Pull networking fixes from David Miller:
1) Fix leak in nl80211 AP start where we leak the ACL memory, from
Johannes Berg.
2) Fix double mutex unlock in mac80211, from Andrei Otcheretianski.
3) Fix RCU stall in ipset, from Jozsef Kadlecsik.
4) Fix devlink locking in devlink_dpipe_table_register, from Madhuparna
Bhowmik.
5) Fix race causing TX hang in ll_temac, from Esben Haabendal.
6) Stale eth hdr pointer in br_dev_xmit(), from Nikolay Aleksandrov.
7) Fix TX hash calculation bounds checking wrt. tc rules, from Amritha
Nambiar.
8) Size netlink responses properly in schedule action code to take into
consideration TCA_ACT_FLAGS. From Jiri Pirko.
9) Fix firmware paths for mscc PHY driver, from Antoine Tenart.
10) Don't register stmmac notifier multiple times, from Aaro Koskinen.
11) Various rmnet bug fixes, from Taehee Yoo.
12) Fix vsock deadlock in vsock transport release, from Stefano
Garzarella.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (61 commits)
net: dsa: mv88e6xxx: Fix masking of egress port
mlxsw: pci: Wait longer before accessing the device after reset
sfc: fix timestamp reconstruction at 16-bit rollover points
vsock: fix potential deadlock in transport->release()
unix: It's CONFIG_PROC_FS not CONFIG_PROCFS
net: rmnet: fix packet forwarding in rmnet bridge mode
net: rmnet: fix bridge mode bugs
net: rmnet: use upper/lower device infrastructure
net: rmnet: do not allow to change mux id if mux id is duplicated
net: rmnet: remove rcu_read_lock in rmnet_force_unassociate_device()
net: rmnet: fix suspicious RCU usage
net: rmnet: fix NULL pointer dereference in rmnet_changelink()
net: rmnet: fix NULL pointer dereference in rmnet_newlink()
net: phy: marvell: don't interpret PHY status unless resolved
mlx5: register lag notifier for init network namespace only
unix: define and set show_fdinfo only if procfs is enabled
hinic: fix a bug of rss configuration
hinic: fix a bug of setting hw_ioctxt
hinic: fix a irq affinity bug
net/smc: check for valid ib_client_data
...
Pull tracing and bootconfig updates:
"Fixes and changes to bootconfig before it goes live in a release.
Change in API of bootconfig (before it comes live in a release):
- Have a magic value "BOOTCONFIG" in initrd to know a bootconfig
exists
- Set CONFIG_BOOT_CONFIG to 'n' by default
- Show error if "bootconfig" on cmdline but not compiled in
- Prevent redefining the same value
- Have a way to append values
- Added a SELECT BLK_DEV_INITRD to fix a build failure
Synthetic event fixes:
- Switch to raw_smp_processor_id() for recording CPU value in preempt
section. (No care for what the value actually is)
- Fix samples always recording u64 values
- Fix endianess
- Check number of values matches number of fields
- Fix a printing bug
Fix of trace_printk() breaking postponed start up tests
Make a function static that is only used in a single file"
* tag 'trace-v5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
bootconfig: Fix CONFIG_BOOTTIME_TRACING dependency issue
bootconfig: Add append value operator support
bootconfig: Prohibit re-defining value on same key
bootconfig: Print array as multiple commands for legacy command line
bootconfig: Reject subkey and value on same parent key
tools/bootconfig: Remove unneeded error message silencer
bootconfig: Add bootconfig magic word for indicating bootconfig explicitly
bootconfig: Set CONFIG_BOOT_CONFIG=n by default
tracing: Clear trace_state when starting trace
bootconfig: Mark boot_config_checksum() static
tracing: Disable trace_printk() on post poned tests
tracing: Have synthetic event test use raw_smp_processor_id()
tracing: Fix number printing bug in print_synth_event()
tracing: Check that number of vals matches number of synth event fields
tracing: Make synth_event trace functions endian-correct
tracing: Make sure synth_event_trace() example always uses u64
Pull Kunit fixes from Shuah Khan:
"This Kselftest kunit update consists of fixes to documentation and
the run-time tool from Brendan Higgins and Heidi Fahim"
* tag 'linux-kselftest-kunit-5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: run kunit_tool from any directory
kunit: test: Improve error messages for kunit_tool when kunitconfig is invalid
Documentation: kunit: fixed sphinx error in code block
Pull Kselftest fixes from Shuah Khan:
- fixes to TIMEOUT failures and out-of-tree compilation compilation
errors from Michael Ellerman.
