For VLAN-unaware bridging, tag_8021q uses something perhaps a bit too
tied with the sja1105 switch: each port uses the same pvid which is also
used for standalone operation (a unique one from which the source port
and device ID can be retrieved when packets from that port are forwarded
to the CPU). Since each port has a unique pvid when performing
autonomous forwarding, the switch must be configured for Shared VLAN
Learning (SVL) such that the VLAN ID itself is ignored when performing
FDB lookups. Without SVL, packets would always be flooded, since FDB
lookup in the source port's VLAN would never find any entry.
First of all, to make tag_8021q more palatable to switches which might
not support Shared VLAN Learning, let's just use a common VLAN for all
ports that are under the same bridge.
Secondly, using Shared VLAN Learning means that FDB isolation can never
be enforced. But if all ports under the same VLAN-unaware bridge share
the same VLAN ID, it can.
The disadvantage is that the CPU port can no longer perform precise
source port identification for these packets. But at least we have a
mechanism which has proven to be adequate for that situation: imprecise
RX (dsa_find_designated_bridge_port_by_vid), which is what we use for
termination on VLAN-aware bridges.
The VLAN ID that VLAN-unaware bridges will use with tag_8021q is the
same one as we were previously using for imprecise TX (bridge TX
forwarding offload). It is already allocated, it is just a matter of
using it.
Note that because now all ports under the same bridge share the same
VLAN, the complexity of performing a tag_8021q bridge join decreases
dramatically. We no longer have to install the RX VLAN of a newly
joining port into the port membership of the existing bridge ports.
The newly joining port just becomes a member of the VLAN corresponding
to that bridge, and the other ports are already members of it from when
they joined the bridge themselves. So forwarding works properly.
This means that we can unhook dsa_tag_8021q_bridge_{join,leave} from the
cross-chip notifier level dsa_switch_bridge_{join,leave}. We can put
these calls directly into the sja1105 driver.
With this new mode of operation, a port controlled by tag_8021q can have
two pvids whereas before it could only have one. The pvid for standalone
operation is different from the pvid used for VLAN-unaware bridging.
This is done, again, so that FDB isolation can be enforced.
Let tag_8021q manage this by deleting the standalone pvid when a port
joins a bridge, and restoring it when it leaves it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dimitris Michailidis says:
====================
new Fungible Ethernet driver
This patch series contains a new network driver for the Ethernet
functionality of Fungible cards.
It contains two modules. The first one in patch 2 is a library module
that implements some of the device setup, queue managenent, and support
for operating an admin queue. These are placed in a separate module
because the cards provide a number of PCI functions handled by different
types of drivers and all use the same common means to interact with the
device. Each of the drivers will be relying on this library module for
them.
The remaining patches provide the Ethernet driver for the cards.
v2:
- Fix set_pauseparam, remove get_wol, remove module param (Andrew Lunn)
- Fix a register poll loop (Andrew)
- Replace constants defined with 'static const'
- make W=1 C=1 is clean
- Remove devlink FW update (Jakub)
- Remove duplicate ethtool stats covered by structured API (Jakub)
v3:
- Make TLS stats unconditional (Andrew)
- Remove inline from .c (Andrew)
- Replace some ifdef with IS_ENABLED (Andrew)
- Fix build failure on 32b arches (build robot)
- Fix build issue with make O= (Jakub)
v4:
- Fix for newer bpf_warn_invalid_xdp_action() (Jakub)
- Remove 32b dma_set_mask_and_coherent()
v5:
- Make XDP enter/exit non-disruptive to active traffic
- Remove dormant port state
- Style fixes, unused stuff removal (Jakub)
v6:
- When changing queue depth or numbers allocate the new queues
before shutting down the existing ones (Jakub)
v7:
- Convert IRQ bookeeping to use XArray.
- Changes to the numbers of Tx/Rx queues are now incremental and
do not disrupt ongoing traffic.
- Implement .ndo_eth_ioctl instead of .ndo_do_ioctl.
- Replace deprecated irq_set_affinity_hint.
- Remove TLS 1.3 support (Jakub)
- Remove hwtstamp_config.flags check (Jakub)
- Add locking in SR-IOV enable/disable. (Jakub)
v8:
- Remove dropping of <33B packets and the associated counter (Jakub)
- Report CQE size.
- Show last MAC stats when the netdev isn't running (Andrew)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hook up the new driver to configuration and build.
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides the control pieces for kTLS Tx offload, implementinng the
offload operations.
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the driver's data path. Tx handles skbs, XDP, and kTLS, Rx has skbs
and XDP. Also included are Rx and Tx queue creation/tear-down and
tracing.
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink part, which is minimal at this time giving just the driver
name.
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool operations, primarily related to queues and ports, as well
as device statistics.
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first part of the Fungible ethernet driver. It deals with
device probing, net_device creation, and netdev ops.
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fungible cards have a number of different PCI functions and thus
different drivers, all of which use a common method to initialize and
interact with the device. This commit adds a library module that
collects these common mechanisms. They mainly deal with device
initialization, setting up and destroying queues, and operating an admin
queue. A subset of the FW interface is also included here.
