Don't allow the TAI-UTC offset of the system clock to be set by adjtimex()
to a value larger than 100000 seconds.
This prevents an overflow in the conversion to int, prevents the CLOCK_TAI
clock from getting too far ahead of the CLOCK_REALTIME clock, and it is
still large enough to allow leap seconds to be inserted at the maximum rate
currently supported by the kernel (once per day) for the next ~270 years,
however unlikely it is that someone can survive a catastrophic event which
slowed down the rotation of the Earth so much.
Reported-by: Weikang shi <swkhack@gmail.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190618154713.20929-1-mlichvar@redhat.com
Pull time fixes from Ingo Molnar:
"A TIA adjtimex interface extension, and a POSIX compliance ABI fix for
timespec64 users"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ntp: Allow TAI-UTC offset to be set to zero
y2038: Make CONFIG_64BIT_TIME unconditional
The ADJ_TAI adjtimex mode sets the TAI-UTC offset of the system clock.
It is typically set by NTP/PTP implementations and it is automatically
updated by the kernel on leap seconds. The initial value is zero (which
applications may interpret as unknown), but this value cannot be set by
adjtimex. This limitation seems to go back to the original "nanokernel"
implementation by David Mills.
Change the ADJ_TAI check to accept zero as a valid TAI-UTC offset in
order to allow setting it back to the initial value.
Fixes: 153b5d054a ("ntp: support for TAI")
Suggested-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: https://lkml.kernel.org/r/20190417084833.7401-1-mlichvar@redhat.com
Emit an audit record every time selected NTP parameters are modified
from userspace (via adjtimex(2) or clock_adjtime(2)). These parameters
may be used to indirectly change system clock, and thus their
modifications should be audited.
Such events will now generate records of type AUDIT_TIME_ADJNTPVAL
containing the following fields:
- op -- which value was adjusted:
- offset -- corresponding to the time_offset variable
- freq -- corresponding to the time_freq variable
- status -- corresponding to the time_status variable
- adjust -- corresponding to the time_adjust variable
- tick -- corresponding to the tick_usec variable
- tai -- corresponding to the timekeeping's TAI offset
- old -- the old value
- new -- the new value
Example records:
type=TIME_ADJNTPVAL msg=audit(1530616044.507:7): op=status old=64 new=8256
type=TIME_ADJNTPVAL msg=audit(1530616044.511:11): op=freq old=0 new=49180377088000
The records of this type will be associated with the corresponding
syscall records.
An overview of parameter changes that can be done via do_adjtimex()
(based on information from Miroslav Lichvar) and whether they are
audited:
__timekeeping_set_tai_offset() -- sets the offset from the
International Atomic Time
(AUDITED)
NTP variables:
time_offset -- can adjust the clock by up to 0.5 seconds per call
and also speed it up or slow down by up to about
0.05% (43 seconds per day) (AUDITED)
time_freq -- can speed up or slow down by up to about 0.05%
(AUDITED)
time_status -- can insert/delete leap seconds and it also enables/
disables synchronization of the hardware real-time
clock (AUDITED)
time_maxerror, time_esterror -- change error estimates used to
inform userspace applications
(NOT AUDITED)
time_constant -- controls the speed of the clock adjustments that
are made when time_offset is set (NOT AUDITED)
time_adjust -- can temporarily speed up or slow down the clock by up
to 0.05% (AUDITED)
tick_usec -- a more extreme version of time_freq; can speed up or
slow down the clock by up to 10% (AUDITED)
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Moore <paul@paul-moore.com>
struct timex is not y2038 safe.
Replace all uses of timex with y2038 safe __kernel_timex.
Note that struct __kernel_timex is an ABI interface definition.
We could define a new structure based on __kernel_timex that
is only available internally instead. Right now, there isn't
a strong motivation for this as the structure is isolated to
a few defined struct timex interfaces and such a structure would
be exactly the same as struct timex.
The patch was generated by the following coccinelle script:
virtual patch
@depends on patch forall@
identifier ts;
expression e;
@@
(
- struct timex ts;
+ struct __kernel_timex ts;
|
- struct timex ts = {};
+ struct __kernel_timex ts = {};
|
- struct timex ts = e;
+ struct __kernel_timex ts = e;
|
- struct timex *ts;
+ struct __kernel_timex *ts;
|
(memset \| copy_from_user \| copy_to_user \)(...,
- sizeof(struct timex))
+ sizeof(struct __kernel_timex))
)
@depends on patch forall@
identifier ts;
identifier fn;
@@
fn(...,
- struct timex *ts,
+ struct __kernel_timex *ts,
...) {
...
}
@depends on patch forall@
identifier ts;
identifier fn;
@@
fn(...,
- struct timex *ts) {
+ struct __kernel_timex *ts) {
...
}
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Cc: linux-alpha@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull y2038 updates from Arnd Bergmann:
"More syscalls and cleanups
This concludes the main part of the system call rework for 64-bit
time_t, which has spread over most of year 2018, the last six system
calls being
- ppoll
- pselect6
- io_pgetevents
- recvmmsg
- futex
- rt_sigtimedwait
As before, nothing changes for 64-bit architectures, while 32-bit
architectures gain another entry point that differs only in the layout
of the timespec structure. Hopefully in the next release we can wire
up all 22 of those system calls on all 32-bit architectures, which
gives us a baseline version for glibc to start using them.