- declutter git status fix from Christophe Leroy
* tag 'linux-kselftest-5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/rseq: Fix out-of-tree compilation
selftests: Install settings files to fix TIMEOUT failures
selftest/lkdtm: Don't pollute 'git status'
Add a specific test for the crash reported by Phil Sutter and addressed
in the previous patch. The test cases that, in my intention, should
have covered these cases, that is, the ones from the 'concurrency'
section, don't run these sequences tightly enough and spectacularly
failed to catch this.
While at it, define a convenient way to add these kind of tests, by
adding a "reported issues" test section.
It's more convenient, for this particular test, to execute the set
setup in its own function. However, future test cases like this one
might need to call setup functions, and will typically need no tools
other than nft, so allow for this in check_tools().
The original form of the reproducer used here was provided by Phil.
Reported-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Before nftables commit fb9cea50e8b3 ("main: enforce options before
commands"), 'nft list ruleset -a' happened to work, but it's wrong
and won't work anymore. Replace it by 'nft -a list ruleset'.
Reported-by: Chen Yi <yiche@redhat.com>
Fixes: 611973c1e0 ("selftests: netfilter: Introduce tests for sets with range concatenation")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking fixes from David Miller:
1) Limit xt_hashlimit hash table size to avoid OOM or hung tasks, from
Cong Wang.
2) Fix deadlock in xsk by publishing global consumer pointers when NAPI
is finished, from Magnus Karlsson.
3) Set table field properly to RT_TABLE_COMPAT when necessary, from
Jethro Beekman.
4) NLA_STRING attributes are not necessary NULL terminated, deal wiht
that in IFLA_ALT_IFNAME. From Eric Dumazet.
5) Fix checksum handling in atlantic driver, from Dmitry Bezrukov.
6) Handle mtu==0 devices properly in wireguard, from Jason A.
Donenfeld.
7) Fix several lockdep warnings in bonding, from Taehee Yoo.
8) Fix cls_flower port blocking, from Jason Baron.
9) Sanitize internal map names in libbpf, from Toke Høiland-Jørgensen.
10) Fix RDMA race in qede driver, from Michal Kalderon.
11) Fix several false lockdep warnings by adding conditions to
list_for_each_entry_rcu(), from Madhuparna Bhowmik.
12) Fix sleep in atomic in mlx5 driver, from Huy Nguyen.
13) Fix potential deadlock in bpf_map_do_batch(), from Yonghong Song.
14) Hey, variables declared in switch statement before any case
statements are not initialized. I learn something every day. Get
rids of this stuff in several parts of the networking, from Kees
Cook.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (99 commits)
bnxt_en: Issue PCIe FLR in kdump kernel to cleanup pending DMAs.
bnxt_en: Improve device shutdown method.
net: netlink: cap max groups which will be considered in netlink_bind()
net: thunderx: workaround BGX TX Underflow issue
ionic: fix fw_status read
net: disable BRIDGE_NETFILTER by default
net: macb: Properly handle phylink on at91rm9200
s390/qeth: fix off-by-one in RX copybreak check
s390/qeth: don't warn for napi with 0 budget
s390/qeth: vnicc Fix EOPNOTSUPP precedence
openvswitch: Distribute switch variables for initialization
net: ip6_gre: Distribute switch variables for initialization
net: core: Distribute switch variables for initialization
udp: rehash on disconnect
net/tls: Fix to avoid gettig invalid tls record
bpf: Fix a potential deadlock with bpf_map_do_batch
bpf: Do not grab the bucket spinlock by default on htab batch ops
ice: Wait for VF to be reset/ready before configuration
ice: Don't tell the OS that link is going down
ice: Don't reject odd values of usecs set by user
...
