If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.
During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.
Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
irq is disabled in xhci_quiesce(called by xhci_halt, with bit:2 cleared
in USBCMD register), but xhci_run(called by usb_add_hcd) re-enable it.
It's possible that you will receive thousands of interrupt requests
after initialization for 2.0 roothub. And you will get a lot of
warning like, "xHCI dying, ignoring interrupt. Shouldn't IRQs be
disabled?". This amount of interrupt requests will cause the entire
system to freeze.
This problem was first found on a device with ASM2142 host controller
on it.
[tidy up old code while moving it, reword header -Mathias]
Cc: stable@kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
Pull ARMv4T/v5 multiplatform support from Arnd Bergmann:
"This series has been 12 years in the making, it mostly finishes the
work that was started with the founding of Linaro to clean up platform
support in the kernel.
The largest change here is a cleanup of the omap1 platform, which is
the final ARM machine type to get converted to the common-clk
subsystem. All the omap1 specific drivers are now made independent of
the mach/*.h headers to allow the platform to be part of a generic
ARMv4/v5 multiplatform kernel.
The last bit that enables this support is still missing here while we
wait for some last dependencies to make it into the mainline kernel
through other subsystems.
The s3c24xx, ixp4xx, iop32x, ep93xx and dove platforms were all almost
at the point of allowing multiplatform kernels, this work gets
completed here along with a few additional cleanup. At the same time,
the s3c24xx and s3c64xx are now deprecated and expected to get removed
in the future.
The PXA and OMAP1 bits are in a separate branch because of
dependencies. Once both branches are merged, only the three Intel
StrongARM platforms (RiscPC, Footbridge/NetWinder and StrongARM1100)
need separate kernels, and there are no plans to include these"
* tag 'arm-multiplatform-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: ixp4xx: Consolidate Kconfig fixing issue
ARM: versatile: Add missing of_node_put in dcscb_init
ARM: config: Refresh IXP4xx config after multiplatform
ARM: omap1: add back omap_set_dma_priority() stub
ARM: omap: fix missing declaration warnings
ARM: omap: fix address space warnings from sparse
ARM: spear: remove include/mach/ subdirectory
ARM: davinci: remove include/mach/ subdirectory
ARM: omap2: remove include/mach/ subdirectory
integrator: remove empty ap_init_early()
ARM: s3c: fix include path
MAINTAINERS: omap1: Add Janusz as an additional maintainer
ARM: omap1: htc_herald: fix typos in comments
ARM: OMAP1: fix typos in comments
ARM: OMAP1: clock: Remove noop code
ARM: OMAP1: clock: Remove unused code
ARM: OMAP1: clock: Fix UART rate reporting algorithm
ARM: OMAP1: clock: Fix early UART rate issues
ARM: OMAP1: Prepare for conversion of OMAP1 clocks to CCF
ARM: omap1: fix build with no SoC selected
...
initcall_debug shows that OHCI controllers take ~60ms to probe on
Rockchip RK3399 systems:
probe of fe3a0000.usb returned 1 after 58941 usecs
A few of these can add up to waste non-trivial amounts of time at boot.
These host controllers don't provide resources to other drivers, so
this shouldn't contribute to exposing race conditions.
Chrome OS kernels have carried this patch on some systems for a while
without issues. Similar patches have been merged for a variety of (e)MMC
host controllers for similar reasons.
[Brian: rewrote commit message, refreshed, but retained dtor's original
authorship ]
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20220518150150.1.Ie8ea0e945a9c15066237014be219eed60066d493@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The support for xHCI controllers with only one roothub, and the code
to defer primary roothub registation until second roothub got merged
to usb-next for 5.19 at the same time.
commit 873f323618 ("xhci: prepare for operation w/o shared hcd")
commit b7a4f9b5d0 ("xhci: Set HCD flag to defer primary roothub
registration")
These got merged in such a way that the flag to defer primary roothub
registration is set even for xHC controllers with just one roothub.
Fix this by setting the defer flag in a codepath taken only if we have
two roothubs
Fixes: 873f323618 ("xhci: prepare for operation w/o shared hcd")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220516094850.19788-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using a private macro for an invalid grant reference use
the common one.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
The bandwidth budget table is introduced to trace ideal bandwidth used
by each INT/ISOC endpoint, but in fact the endpoint may consume more
bandwidth and cause data transfer error, so it's better to leave some
margin. Obviously it's difficult to find the best margin for all cases,
instead take use of the worst-case scenario.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220512064931.31670-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI_RESET_EP_QUIRK was added in 2009 to support prototype xHC
hardware from Fresco Logic that needed an additional configure endpoint
command after a reset endpoint.
That hardware should not have made it to the market.
Now, 13 years later its about time we get rid of it.
quirk was added in commit ac9d8fe7c6 ("USB: xhci: Add quirk for Fresco
Logic xHCI hardware.")
Print a debug message about the removed quirk if against all odds we run
into this controller.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't enable U1 or U2 Link powermanagenet (LPM) states for USB3
devices connected to tier 2 or further hubs.
For unknown reasons we previously only prevented U1.
Be consistent, and prevent both U1/U2 states if tier policy doesn't
allow LPM.
Also check the tier policy a bit earlier, and return if U1/U2 is
not allowed. This avoids unnecessary xhci MEL commands.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'stop endpoint' command timer was started when a 'stop endpoint'
command was added to the command queue.
This can trigger unwanted timeouts if there are several pending commands
in the queue that xHC needs to handle first.
The generic command timer, which was added later than the 'stop endpoint'
timeout timer, times each command currently being handled by xHC hardware.
A timed out stop endpoint command was treated as a more severe issue than
other failed commands, so the separate stop endpoint timer was left
unchanged.
Use the generic command timer for stop endpoint commands. Identify if
the timed out command was a stop endpoint command in the generic handler,
and treat it with the same severity as earlier.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set "HCD_FLAG_DEFER_RH_REGISTER" to hcd->flags in xhci_run() to defer
registering primary roothub in usb_add_hcd() if xhci has two roothubs.
This will make sure both primary roothub and secondary roothub will be
registered along with the second HCD.
This is required for cold plugged USB devices to be detected in certain
PCIe USB cards (like Inateck USB card connected to AM64 EVM or J7200 EVM).
This patch has been added and reverted earier as it triggered a race
in usb device enumeration.
That race is now fixed in 5.16-rc3, and in stable back to 5.4
commit 6cca13de26 ("usb: hub: Fix locking issues with address0_mutex")
commit 6ae6dc22d2 ("usb: hub: Fix usb enumeration issue due to address0
race")
[minor rebase change, and commit message update -Mathias]
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20220510091630.16564-3-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
