A problem was reported on CoachZ devices where the display wouldn't come
up, or it would be distorted. It turns out that the PLL code here wasn't
getting called once dsi_pll_10nm_vco_recalc_rate() started returning the
same exact frequency, down to the Hz, that the bootloader was setting
instead of 0 when the clk was registered with the clk framework.
After commit 001d8dc338 ("drm/msm/dsi: remove temp data from global
pll structure") we use a hardcoded value for the parent clk frequency,
i.e. VCO_REF_CLK_RATE, and we also hardcode the value for FRAC_BITS,
instead of getting it from the config structure. This combination of
changes to the recalc function allows us to properly calculate the
frequency of the PLL regardless of whether or not the PLL has been
clk_prepare()d or clk_set_rate()d. That's a good improvement.
Unfortunately, this means that now we won't call down into the PLL clk
driver when we call clk_set_rate() because the frequency calculated in
the framework matches the frequency that is set in hardware. If the rate
is the same as what we want it should be OK to not call the set_rate PLL
op. The real problem is that the prepare op in this driver uses a
private struct member to stash away the vco frequency so that it can
call the set_rate op directly during prepare. Once the set_rate op is
never called because recalc_rate told us the rate is the same, we don't
set this private struct member before the prepare op runs, so we try to
call the set_rate function directly with a frequency of 0. This
effectively kills the PLL and configures it for a rate that won't work.
Calling set_rate from prepare is really quite bad and will confuse any
downstream clks about what the rate actually is of their parent. Fixing
that will be a rather large change though so we leave that to later.
For now, let's stash away the rate we calculate during recalc so that
the prepare op knows what frequency to set, instead of 0. This way
things keep working and the display can enable the PLL properly. In the
future, we should remove that code from the prepare op so that it
doesn't even try to call the set rate function.
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Fixes: 001d8dc338 ("drm/msm/dsi: remove temp data from global pll structure")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210608195519.125561-1-swboyd@chromium.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
This patch eliminates the following smatch warning:
drivers/gpu/drm/drm_auth.c:320 drm_master_release() warn: unlocked access 'master' (line 318) expected lock '&dev->master_mutex'
The 'file_priv->master' field should be protected by the mutex lock to
'&dev->master_mutex'. This is because other processes can concurrently
modify this field and free the current 'file_priv->master'
pointer. This could result in a use-after-free error when 'master' is
dereferenced in subsequent function calls to
'drm_legacy_lock_master_cleanup()' or to 'drm_lease_revoke()'.
An example of a scenario that would produce this error can be seen
from a similar bug in 'drm_getunique()' that was reported by Syzbot:
https://syzkaller.appspot.com/bug?id=148d2f1dfac64af52ffd27b661981a540724f803
In the Syzbot report, another process concurrently acquired the
device's master mutex in 'drm_setmaster_ioctl()', then overwrote
'fpriv->master' in 'drm_new_set_master()'. The old value of
'fpriv->master' was subsequently freed before the mutex was unlocked.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210609092119.173590-1-desmondcheongzx@gmail.com
The calclulation of how many bytes we stuff into the
DSI pipeline for video mode panels is off by three
orders of magnitude because we did not account for the
fact that the DRM mode clock is in kilohertz rather
than hertz.
This used to be:
drm_mode_vrefresh(mode) * mode->htotal * mode->vtotal
which would become for example for s6e63m0:
60 x 514 x 831 = 25628040 Hz, but mode->clock is
25628 as it is in kHz.
This affects only the Samsung GT-I8190 "Golden" phone
right now since it is the only MCDE device with a video
mode display.
Curiously some specimen work with this code and wild
settings in the EOL and empty packets at the end of the
display, but I have noticed an eeire flicker until now.
Others were not so lucky and got black screens.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Fixes: 920dd1b142 ("drm/mcde: Use mode->clock instead of reverse calculating it from the vrefresh")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20210608213318.3897858-1-linus.walleij@linaro.org
Update CP_PROTECT register programming based on downstream.
A6XX_PROTECT_RW is renamed to A6XX_PROTECT_NORDWR to make things aligned
and also be more clear about what it does.
Note that this required switching to use the CP_ALWAYS_ON_COUNTER as the
GMU counter is not accessible from the cmdstream. Which also means
using the CPU counter for the msm_gpu_submit_flush() tracepoint (as
catapult depends on being able to compare this to the start/end values
captured in cmdstream). This may need to be revisited when IFPC is
enabled.
Also, compared to downstream, this opens up CP_PERFCTR_CP_SEL as the
userspace performance tooling (fdperf and pps-producer) expect to be
able to configure the CP counters.
Fixes: 4b565ca5a2 ("drm/msm: Add A6XX device support")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Akhil P Oommen <akhilpo@codeaurora.org>
Link: https://lore.kernel.org/r/20210513171431.18632-5-jonathan@marek.ca
[switch to CP_ALWAYS_ON_COUNTER, open up CP_PERFCNTR_CP_SEL, and spiff
up commit msg]
Signed-off-by: Rob Clark <robdclark@chromium.org>
I met a gpu addr bug recently and the kernel log
tells me the pc is memcpy/memset and link register is
radeon_uvd_resume.
As we know, in some architectures, optimized memcpy/memset
may not work well on device memory. Trival memcpy_toio/memset_io
can fix this problem.
BTW, amdgpu has already done it in:
commit ba0b2275a6 ("drm/amdgpu: use memcpy_to/fromio for UVD fw upload"),
that's why it has no this issue on the same gpu and platform.