The commits introducing 'mlock-random-test'[1], 'map_fiex_noreplace'[2],
and 'thuge-gen'[3] have not added those in the 'run_vmtests' script and
thus the 'run_tests' command of kselftests doesn't run those. This
commit adds those in the script.
'gup_benchmark' and 'transhuge-stress' are also not included in the
'run_vmtests', but this commit does not add those because those are for
performance measurement rather than pass/fail tests.
[1] commit 26b4224d99 ("selftests: expanding more mlock selftest")
[2] commit 91cbacc345 ("tools/testing/selftests/vm/map_fixed_noreplace.c: add test for MAP_FIXED_NOREPLACE")
[3] commit fcc1f2d5dd ("selftests: add a test program for variable huge page sizes in mmap/shmget")
Link: http://lkml.kernel.org/r/20200206085144.29126-1-sj38.park@gmail.com
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Cc: Uladzislau Rezki (Sony) <urezki@gmail.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, bootconfig adds a new value on the existing key to the tail of an
array. But this looks a bit confusing because an admin can easily rewrite
the original value in the same config file.
This rejects the following value re-definition.
key = value1
...
key = value2
You should rewrite value1 to value2 in this case.
Link: http://lkml.kernel.org/r/158227282199.12842.10110929876059658601.stgit@devnote2
Suggested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
[ Fixed spelling of arraies to arrays ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reject if a value node is mixed with subkey node on same
parent key node.
A value node can not co-exist with subkey node under some key
node, e.g.
key = value
key.subkey = another-value
This is not be allowed because bootconfig API is not designed
to handle such case.
Link: http://lkml.kernel.org/r/158220115232.26565.7792340045009731803.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Add bootconfig magic word to the end of bootconfig on initrd
image for indicating explicitly the bootconfig is there.
Also tools/bootconfig treats wrong size or wrong checksum or
parse error as an error, because if there is a bootconfig magic
word, there must be a bootconfig.
The bootconfig magic word is "#BOOTCONFIG\n", 12 bytes word.
Thus the block image of the initrd file with bootconfig is
as follows.
[Initrd][bootconfig][size][csum][#BOOTCONFIG\n]
Link: http://lkml.kernel.org/r/158220112263.26565.3944814205960612841.stgit@devnote2
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Currently if you build with O=... the rseq tests don't build:
$ make O=$PWD/output -C tools/testing/selftests/ TARGETS=rseq
make: Entering directory '/linux/tools/testing/selftests'
...
make[1]: Entering directory '/linux/tools/testing/selftests/rseq'
gcc -O2 -Wall -g -I./ -I../../../../usr/include/ -L./ -Wl,-rpath=./ -shared -fPIC rseq.c -lpthread -o /linux/output/rseq/librseq.so
gcc -O2 -Wall -g -I./ -I../../../../usr/include/ -L./ -Wl,-rpath=./ basic_test.c -lpthread -lrseq -o /linux/output/rseq/basic_test
/usr/bin/ld: cannot find -lrseq
collect2: error: ld returned 1 exit status
This is because the library search path points to the source
directory, not the output.
We can fix it by changing the library search path to $(OUTPUT).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Commit 852c8cbf34 ("selftests/kselftest/runner.sh: Add 45 second
timeout per test") added a 45 second timeout for tests, and also added
a way for tests to customise the timeout via a settings file.
For example the ftrace tests take multiple minutes to run, so they
were given longer in commit b43e78f65b ("tracing/selftests: Turn off
timeout setting").
This works when the tests are run from the source tree. However if the
tests are installed with "make -C tools/testing/selftests install",
the settings files are not copied into the install directory. When the
tests are then run from the install directory the longer timeouts are
not applied and the tests timeout incorrectly.
So add the settings files to TEST_FILES of the appropriate Makefiles
to cause the settings files to be installed using the existing install
logic.
