Extended SF port attributes to have optional external flag similar to
PCI PF and VF port attributes.
External atttibute is required to generate unique phys_port_name when PF number
and SF number are overlapping between two controllers similar to SR-IOV
VFs.
When a SF is for external controller an example view of external SF
port and config sequence.
On eswitch system:
$ devlink dev eswitch set pci/0033:01:00.0 mode switchdev
$ devlink port show
pci/0033:01:00.0/196607: type eth netdev enP51p1s0f0np0 flavour physical port 0 splittable false
pci/0033:01:00.0/131072: type eth netdev eth0 flavour pcipf controller 1 pfnum 0 external true splittable false
function:
hw_addr 00:00:00:00:00:00
$ devlink port add pci/0033:01:00.0 flavour pcisf pfnum 0 sfnum 77 controller 1
pci/0033:01:00.0/163840: type eth netdev eth1 flavour pcisf controller 1 pfnum 0 sfnum 77 splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
phys_port_name construction:
$ cat /sys/class/net/eth1/phys_port_name
c1pf0sf77
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Saeed Mahameed says:
====================
mlx5 subfunction support
Parav Pandit says:
This patchset introduces support for mlx5 subfunction (SF).
A subfunction is a lightweight function that has a parent PCI function on
which it is deployed. mlx5 subfunction has its own function capabilities
and its own resources. This means a subfunction has its own dedicated
queues(txq, rxq, cq, eq). These queues are neither shared nor stolen from
the parent PCI function.
When subfunction is RDMA capable, it has its own QP1, GID table and rdma
resources neither shared nor stolen from the parent PCI function.
A subfunction has dedicated window in PCI BAR space that is not shared
with the other subfunctions or parent PCI function. This ensures that all
class devices of the subfunction accesses only assigned PCI BAR space.
A Subfunction supports eswitch representation through which it supports tc
offloads. User must configure eswitch to send/receive packets from/to
subfunction port.
Subfunctions share PCI level resources such as PCI MSI-X IRQs with
their other subfunctions and/or with its parent PCI function.
Subfunction support is discussed in detail in RFC [1] and [2].
RFC [1] and extension [2] describes requirements, design and proposed
plumbing using devlink, auxiliary bus and sysfs for systemd/udev
support. Functionality of this patchset is best explained using real
examples further below.
overview:
--------
A subfunction can be created and deleted by a user using devlink port
add/delete interface.
A subfunction can be configured using devlink port function attribute
before its activated.
When a subfunction is activated, it results in an auxiliary device on
the host PCI device where it is deployed. A driver binds to the
auxiliary device that further creates supported class devices.
example subfunction usage sequence:
-----------------------------------
Change device to switchdev mode:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
Add a devlink port of subfunction flavour:
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
Configure mac address of the port function:
$ devlink port function set ens2f0npf0sf88 hw_addr 00:00:00:00:88:88
Now activate the function:
$ devlink port function set ens2f0npf0sf88 state active
Now use the auxiliary device and class devices:
$ devlink dev show
pci/0000:06:00.0
auxiliary/mlx5_core.sf.4
$ ip link show
127: ens2f0np0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 24:8a:07:b3:d1:12 brd ff:ff:ff:ff:ff:ff
altname enp6s0f0np0
129: p0sf88: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 00:00:00:00:88:88 brd ff:ff:ff:ff:ff:ff
$ rdma dev show
43: rdmap6s0f0: node_type ca fw 16.29.0550 node_guid 248a:0703:00b3:d112 sys_image_guid 248a:0703:00b3:d112
44: mlx5_0: node_type ca fw 16.29.0550 node_guid 0000:00ff:fe00:8888 sys_image_guid 248a:0703:00b3:d112
After use inactivate the function:
$ devlink port function set ens2f0npf0sf88 state inactive
Now delete the subfunction port:
$ devlink port del ens2f0npf0sf88
[1] https://lore.kernel.org/netdev/20200519092258.GF4655@nanopsycho/
[2] https://marc.info/?l=linux-netdev&m=158555928517777&w=2
=================
* tag 'mlx5-updates-2021-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Add devlink subfunction port documentation
devlink: Extend devlink port documentation for subfunctions
devlink: Add devlink port documentation
net/mlx5: SF, Port function state change support
net/mlx5: SF, Add port add delete functionality
net/mlx5: E-switch, Add eswitch helpers for SF vport
net/mlx5: E-switch, Prepare eswitch to handle SF vport
net/mlx5: SF, Add auxiliary device driver
net/mlx5: SF, Add auxiliary device support
net/mlx5: Introduce vhca state event notifier
devlink: Support get and set state of port function
devlink: Support add and delete devlink port
devlink: Introduce PCI SF port flavour and port attribute
devlink: Prepare code to fill multiple port function attributes
====================
Link: https://lore.kernel.org/r/20210122193658.282884-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch ASIC has a limited capacity of physical ('flavour physical'
in devlink terminology) ports that it can support. While each system is
brought up with a different number of ports, this number can be
increased via splitting up to the ASIC's limit.
