Before commit 86585c6197 ("hwmon: (pwm-fan) stop using legacy
PWM functions and some cleanups") pwm_apply_state() was called
unconditionally in pwm_fan_probe(). In this commit this direct
call was replaced by a call to __set_pwm(ct, MAX_PWM) which
however is a noop if ctx->pwm_value already matches the value to
set.
After probe the fan is supposed to run at full speed, and the
internal driver state suggests it does, but this isn't asserted
and depending on bootloader and pwm low-level driver, the fan
might just be off.
So drop setting pwm_value to MAX_PWM to ensure the check in
__set_pwm doesn't make it exit early and the fan goes on as
intended.
Cc: stable@vger.kernel.org
Fixes: 86585c6197 ("hwmon: (pwm-fan) stop using legacy PWM functions and some cleanups")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211130092212.17783-1-billy_tsai@aspeedtech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per datasheet, SHT4x may need up to 8.2ms for a "high repeatability"
measurement to complete. Attempting to read the result too early
triggers a NAK which then causes an EREMOTEIO error.
This behavior has been confirmed with a logic analyzer while running
the I2C bus at only 40kHz. The low frequency precludes any
signal-integrity issues, which was also confirmed by the absence of
any CRC8 errors. In this configuration, a NAK occurred on any read
that followed the measurement command within less than 8.2ms.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Link: https://lore.kernel.org/r/20211120212849.2300854-2-davidm@egauge.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The first call to nct6775_asuswmi_read() in nct6775_wmi_read_value()
had been passing the full bank+register number instead of just the
lower 8 bits. It didn't end up actually causing problems because the
second argument of that function is a u8 anyway, but it seems
preferable to be explicit about it at the call site (and consistent
with the rest of the code).
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 3fbbfc27f9 ("hwmon: (nct6775) Support access via Asus WMI")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211111025339.27520-1-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The removal function is called regardless of whether
/proc/i8k was created successfully or not, the later
causing a WARN() on module removal.
Fix that by only registering the removal function
if /proc/i8k was created successfully.
Tested on a Inspiron 3505.
Fixes: 039ae58503 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211112171440.59006-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Merge misc updates from Andrew Morton:
"257 patches.
Subsystems affected by this patch series: scripts, ocfs2, vfs, and
mm (slab-generic, slab, slub, kconfig, dax, kasan, debug, pagecache,
gup, swap, memcg, pagemap, mprotect, mremap, iomap, tracing, vmalloc,
pagealloc, memory-failure, hugetlb, userfaultfd, vmscan, tools,
memblock, oom-kill, hugetlbfs, migration, thp, readahead, nommu, ksm,
vmstat, madvise, memory-hotplug, rmap, zsmalloc, highmem, zram,
cleanups, kfence, and damon)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (257 commits)
mm/damon: remove return value from before_terminate callback
mm/damon: fix a few spelling mistakes in comments and a pr_debug message
mm/damon: simplify stop mechanism
Docs/admin-guide/mm/pagemap: wordsmith page flags descriptions
Docs/admin-guide/mm/damon/start: simplify the content
Docs/admin-guide/mm/damon/start: fix a wrong link
Docs/admin-guide/mm/damon/start: fix wrong example commands
mm/damon/dbgfs: add adaptive_targets list check before enable monitor_on
mm/damon: remove unnecessary variable initialization
Documentation/admin-guide/mm/damon: add a document for DAMON_RECLAIM
mm/damon: introduce DAMON-based Reclamation (DAMON_RECLAIM)
selftests/damon: support watermarks
mm/damon/dbgfs: support watermarks
mm/damon/schemes: activate schemes based on a watermarks mechanism
tools/selftests/damon: update for regions prioritization of schemes
mm/damon/dbgfs: support prioritization weights
mm/damon/vaddr,paddr: support pageout prioritization
mm/damon/schemes: prioritize regions within the quotas
mm/damon/selftests: support schemes quotas
mm/damon/dbgfs: support quotas of schemes
...
