When auditing the locking in i915_gem.c (for a prospective change which
I then abandoned), I noticed two places where struct_mutex is not held
across GEM object manipulations that would usually require it.
Since one is in initial setup and the other in driver unload, I'm
guessing the mutex is not required for either; but post a patch in case
it is.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The interface to ->truncate_range is changing very slightly: once "tmpfs:
take control of its truncate_range" has been applied, this can be applied.
For now there is only a slight inefficiency while this remains unapplied,
but it will soon become essential for managing shmem's use of swap.
Change i915_gem_object_truncate() to use shmem_truncate_range() directly:
which should also spare i915 later change if we switch from
inode_operations->truncate_range to file_operations->fallocate.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Soon tmpfs will stop supporting ->readpage and read_cache_page_gfp(): once
"tmpfs: add shmem_read_mapping_page_gfp" has been applied, this patch can
be applied to ease the transition.
Make i915_gem_object_get_pages_gtt() use shmem_read_mapping_page_gfp() in
the one place it's needed; elsewhere use shmem_read_mapping_page(), with
the mapping's gfp_mask properly initialized.
Forget about __GFP_COLD: since tmpfs initializes its pages with memset,
asking for a cold page is counter-productive.
Include linux/shmem_fs.h also in drm_gem.c: with shmem_file_setup() now
declared there too, we shall remove the prototype from linux/mm.h later.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Soon tmpfs will stop supporting ->readpage and read_mapping_page(): once
"tmpfs: add shmem_read_mapping_page_gfp" has been applied, this patch can
be applied to ease the transition.
ttm_tt_swapin() and ttm_tt_swapout() use shmem_read_mapping_page() in
place of read_mapping_page(), since their swap_space has been created with
shmem_file_setup().
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915: save/resume forcewake lock fixes
Revert "drm/i915: Kill GTT mappings when moving from GTT domain"
drm/i915: Apply HWSTAM workaround for BSD ring on SandyBridge
drm/i915: Call intel_enable_plane from i9xx_crtc_mode_set (again)
A voltage value of 0xff01 requires that the driver
look up the max voltage for the board based using the
atom SetVoltage command table.
Setting the proper voltage should fix stability on
some newer asics.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The field is encoded:
0 = 4 banks
1 = 8 banks
2 = 16 banks
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 4a684a4117.
Userland has always been required to set the object's domain to GTT
before using it through a GTT mapping, it's not something that the
kernel is supposed to enforce. (The pagefault support is so that we
can handle multiple mappings without userland having to pin across
them, not so that userland can use GTT after GPU domains without
telling the kernel).
Fixes 19.2% +/- 0.8% (n=6) performance regression in cairo-gl
firefox-talos-gfx on my T420 latop.
Signed-off-by: Keith Packard <keithp@keithp.com>
0xff01 is not an actual voltage value, but a flag
for the driver. If the power state as that value,
skip setting the voltage.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: fix assumption that semaphore dmaobj is valid in x-chan sync
drm/nv50/disp: fix gamma with page flipping overlay turned on
drm/nouveau/pm: Prevent overflow in nouveau_perf_init()
drm/nouveau: fix big-endian switch
Since we were calling the wptr function before checking if the IH was
even enabled, or the GPU wasn't shutdown, we'd get spam in the logs when
the GPU readback 0xffffffff. This reorders things so we return early
in the no IH and GPU shutdown cases.
Reported-and-tested-by: ManDay on #radeon
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is used during phy init to set up the phy for DP. This may
fix DP problems on DCE3.2 cards.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Certain revisions of the vbios on DCE3.2 cards have a bug
in the transmitter control table which prevents duallink from
being enabled properly on some cards. The action switch statement
jumps to the wrong offset for the OUTPUT_ENABLE action. The fix
is to use the ENABLE action rather than the OUTPUT_ENABLE action
on the affected cards. In fixed version of the vbios, both
actions jump to the same offset, so the change should be safe.
Reported-and-tested-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DDX modifies DMA_SEMAPHORE on nv50 in order to implement sync-to-vblank,
things will go very wrong for cross-channel sync after this.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
While parsing the perf table, there is no check if
the num of entries read from the vbios is less than
the currently allocated number.
In case of a buggy vbios this will cause overwriting
of kernel memory, causing aditional problems.
Add a simple check in order to prevent the case
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The failure appeared in dmesg as:
[drm:i915_hangcheck_ring_idle] *ERROR* Hangcheck timer elapsed... blt
ring idle [waiting on 35064155, at 35064155], missed IRQ?
This works around that problem on by making the blitter command
streamer write interrupt state to the Hardware Status Page when a
MI_USER_INTERRUPT command is decoded, which appears to force the seqno
out to memory before the interrupt happens.
v1->v2: Moved to prior interrupt handler installation and RMW flags as
per feedback.
v2->v3: Removed RMW of flags (by anholt)
Cc: stable@kernel.org
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> [v1]
Tested-by: Eric Anholt <eric@anholt.net> [v1,v3]
(incidence of the bug with a testcase went from avg 2/1000 to
0/12651 in the latest test run (plus more for v1))
Tested-by: Kenneth Graunke <kenneth@whitecape.org> [v1]
Tested-by: Robert Hooker <robert.hooker@canonical.com> [v1]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33394
Signed-off-by: Dave Airlie <airlied@redhat.com>
The existing code assumed scratch registers in a number
of places while in most cases we are be using writeback
and events rather than scratch registers.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
DP clock and lanes were not set properly for DP bridges.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Need to set the external transmitter type properly in
AdjustPixelClock to get the properly output.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
