S3C24XX touchscreen driver, originally written by Arnaud Patard and
other contributors. The driver has had substantial testing as well as
a number of tidying up passes done by Ben Dooks, as noted:
- added kernel-doc comments to most of the routines
- removed old code from pre adc framework days
- updated device probe code to use platform id list matching
- cleaned up debug, since printk() now has timestamp feature
- ensure code uses dev_() reporting macros where necessary
- remove ABS_PRESSURE reporting, tslib can be fixed
- ensure timer is removed on driver exit
- move to using dev_pmops for power management
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is a driver for Dynapro serial touchscreen, which used to be
supported in Xorg. The driver needs updated inputattach utility to
initialize serial port and create proper serio device before the
driver will be bound to it.
Signed-off-by: Tias Guns <tias@ulyssis.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The MELPAS MCS-5000 is the touchscreen controller. The overview of this
controller can see at the following website:
http://www.melfas.com/product/product01.asp?k_r=eng_
This driver is tested on s3c6410 NCP board and supports only the i2c
interface.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The touchscreen works in two modes, wait trigger mode and auto-semi
mode. The device starts in wait trigger mode and waits until pressure
is detected, then device sets WT_INT bit and raises an interrupt.
The driver should put the device into auto-semi mode and prepare for
reading first X and then Y coordinates. When coordinate data is ready
the driver sets ADC_INT bit and raises interrupt again.
[dtor@mail.ru: various cleanups]
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds an accelerated driver for Atmel AVR32 AT32AP700X
microprocessors. It uses interrupts on the channel B in the AC97
controller. Thus, offloading the work queue in the wm97xx-ts driver.
The driver has been tested with Atmel AVR32 AT32AP7000 and Wolfson
WM9712 codec.
The driver can also be easily modified to support Atmel AT91 devices, as
AT91 and AVR32 share the same AC97C module.
[Fixed leak of atmel_wm97xx when probe fails. -- broonie]
[dtor@mail.ru: do not report ABS_PRESSURE events when not measuring pressure]
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
[randy.dunlap@oracle.com: don't use bus_id]
[dtor@mail.ru: locking and other fixups]
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch implements accelerated touchscreen support for the Marvell
Zylonite development platform, supporting pen down interrupts and
continuous mode data transfers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support for the built-in touchscreen controller in DA9034
(aka Micco), usually found on platforms with xscale processors.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Wacom W8001 sensor is a sensor device (uses electromagnetic
resonance) and it is interfaced via its serial microcontroller
to the host.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The AT91SAM9RL SoC integrates a Touchscreen Controller which
can trigger ADC conversion periodically.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Dan Liang <dan.liang@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is V2 of the MigoR touch screen driver. The chip we interface to
is unfortunately a custom designed microcontroller speaking some
undocumented protocol over i2c.
The board specific code is expected to register this device as an i2c
chip using struct i2c_board_info [] and i2c_register_board_info().
[dtor@mail.ru: don't enable touchscreen if there are no users]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support for the touchscreen controllers provided by Wolfson
Microelectronics WM97xx series chips in both polled and streaming
modes.
These drivers have been maintained out of tree since 2003. During
that time the driver the primary maintainer was Liam Girdwood and
a number of people have made contributions including Dmitry Baryshkov,
Stanley Cai, Rodolfo Giometti, Russell King, Marc Kleine-Budde,
Ian Molton, Vincent Sanders, Andrew Zabolotny, Graeme Gregory,
Mike Arthur and myself. Apologies to anyone I have omitted.
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Mike Arthur <mike.arthur@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