Fixes: 852c8cbf34 ("selftests/kselftest/runner.sh: Add 45 second timeout per test")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Pull Kselftest fixes from Shuah Khan:
"Fixes to build failures and other test bugs"
* tag 'linux-kselftest-5.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: openat2: fix build error on newer glibc
selftests: use LDLIBS for libraries instead of LDFLAGS
selftests: fix too long argument
selftests: allow detection of build failures
Kernel selftests: tpm2: check for tpm support
selftests/ftrace: Have pid filter test use instance flag
selftests: fix spelling mistaked "chaigned" -> "chained"
Alexei Starovoitov says:
====================
pull-request: bpf 2020-02-19
The following pull-request contains BPF updates for your *net* tree.
We've added 10 non-merge commits during the last 10 day(s) which contain
a total of 10 files changed, 93 insertions(+), 31 deletions(-).
The main changes are:
1) batched bpf hashtab fixes from Brian and Yonghong.
2) various selftests and libbpf fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented small fix so that the script changes work directories to the
root of the linux kernel source tree from which kunit.py is run. This
enables the user to run kunit from any working directory. Originally
considered using os.path.join but this is more error prone as we would
have to find all file path usages and modify them accordingly. Using
os.chdir ensures that the entire script is run within /linux.
Signed-off-by: Heidi Fahim <heidifahim@google.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Previous error message for invalid kunitconfig was vague. Added to it so
that it lists invalid fields and prompts for them to be removed. Added
validate_config function returning whether or not this kconfig is valid.
Signed-off-by: Heidi Fahim <heidifahim@google.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The kernel only accepts map names with alphanumeric characters, underscores
and periods in their name. However, the auto-generated internal map names
used by libbpf takes their prefix from the user-supplied BPF object name,
which has no such restriction. This can lead to "Invalid argument" errors
when trying to load a BPF program using global variables.
Fix this by sanitising the map names, replacing any non-allowed characters
with underscores.
Fixes: d859900c4c ("bpf, libbpf: support global data/bss/rodata sections")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200217171701.215215-1-toke@redhat.com
The performance of bpf_redirect() is now roughly the same as that of
bpf_redirect_map(). However, David Ahern pointed out that the header file
has not been updated to reflect this, and still says that a significant
performance increase is possible when using bpf_redirect_map(). Remove this
text from the bpf_redirect_map() description, and reword the description in
bpf_redirect() slightly. Also fix the 'Return' section of the
bpf_redirect_map() documentation.
Fixes: 1d233886dd ("xdp: Use bulking for non-map XDP_REDIRECT and consolidate code paths")
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20200218130334.29889-1-toke@redhat.com
0x11 and 0x12 set the ECN bits based on RFC2474, it would be better to avoid
that. 0x14 and 0x18 would be better and works as well.
Reported-by: Petr Machata <petrm@mellanox.com>
Fixes: 4e867c9a50 ("selftests: forwarding: vxlan_bridge_1d: fix tos value")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This gives us fewer dependencies and shortens build time, fixes up some
hash checking race conditions, and also fixes missing directory creation
that caused issues on massively parallel builds.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 71130f2997 ("vxlan: fix tos value before xmit") we start
strict vxlan xmit tos value by RT_TOS(), which limits the tos value less
than 0x1E. With current value 0x40 the test will failed with "v1: Expected
to capture 10 packets, got 0". So let's choose a smaller tos value for
testing.
Fixes: d417ecf533 ("selftests: forwarding: vxlan_bridge_1d: Add a TOS test")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 2759647247 ("ipv6: fix ECMP route replacement") it is no
longer possible to replace an ECMP-able route by a non ECMP-able route.
For example,
ip route add 2001:db8::1/128 via fe80::1 dev dummy0
ip route replace 2001:db8::1/128 dev dummy0
does not work as expected.
Tweak the replacement logic so that point 3 in the log of the above commit
becomes:
3. If the new route is not ECMP-able, and no matching non-ECMP-able route
exists, replace matching ECMP-able route (if any) or add the new route.
We can now summarize the entire replace semantics to:
When doing a replace, prefer replacing a matching route of the same
"ECMP-able-ness" as the replace argument. If there is no such candidate,
fallback to the first route found.
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