Signed-off-by: Chen Li <chenli@uniontech.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It will cause error when alloc memory larger than 128KB in
amdgpu_bo_create->kzalloc. So it needs to switch kzalloc to kvzalloc.
Call Trace:
alloc_pages_current+0x6a/0xe0
kmalloc_order+0x32/0xb0
kmalloc_order_trace+0x1e/0x80
__kmalloc+0x249/0x2d0
amdgpu_bo_create+0x102/0x500 [amdgpu]
? xas_create+0x264/0x3e0
amdgpu_bo_create_vm+0x32/0x60 [amdgpu]
amdgpu_vm_pt_create+0xf5/0x260 [amdgpu]
amdgpu_vm_init+0x1fd/0x4d0 [amdgpu]
Signed-off-by: Changfeng <Changfeng.Zhu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In vc4_atomic_commit_tail() we iterate of the set of old CRTCs, and
attempt to wait on any channels which are still in use. When we iterate
over the CRTCs, we have:
* `i` - the index of the CRTC
* `channel` - the channel a CRTC is using
When we check the channel state, we consult:
old_hvs_state->fifo_state[channel].in_use
... but when we wait for the channel, we erroneously wait on:
old_hvs_state->fifo_state[i].pending_commit
... rather than:
old_hvs_state->fifo_state[channel].pending_commit
... and this bogus access has been observed to result in boot-time hangs
on some arm64 configurations, and can be detected using KASAN. FIx this
by using the correct index.
I've tested this on a Raspberry Pi 3 model B v1.2 with KASAN.
Trimmed KASAN splat:
| ==================================================================
| BUG: KASAN: slab-out-of-bounds in vc4_atomic_commit_tail+0x1cc/0x910
| Read of size 8 at addr ffff000007360440 by task kworker/u8:0/7
| CPU: 2 PID: 7 Comm: kworker/u8:0 Not tainted 5.13.0-rc3-00009-g694c523e7267 #3
|
| Hardware name: Raspberry Pi 3 Model B (DT)
| Workqueue: events_unbound deferred_probe_work_func
| Call trace:
| dump_backtrace+0x0/0x2b4
| show_stack+0x1c/0x30
| dump_stack+0xfc/0x168
| print_address_description.constprop.0+0x2c/0x2c0
| kasan_report+0x1dc/0x240
| __asan_load8+0x98/0xd4
| vc4_atomic_commit_tail+0x1cc/0x910
| commit_tail+0x100/0x210
| ...
|
| Allocated by task 7:
| kasan_save_stack+0x2c/0x60
| __kasan_kmalloc+0x90/0xb4
| vc4_hvs_channels_duplicate_state+0x60/0x1a0
| drm_atomic_get_private_obj_state+0x144/0x230
| vc4_atomic_check+0x40/0x73c
| drm_atomic_check_only+0x998/0xe60
| drm_atomic_commit+0x34/0x94
| drm_client_modeset_commit_atomic+0x2f4/0x3a0
| drm_client_modeset_commit_locked+0x8c/0x230
| drm_client_modeset_commit+0x38/0x60
| drm_fb_helper_set_par+0x104/0x17c
| fbcon_init+0x43c/0x970
| visual_init+0x14c/0x1e4
| ...
|
| The buggy address belongs to the object at ffff000007360400
| which belongs to the cache kmalloc-128 of size 128
| The buggy address is located 64 bytes inside of
| 128-byte region [ffff000007360400, ffff000007360480)
| The buggy address belongs to the page:
| page:(____ptrval____) refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x7360
| flags: 0x3fffc0000000200(slab|node=0|zone=0|lastcpupid=0xffff)
| raw: 03fffc0000000200 dead000000000100 dead000000000122 ffff000004c02300
| raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
| page dumped because: kasan: bad access detected
|
| Memory state around the buggy address:
| ffff000007360300: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
| ffff000007360380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
| >ffff000007360400: 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc
| ^
| ffff000007360480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
| ffff000007360500: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
| ==================================================================
Link: https://lore.kernel.org/r/4d0c8318-bad8-2be7-e292-fc8f70c198de@samsung.com
Link: https://lore.kernel.org/linux-arm-kernel/20210607151740.moncryl5zv3ahq4s@gilmour
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Emma Anholt <emma@anholt.net>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Will Deacon <will@kernel.org>
Cc: dri-devel@lists.freedesktop.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210608085513.2069-1-mark.rutland@arm.com
On sunxi boards that use HDMI output, HDMI device probe keeps being
avoided indefinitely with these repeated messages in dmesg:
platform 1ee0000.hdmi: probe deferral - supplier 1ef0000.hdmi-phy
not ready
There's a fwnode_link being created with fw_devlink=on between hdmi
and hdmi-phy nodes, because both nodes have 'compatible' property set.
Fw_devlink code assumes that nodes that have compatible property
set will also have a device associated with them by some driver
eventually. This is not the case with the current sun8i-hdmi
driver.
This commit makes sun8i-hdmi-phy into a proper platform device
and fixes the display pipeline probe on sunxi boards that use HDMI.
More context: https://lkml.org/lkml/2021/5/16/203
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210607085836.2827429-1-megous@megous.com
drm/tegra: Fixes for v5.13-rc5
The most important change here fixes a race condition that causes either
HDA or (more frequently) display to malfunction because they race for
enabling the SOR power domain at probe time.
Other than that, there's a couple of build warnings for issues
introduced in v5.13 as well as some minor fixes, such as reference leak
plugs.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210603144624.788861-1-thierry.reding@gmail.com
