts
PCI/MSI: Support allocating virtual MSI interrupts
ntb_hw_switchtec: Fix setup MW with failure bug
ntb_hw_switchtec: Skip unnecessary re-setup of shared memory window for crosslink case
ntb_hw_switchtec: Remove redundant steps of switchtec_ntb_reinit_peer() function
NTB: correct ntb_dev_ops and ntb_dev comment typos
NTB: amd: Silence shift wrapping warning in amd_ntb_db_vector_mask()
ntb_hw_switchtec: potential shift wrapping bug in switchtec_ntb_init_sndev()
NTB: ntb_transport: Ensure qp->tx_mw_dma_addr is initaliazed
NTB: ntb_hw_amd: set peer limit register
NTB: ntb_perf: Clear stale values in doorbell and command SPAD register
NTB: ntb_perf: Disable NTB link after clearing peer XLAT registers
...
Introduce the module parameter 'use_msi' which, when set, uses
MSI interrupts instead of doorbells for each queue pair (QP). The
parameter is only available if NTB MSI support is configured into
the kernel. We also require there to be more than one memory window
(MW) so that an extra one is available to forward the APIC region.
To use MSIs, we request one interrupt per QP and forward the MSI address
and data to the peer using scratch pad registers (SPADS) above the MW
SPADS. (If there are not enough SPADS the MSI interrupt will not be used.)
Once registered, we simply use ntb_msi_peer_trigger and the receiving
ISR simply queues up the rxc_db_work for the queue.
This addition can significantly improve performance of ntb_transport.
In a simple, untuned, apples-to-apples comparision using ntb_netdev
and iperf with switchtec hardware, I see 3.88Gb/s without MSI
interrupts and 14.1Gb/s wit MSI, which is a more than 3x improvement.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Introduce a tool to test NTB MSI interrupts similar to the other
NTB test tools. This tool creates a debugfs directory for each
NTB device with the following files:
port
irqX_occurrences
peerX/port
peerX/count
peerX/trigger
The 'port' file tells the user the local port number and the
'occurrences' files tell the number of local interrupts that
have been received for each interrupt.
For each peer, the 'port' file and the 'count' file tell you the
peer's port number and number of interrupts respectively. Writing
the interrupt number to the 'trigger' file triggers the interrupt
handler for the peer which should increment their corresponding
'occurrences' file. The 'ready' file indicates if a peer is ready,
writing to this file blocks until it is ready.
The module parameter num_irqs can be used to set the number of
local interrupts. By default this is 4. This is only limited by
the number of unused MSI interrupts registered by the hardware
(this will require support of the hardware driver) and there must
be at least 2*num_irqs + 1 spads registers available.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The NTB MSI library allows passing MSI interrupts across a memory
window. This offers similar functionality to doorbells or messages
except will often have much better latency and the client can
potentially use significantly more remote interrupts than typical hardware
provides for doorbells. (Which can be important in high-multiport
setups.)
The library utilizes one memory window per peer and uses the highest
index memory windows. Before any ntb_msi function may be used, the user
must call ntb_msi_init(). It may then setup and tear down the memory
windows when the link state changes using ntb_msi_setup_mws() and
ntb_msi_clear_mws().
The peer which receives the interrupt must call ntb_msim_request_irq()
to assign the interrupt handler (this function is functionally
similar to devm_request_irq()) and the returned descriptor must be
transferred to the peer which can use it to trigger the interrupt.
The triggering peer, once having received the descriptor, can
trigger the interrupt by calling ntb_msi_peer_trigger().
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The kbuild system does not support having multiple source files in
a module if one of those source files has the same name as the module.
Therefore, we must rename ntb.c to core.c, while the module remains
ntb.ko.
This is similar to the way the nvme modules are structured.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Switchtec does not support setting multiple MWs simultaneously. The
driver takes a hardware lock to ensure that two peers are not doing this
simultaneously and it fails if someone else takes the lock. In most
cases, this is fine as clients only setup the MWs once on one side of
the link.
However, there's a race condition when a re-initialization is caused by
a link event. The driver will re-setup the shared memory window
asynchronously and this races with the client setting up it's memory
windows on the link up event.
To fix this we ensure do the entire initialization in a work queue and
signal the client once it's done.
Signed-off-by: Joey Zhang <joey.zhang@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
In case of NTB crosslink topology, the setting of shared memory window in
the virtual partition doesn't reset on peer's reboot. So skip the
unnecessary re-setup of shared memory window for that case.
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When a re-initialization is caused by a link event, the driver will
re-setup the shared memory window. But at that time, the shared memory
is still valid, and it's unnecessary to free, reallocate and then
initialize it again. We only need to reconfigure the hardware
registers. Remove the redundant steps from
switchtec_ntb_reinit_peer() function.
Signed-off-by: Joey Zhang <joey.zhang@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This code triggers a Smatch warning:
drivers/ntb/hw/amd/ntb_hw_amd.c:336 amd_ntb_db_vector_mask()
warn: should '(1 << db_vector)' be a 64 bit type?
I don't think "db_vector" can be higher than 16 so this doesn't affect
runtime, but it's nice to silence the static checker warning and we
might increase "ndev->db_count" in the future.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