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc and other tiny driver subsystem
updates for 5.16-rc1.
Loads of things in here, all of which have been in linux-next for a
while with no reported problems (except for one called out below.)
Included are:
- habanana labs driver updates, including dma_buf usage, reviewed and
acked by the dma_buf maintainers
- iio driver update (going through this tree not staging as they
really do not belong going through that tree anymore)
- counter driver updates
- hwmon driver updates that the counter drivers needed, acked by the
hwmon maintainer
- xillybus driver updates
- binder driver updates
- extcon driver updates
- dma_buf module namespaces added (will cause a build error in arm64
for allmodconfig, but that change is on its way through the drm
tree)
- lkdtm driver updates
- pvpanic driver updates
- phy driver updates
- virt acrn and nitr_enclaves driver updates
- smaller char and misc driver updates"
* tag 'char-misc-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (386 commits)
comedi: dt9812: fix DMA buffers on stack
comedi: ni_usb6501: fix NULL-deref in command paths
arm64: errata: Enable TRBE workaround for write to out-of-range address
arm64: errata: Enable workaround for TRBE overwrite in FILL mode
coresight: trbe: Work around write to out of range
coresight: trbe: Make sure we have enough space
coresight: trbe: Add a helper to determine the minimum buffer size
coresight: trbe: Workaround TRBE errata overwrite in FILL mode
coresight: trbe: Add infrastructure for Errata handling
coresight: trbe: Allow driver to choose a different alignment
coresight: trbe: Decouple buffer base from the hardware base
coresight: trbe: Add a helper to pad a given buffer area
coresight: trbe: Add a helper to calculate the trace generated
coresight: trbe: Defer the probe on offline CPUs
coresight: trbe: Fix incorrect access of the sink specific data
coresight: etm4x: Add ETM PID for Kryo-5XX
coresight: trbe: Prohibit trace before disabling TRBE
coresight: trbe: End the AUX handle on truncation
coresight: trbe: Do not truncate buffer on IRQ
coresight: trbe: Fix handling of spurious interrupts
...
Pull hwmon updates from Guenter Roeck:
"New driver:
- Maxim MAX6620
Notable functional enhancements:
- Add Asus WMI support to nct6775 driver, and list boards supporting
it
- Move TMP461 support from tm401 driver to lm90 driver
- Add support for fanX_min, fanX_max and fanX_target to dell-smm
driver, and clean it up while doing so
- Extend mlxreg-fan driver to support multiple cooling devices and
multiple PWM channels. Also increase number of supported fan
tachometers.
- Add a new customer ID (for ASRock) to nct6683 driver
- Make temperature/voltage sensors on nct7802 configurable
- Add mfg_id debugfs entry to pmbus/ibm-cffps driver
- Support configurable sense resistor values in pmbus/lm25066, and
fix various coefficients
- Use generic notification mechanism in raspberrypi driver
Notable cleanups:
- Convert various devicetree bindings to dtschema, and add missing
bindings
- Convert i5500_temp and tmp103 drivers to
devm_hwmon_device_register_with_info
- Clean up non-bool "valid" data fields
- Improve devicetree configurability for tmp421 driver"
* tag 'hwmon-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (73 commits)
hwmon: (nct7802) Add of_node_put() before return
hwmon: (tmp401) Drop support for TMP461
hwmon: (lm90) Add basic support for TI TMP461
hwmon: (lm90) Introduce flag indicating extended temperature support
hwmon: (nct6775) add ProArt X570-CREATOR WIFI.