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Menglong Dong says:
====================
net: use kfree_skb_reason() for ip/neighbour
In the series "net: use kfree_skb_reason() for ip/udp packet receive",
reasons for skb drops are added to the packet receive process of IP
layer. Link:
https://lore.kernel.org/netdev/20220205074739.543606-1-imagedong@tencent.com/
And in the first patch of this series, skb drop reasons are added to
the packet egress path of IP layer. As kfree_skb() is not used frequent,
I commit these changes at once and didn't create a patch for every
functions that involed. Following functions are handled:
__ip_queue_xmit()
ip_finish_output()
ip_mc_finish_output()
ip6_output()
ip6_finish_output()
ip6_finish_output2()
Following new drop reasons are introduced (what they mean can be seen
in the document of them):
SKB_DROP_REASON_IP_OUTNOROUTES
SKB_DROP_REASON_BPF_CGROUP_EGRESS
SKB_DROP_REASON_IPV6DISABLED
SKB_DROP_REASON_NEIGH_CREATEFAIL
In the 2th and 3th patches, kfree_skb_reason() is used in neighbour
subsystem instead of kfree_skb(). __neigh_event_send() and
arp_error_report() are involed, and following new drop reasons are
introduced:
SKB_DROP_REASON_NEIGH_FAILED
SKB_DROP_REASON_NEIGH_QUEUEFULL
SKB_DROP_REASON_NEIGH_DEAD
Changes since v2:
- fix typo in the 1th patch of 'SKB_DROP_REASON_IPV6DSIABLED' reported
by Roman
Changes since v1:
- introduce SKB_DROP_REASON_NEIGH_CREATEFAIL for some path in the 1th
patch
- introduce SKB_DROP_REASON_NEIGH_DEAD in the 2th patch
- simplify the document for the new drop reasons, as David Ahern
suggested
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When neighbour become invalid or destroyed, neigh_invalidate() will be
called. neigh->ops->error_report() will be called if the neighbour's
state is NUD_FAILED, and seems here is the only use of error_report().
So we can tell that the reason of skb drops in arp_error_report() is
SKB_DROP_REASON_NEIGH_FAILED.
Replace kfree_skb() used in arp_error_report() with kfree_skb_reason().
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() used in __neigh_event_send() with
kfree_skb_reason(). Following drop reasons are added:
SKB_DROP_REASON_NEIGH_FAILED
SKB_DROP_REASON_NEIGH_QUEUEFULL
SKB_DROP_REASON_NEIGH_DEAD
The first two reasons above should be the hot path that skb drops
in neighbour subsystem.
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() which is used in the packet egress path of IP layer
with kfree_skb_reason(). Functions that are involved include:
__ip_queue_xmit()
ip_finish_output()
ip_mc_finish_output()
ip6_output()
ip6_finish_output()
ip6_finish_output2()
Following new drop reasons are introduced:
SKB_DROP_REASON_IP_OUTNOROUTES
SKB_DROP_REASON_BPF_CGROUP_EGRESS
SKB_DROP_REASON_IPV6DISABLED
SKB_DROP_REASON_NEIGH_CREATEFAIL
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
net: dsa: ocelot: phylink updates
This series updates the Ocelot DSA driver for some of the recent
phylink changes. Specifically, we fill in the supported_interfaces
fields, convert to mac_select_pcs and mark the driver as non-legacy.
We do not convert to phylink_generic_validate() as Ocelot has
special support for its rate adapting PCS which makes the generic
validate method unsuitable for this driver.
The three changes mentioned above are implemented in their own
separate patches with one additional cleanup:
1) Populate the supported_interfaces bitmap
2) Remove the now unnecessary interface checks in the validate methods
3) Convert from phylink_set_pcs() to .mac_select_pcs.
4) Mark the driver as non-legacy
Thanks.
RFC -> non-RFC: add reviewed-by/tested-by's, update patch 1 to set the
supported_interfaces bitmap in felix.c rather than the sub-drivers as
requested by Vladimir.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot DSA driver does not make use of the speed, duplex, pause or
advertisement in its phylink_mac_config() implementation, so it can be
marked as a non-legacy driver.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the PCS selection to use mac_select_pcs, which allows the PCS
to perform any validation it needs, and removes the need to set the PCS
in the mac_config() callback, delving into the higher DSA levels to do
so.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the supported interfaces bitmap is populated, phylink will itself
check that the interface mode is present in this bitmap. Drivers no
longer need to perform this check themselves. Remove these checks.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces bitmap for the Ocelot DSA switches.
Since all sub-drivers only support a single interface mode, defined by
ocelot_port->phy_mode, we can handle this in the main driver code
without reference to the sub-driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should be testing the length before fitting into the u8 byte_count.
This is just a sanity check, the MCTP stack should have limited to MTU
which is checked, and we check consistency later in mctp_i2c_xmit().
Found by Smatch
mctp_i2c_header_create() warn: impossible condition
'(hdr->byte_count > 255) => (0-255 > 255)'
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously if an unregister notify handler ran twice (waiting for
netdev to be released) it would print a warning in mctp_unregister()
every subsequent time the unregister notify occured.
Instead we only need to worry about the case where a mctp_ptr is
set on an unknown device type.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently an invalid port throws a WARN_ON warning however invalid
uninitialized values in reg and cpu_port_index are being used later
on. Fix this by returning -EINVAL for an invalid port value.
Addresses clang-scan warnings:
drivers/net/dsa/qca8k.c:1981:3: warning: 2nd function call argument is an
uninitialized value [core.CallAndMessage]
drivers/net/dsa/qca8k.c:1999:9: warning: 2nd function call argument is an
uninitialized value [core.CallAndMessage]
Fixes: 7544b3ff74 ("net: dsa: qca8k: move pcs configuration")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220224220557.147075-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