Expose physical ports as a devlink resource so that user space will have
visibility to the maximum number of ports that can be supported and the
current occupancy.
In addition, add a "Generic Resources" section in devlink-resource
documentation so the different drivers will be aligned by the same resource
name when exposing to user space.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
devlink port function can be in active or inactive state.
Allow users to get and set port function's state.
When the port function it activated, its operational state may change
after a while when the device is created and driver binds to it.
Similarly on deactivation flow.
To clearly describe the state of the port function and its device's
operational state in the host system, define state and opstate
attributes.
Example of a PCI SF port which supports a port function:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
$ devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0np0 flavour physical port 0 splittable false
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
pci/0000:08:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show pci/0000:06:00.0/32768
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:88:88 state inactive opstate detached
$ devlink port function set pci/0000:06:00.0/32768 hw_addr 00:00:00:00:88:88 state active
$ devlink port show pci/0000:06:00.0/32768 -jp
{
"port": {
"pci/0000:06:00.0/32768": {
"type": "eth",
"netdev": "ens2f0npf0sf88",
"flavour": "pcisf",
"controller": 0,
"pfnum": 0,
"sfnum": 88,
"external": false,
"splittable": false,
"function": {
"hw_addr": "00:00:00:00:88:88",
"state": "active",
"opstate": "attached"
}
}
}
}
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Extended devlink interface for the user to add and delete a port.
Extend devlink to connect user requests to driver to add/delete
a port in the device.
Driver routines are invoked without holding devlink instance lock.
This enables driver to perform several devlink objects registration,
unregistration such as (port, health reporter, resource etc) by using
existing devlink APIs.
This also helps to uniformly use the code for port unregistration
during driver unload and during port deletion initiated by user.
Examples of add, show and delete commands:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
$ devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0np0 flavour physical port 0 splittable false
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
pci/0000:06:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show pci/0000:06:00.0/32768
pci/0000:06:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ udevadm test-builtin net_id /sys/class/net/eth6
Load module index
Parsed configuration file /usr/lib/systemd/network/99-default.link
Created link configuration context.
Using default interface naming scheme 'v245'.
ID_NET_NAMING_SCHEME=v245
ID_NET_NAME_PATH=enp6s0f0npf0sf88
ID_NET_NAME_SLOT=ens2f0npf0sf88
Unload module index
Unloaded link configuration context.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
A PCI sub-function (SF) represents a portion of the device similar
to PCI VF.
In an eswitch, PCI SF may have port which is normally represented
using a representor netdevice.
To have better visibility of eswitch port, its association with SF,
and its representor netdevice, introduce a PCI SF port flavour.
When devlink port flavour is PCI SF, fill up PCI SF attributes of the
port.
Extend port name creation using PCI PF and SF number scheme on best
effort basis, so that vendor drivers can skip defining their own
scheme.
This is done as cApfNSfM, where A, N and M are controller, PCI PF and
PCI SF number respectively.
This is similar to existing naming for PCI PF and PCI VF ports.
An example view of a PCI SF port:
$ devlink port show pci/0000:06:00.0/32768
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:88:88 state active opstate attached
$ devlink port show pci/0000:06:00.0/32768 -jp
{
"port": {
"pci/0000:06:00.0/32768": {
"type": "eth",
"netdev": "ens2f0npf0sf88",
"flavour": "pcisf",
"controller": 0,
"pfnum": 0,
"sfnum": 88,
"splittable": false,
"function": {
"hw_addr": "00:00:00:00:88:88",
"state": "active",
"opstate": "attached"
}
}
}
}
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add a packet trap to report packets that were dropped due to a
blackhole nexthop.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When performing a flash update via devlink, device drivers may inform
user space of status updates via
devlink_flash_update_(begin|end|timeout|status)_notify functions.
It is expected that drivers do not send any status notifications unless
they send a begin and end message. If a driver sends a status
notification without sending the appropriate end notification upon
finishing (regardless of success or failure), the current implementation
of the devlink userspace program can get stuck endlessly waiting for the
end notification that will never come.
The current ice driver implementation may send such a status message
without the appropriate end notification in rare cases.
Fixing the ice driver is relatively simple: we just need to send the
begin_notify at the start of the function and always send an end_notify
no matter how the function exits.
Rather than assuming driver authors will always get this right in the
future, lets just fix the API so that it is not possible to get wrong.
Make devlink_flash_update_begin_notify and
devlink_flash_update_end_notify static, and call them in devlink.c core
code. Always send the begin_notify just before calling the driver's
flash_update routine. Always send the end_notify just after the routine
returns regardless of success or failure.