hwmon: (nct7802) Make temperature/voltage sensors configurable
dt-bindings: hwmon: Add nct7802 bindings
hwmon: (dell-smm) Speed up setting of fan speed
hwmon: (dell-smm) Add comment explaining usage of i8k_config_data[]
hwmon: (dell-smm) Return -ENOIOCTLCMD instead of -EINVAL
hwmon: (dell-smm) Use strscpy_pad()
hwmon: (dell-smm) Sort includes in alphabetical order
hwmon: (tmp421) Add of_node_put() before return
hwmon: (max31722) Warn about failure to put device in stand-by in .remove()
hwmon: (acpi_power_meter) Use acpi_bus_get_acpi_device()
hwmon: (dell-smm) Add support for fanX_min, fanX_max and fanX_target
dt-bindings: hwmon: allow specifying channels for tmp421
hwmon: (tmp421) ignore non-channel related DT nodes
hwmon: (tmp421) update documentation
hwmon: (tmp421) support HWMON_T_ENABLE
...
Now that we have all the shared memory region information populated in
the pcc_mbox_chan, let us propagate the pointer to the same as the
return value to pcc_mbox_request channel.
This eliminates the need for the individual users of PCC mailbox to
parse the PCCT subspace entries and fetch the shmem information. This
also eliminates the need for PCC mailbox controller to set con_priv to
PCCT subspace entries. This is required as con_priv is private to the
controller driver to attach private data associated with the channel and
not meant to be used by the mailbox client/users.
Let us convert all the users of pcc_mbox_{request,free}_channel to use
new interface.
Cc: Jean Delvare <jdelvare@suse.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
TMP461 is almost identical to TMP451, which is already supported by the
lm90 driver. At the same time, unlike other sensors from the TMP401
compatible series, it only supports 8-bit temperature read operations,
and it supports negative temperatures when configured for its default
temperature range, and it supports a temperature offset register.
Supporting this chip in the tmp401 driver adds unnecessary complexity.
Remove its support from this driver and support the chip with the lm90
driver instead.
Fixes: 24333ac26d ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TMP461 is almost identical to TMP451 and was actually detected as TMP451
with the existing lm90 driver if its I2C address is 0x4c. Add support
for it to the lm90 driver. At the same time, improve the chip detection
function to at least try to distinguish between TMP451 and TMP461.
As a side effect, this fixes commit 24333ac26d ("hwmon: (tmp401) use
smb word operations instead of 2 smb byte operations"). TMP461 does not
support word operations on temperature registers, which causes bad
temperature readings with the tmp401 driver. The lm90 driver does not
perform word operations on temperature registers and thus does not have
this problem.
Support is listed as basic because TMP461 supports a sensor resolution
of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125
degrees C. Also, the TMP461 supports negative temperatures with its
default temperature range, which is not the case for similar chips
supported by the lm90 and the tmp401 drivers. Those limitations will be
addressed with follow-up patches.
Fixes: 24333ac26d ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A flag indicating extended temperature support makes it easier
to add support for additional chips with this functionality.
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Joel writes:
FSI changes for v5.16
- SBEFIFO usersapce interfaces to perform FFDC (First Failure
Data Capture) and detect timeouts
- A fix to handle multiple messages in flight
* tag 'fsi-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/fsi:
fsi: sbefifo: Use interruptible mutex locking
fsi: sbefifo: Add sysfs file indicating a timeout error
docs: ABI: testing: Document the SBEFIFO timeout interface
hwmon: (occ) Provide the SBEFIFO FFDC in binary sysfs
docs: ABI: testing: Document the OCC hwmon FFDC binary interface
fsi: occ: Store the SBEFIFO FFDC in the user response buffer
fsi: occ: Use a large buffer for responses
hwmon: (occ) Remove sequence numbering and checksum calculation
fsi: occ: Force sequence numbering per OCC
When setting the fan speed, i8k_set_fan() calls i8k_get_fan_status(),
causing an unnecessary SMM call since from the two users of this
function, only i8k_ioctl_unlocked() needs to know the new fan status
while dell_smm_write() ignores the new fan status.
Since SMM calls can be very slow while also making error reporting
difficult for dell_smm_write(), remove the function call from
i8k_set_fan() and call it separately in i8k_ioctl_unlocked().
Tested on a Dell Inspiron 3505.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211021190531.17379-6-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