This does not include the clock_adjtime, getrusage/waitid, and
getitimer/setitimer system calls. I still plan to have new versions of
those as well, but they are not required for correct operation of the
C library since they can be emulated using the old 32-bit time_t based
system calls.
Aside from the system calls, there are also a few cleanups here,
removing old kernel internal interfaces that have become unused after
all references got removed. The arch/sh cleanups are part of this,
there were posted several times over the past year without a reaction
from the maintainers, while the corresponding changes made it into all
other architectures"
* tag 'y2038-for-4.21' of ssh://gitolite.kernel.org:/pub/scm/linux/kernel/git/arnd/playground:
timekeeping: remove obsolete time accessors
vfs: replace current_kernel_time64 with ktime equivalent
timekeeping: remove timespec_add/timespec_del
timekeeping: remove unused {read,update}_persistent_clock
sh: remove board_time_init() callback
sh: remove unused rtc_sh_get/set_time infrastructure
sh: sh03: rtc: push down rtc class ops into driver
sh: dreamcast: rtc: push down rtc class ops into driver
y2038: signal: Add compat_sys_rt_sigtimedwait_time64
y2038: signal: Add sys_rt_sigtimedwait_time32
y2038: socket: Add compat_sys_recvmmsg_time64
y2038: futex: Add support for __kernel_timespec
y2038: futex: Move compat implementation into futex.c
io_pgetevents: use __kernel_timespec
pselect6: use __kernel_timespec
ppoll: use __kernel_timespec
signal: Add restore_user_sigmask()
signal: Add set_user_sigmask()
After arch/sh has removed the last reference to these functions,
we can remove them completely and just rely on the 64-bit time_t
based versions. This cleans up a rather ugly use of __weak
functions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Since the subsequent changes will need a TICK_USEC definition
analogous to TICK_NSEC, rename the existing TICK_USEC as
USER_TICK_USEC, update its users and redefine TICK_USEC
accordingly.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code to check the adjtimex() or clock_adjtime() arguments is spread
out across multiple files for presumably only historic reasons. As a
preparatation for a rework to get rid of the use of 'struct timeval'
and 'struct timespec' in there, this moves all the portions into
kernel/time/timekeeping.c and marks them as 'static'.
The warp_clock() function here is not as closely related as the others,
but I feel it still makes sense to move it here in order to consolidate
all callers of timekeeping_inject_offset().
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[jstultz: Whitespace fixup]
Signed-off-by: John Stultz <john.stultz@linaro.org>
ntp is currently hardwired to try and call the rtc set when wall clock
tv_nsec is 0.5 seconds. This historical behaviour works well with certain
PC RTCs, but is not universal to all rtc hardware.
Change how this works by introducing the driver specific concept of
set_offset_nsec, the delay between current wall clock time and the target
time to set (with a 0 tv_nsecs).
For x86-style CMOS set_offset_nsec should be -0.5 s which causes the last
second to be written 0.5 s after it has started.
For compat with the old rtc_set_ntp_time, the value is defaulted to
+ 0.5 s, which causes the next second to be written 0.5s before it starts,
as things were before this patch.
Testing shows many non-x86 RTCs would like set_offset_nsec ~= 0,
so ultimately each RTC driver should set the set_offset_nsec according
to its needs, and non x86 architectures should stop using
update_persistent_clock64 in order to access this feature.
Future patches will revise the drivers as needed.
Since CMOS and RTC now have very different handling they are split
into two dedicated code paths, sharing the support code, and ifdefs
are replaced with IS_ENABLED.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
The function "second_overflow" uses "unsign long"
as its input parameter type which will overflow after
year 2106 on 32bit systems.
Thus this patch replaces it with time64_t type.
While the 64-bit division is expensive, "next_ntp_leap_sec"
has been calculated already, so we can just re-use it in the
TIME_INS/DEL cases, allowing one expensive division per
leapsecond instead of re-doing the divsion once a second after
the leap flag has been set.
Signed-off-by: DengChao <chao.deng@linaro.org>
[jstultz: Tweaked commit message]
Signed-off-by: John Stultz <john.stultz@linaro.org>
The type of static variant "time_reftime" and the call of
get_seconds in ntp are both not y2038 safe.
So change the type of time_reftime to time64_t and replace
get_seconds with __ktime_get_real_seconds.
The local variant "secs" in ntp_update_offset represents
seconds between now and last ntp adjustment, it seems impossible
that this time will last more than 68 years, so keep its type as
"long".
Reviewed-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: DengChao <chao.deng@linaro.org>
[jstultz: Tweaked commit message]
Signed-off-by: John Stultz <john.stultz@linaro.org>
For adjtimex()'s ADJ_SETOFFSET, make sure the tv_usec value is
sane. We might multiply them later which can cause an overflow
and undefined behavior.
This patch introduces new helper functions to simplify the
checking code and adds comments to clarify
Orginally this patch was by Sasha Levin, but I've basically
rewritten it, so he should get credit for finding the issue
and I should get the blame for any mistakes made since.
Also, credit to Richard Cochran for the phrasing used in the
comment for what is considered valid here.
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The sync_cmos_clock has one use of struct timespec, which we want to
eventually replace with timespec64 or similar in the kernel. There
is no way this one can overflow, but the conversion to timespec64
is trivial and has no other dependencies.
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