Doing this makes the status notification easier to use from the driver,
as it no longer needs to worry about catching failures and cleaning up
by calling devlink_flash_update_end_notify. It is now no longer possible
to do the wrong thing in this regard. We also save a couple of lines of
code in each driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All drivers which implement the devlink flash update support, with the
exception of netdevsim, use either request_firmware or
request_firmware_direct to locate the firmware file. Rather than having
each driver do this separately as part of its .flash_update
implementation, perform the request_firmware within net/core/devlink.c
Replace the file_name parameter in the struct devlink_flash_update_params
with a pointer to the fw object.
Use request_firmware rather than request_firmware_direct. Although most
Linux distributions today do not have the fallback mechanism
implemented, only about half the drivers used the _direct request, as
compared to the generic request_firmware. In the event that
a distribution does support the fallback mechanism, the devlink flash
update ought to be able to use it to provide the firmware contents. For
distributions which do not support the fallback userspace mechanism,
there should be essentially no difference between request_firmware and
request_firmware_direct.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The enable_remote_dev_reset devlink param flags that the host admin
allows device resets that can be initiated by other hosts. This
parameter is useful for setups where a device is shared by different
hosts, such as multi-host setup. Once the user set this parameter to
false, the driver should NACK any attempt to reset the device while the
driver is loaded.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add remote reload stats to hold the history of actions performed due
devlink reload commands initiated by remote host. For example, in case
firmware activation with reset finished successfully but was initiated
by remote host.
The function devlink_remote_reload_actions_performed() is exported to
enable drivers update on remote reload actions performed as it was not
initiated by their own devlink instance.
Expose devlink remote reload stats to the user through devlink dev get
command.
Examples:
$ devlink dev show
pci/0000:82:00.0:
stats:
reload:
driver_reinit 2 fw_activate 1 fw_activate_no_reset 0
remote_reload:
driver_reinit 0 fw_activate 0 fw_activate_no_reset 0
pci/0000:82:00.1:
stats:
reload:
driver_reinit 1 fw_activate 0 fw_activate_no_reset 0
remote_reload:
driver_reinit 1 fw_activate 1 fw_activate_no_reset 0
$ devlink dev show -jp
{
"dev": {
"pci/0000:82:00.0": {
"stats": {
"reload": {
"driver_reinit": 2,
"fw_activate": 1,
"fw_activate_no_reset": 0
},
"remote_reload": {
"driver_reinit": 0,
"fw_activate": 0,
"fw_activate_no_reset": 0
}
}
},
"pci/0000:82:00.1": {
"stats": {
"reload": {
"driver_reinit": 1,
"fw_activate": 0,
"fw_activate_no_reset": 0
},
"remote_reload": {
"driver_reinit": 1,
"fw_activate": 1,
"fw_activate_no_reset": 0
}
}
}
}
}
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add reload stats to hold the history per reload action type and limit.
For example, the number of times fw_activate has been performed on this
device since the driver module was added or if the firmware activation
was performed with or without reset.
Add devlink notification on stats update.
Expose devlink reload stats to the user through devlink dev get command.
Examples:
$ devlink dev show
pci/0000:82:00.0:
stats:
reload:
driver_reinit 2 fw_activate 1 fw_activate_no_reset 0
pci/0000:82:00.1:
stats:
reload:
driver_reinit 1 fw_activate 0 fw_activate_no_reset 0
$ devlink dev show -jp
{
"dev": {
"pci/0000:82:00.0": {
"stats": {
"reload": {
"driver_reinit": 2,
"fw_activate": 1,
"fw_activate_no_reset": 0
}
}
},
"pci/0000:82:00.1": {
"stats": {
"reload": {
"driver_reinit": 1,
"fw_activate": 0,
"fw_activate_no_reset": 0
}
}
}
}
}
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add reload limit to demand restrictions on reload actions.
Reload limits supported:
no_reset: No reset allowed, no down time allowed, no link flap and no
configuration is lost.
By default reload limit is unspecified and so no constraints on reload
actions are required.
Some combinations of action and limit are invalid. For example, driver
can not reinitialize its entities without any downtime.
The no_reset reload limit will have usecase in this patchset to
implement restricted fw_activate on mlx5.
Have the uapi parameter of reload limit ready for future support of
multiselection.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add devlink reload action to allow the user to request a specific reload
action. The action parameter is optional, if not specified then devlink
driver re-init action is used (backward compatible).
Note that when required to do firmware activation some drivers may need
to reload the driver. On the other hand some drivers may need to reset
the firmware to reinitialize the driver entities. Therefore, the devlink
reload command returns the actions which were actually performed.
Reload actions supported are:
driver_reinit: driver entities re-initialization, applying devlink-param
and devlink-resource values.
fw_activate: firmware activate.
command examples:
$devlink dev reload pci/0000:82:00.0 action driver_reinit
reload_actions_performed:
driver_reinit
$devlink dev reload pci/0000:82:00.0 action fw_activate
reload_actions_performed:
driver_reinit fw_activate
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow regions to be registered to a devlink port. The same netlink API
is used, but the port index is provided to indicate when a region is a
port region as opposed to a device region.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new devlink callback, .trap_group_action_set(), which can be used
by device drivers which do not support controlling the action (drop,
trap) on each trap but rather on the entire group trap.
If this new callback is populated, it will take precedence over the
.trap_action_set() callback when the user requests a change of all the
traps in a group.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add parser error drop packet traps, so that capable device driver could
register them with devlink. The new packet trap group holds any drops of
packets which were marked by the device as erroneous during header
parsing. Add documentation for every added packet trap and packet trap
group.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, devlink called into drop monitor in order to report hardware
originated drops / exceptions. devlink intentionally filtered control
packets and did not pass them to drop monitor as they were not dropped
by the underlying hardware.
Now drop monitor registers its probe on a generic 'devlink_trap_report'
tracepoint and should therefore perform this filtering itself instead of
having devlink do that.
Add the trap type as metadata and have drop monitor ignore control
packets.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a tracepoint for trap reports so that drop monitor could register
its probe on it. Use trace_devlink_trap_report_enabled() to avoid
wasting cycles setting the trap metadata if the tracepoint is not
enabled.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sections of device flash may contain settings or device identifying
information. When performing a flash update, it is generally expected
that these settings and identifiers are not overwritten.
However, it may sometimes be useful to allow overwriting these fields
when performing a flash update. Some examples include, 1) customizing
the initial device config on first programming, such as overwriting
default device identifying information, or 2) reverting a device
configuration to known good state provided in the new firmware image, or
3) in case it is suspected that current firmware logic for managing the
preservation of fields during an update is broken.
Although some devices are able to completely separate these types of
settings and fields into separate components, this is not true for all
hardware.
To support controlling this behavior, a new
DEVLINK_ATTR_FLASH_UPDATE_OVERWRITE_MASK is defined. This is an
nla_bitfield32 which will define what subset of fields in a component
should be overwritten during an update.
If no bits are specified, or of the overwrite mask is not provided, then
an update should not overwrite anything, and should maintain the
settings and identifiers as they are in the previous image.
If the overwrite mask has the DEVLINK_FLASH_OVERWRITE_SETTINGS bit set,
then the device should be configured to overwrite any of the settings in
the requested component with settings found in the provided image.
Similarly, if the DEVLINK_FLASH_OVERWRITE_IDENTIFIERS bit is set, the
device should be configured to overwrite any device identifiers in the
requested component with the identifiers from the image.
Multiple overwrite modes may be combined to indicate that a combination
of the set of fields that should be overwritten.
Drivers which support the new overwrite mask must set the
DEVLINK_SUPPORT_FLASH_UPDATE_OVERWRITE_MASK in the
supported_flash_update_params field of their devlink_ops.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink core recently gained support for checking whether the driver
supports a flash_update parameter, via `supported_flash_update_params`.
However, parameters are specified as function arguments. Adding a new
parameter still requires modifying the signature of the .flash_update
callback in all drivers.
Convert the .flash_update function to take a new `struct
devlink_flash_update_params` instead. By using this structure, and the
`supported_flash_update_params` bit field, a new parameter to
flash_update can be added without requiring modification to existing
drivers.
As before, all parameters except file_name will require driver opt-in.
Because file_name is a necessary field to for the flash_update to make
sense, no "SUPPORTED" bitflag is provided and it is always considered
valid. All future additional parameters will require a new bit in the
supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing .flash_update, drivers which do not support
per-component update are manually checking the component parameter to
verify that it is NULL. Without this check, the driver might accept an
update request with a component specified even though it will not honor
such a request.
Instead of having each driver check this, move the logic into
net/core/devlink.c, and use a new `supported_flash_update_params` field
in the devlink_ops. Drivers which will support per-component update must
now specify this by setting DEVLINK_SUPPORT_FLASH_UPDATE_COMPONENT in
the supported_flash_update_params in their devlink_ops.
This helps ensure that drivers do not forget to check for a NULL
component if they do not support per-component update. This also enables
a slightly better error message by enabling the core stack to set the
netlink bad attribute message to indicate precisely the unsupported
attribute in the message.
Going forward, any new additional parameter to flash update will require
a bit in the supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Cc: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the region to be snapshotted to the function performing the
snapshot. This allows one function to operate on numerous regions.
v4:
Add missing kerneldoc for ICE
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
