The driver have a race, experienced only with PREEMPT_RT patchset:
CPU0 | CPU1
==================================================================
qcom_geni_serial_probe |
uart_add_one_port |
| serdev_drv_probe
| qca_serdev_probe
| serdev_device_open
| uart_open
| uart_startup
| qcom_geni_serial_startup
| enable_irq
| __irq_startup
| WARN_ON()
| IRQ not activated
request_threaded_irq |
irq_domain_activate_irq |
The warning:
894000.serial: ttyHS1 at MMIO 0x894000 (irq = 144, base_baud = 0) is a MSM
serial serial0: tty port ttyHS1 registered
WARNING: CPU: 7 PID: 107 at kernel/irq/chip.c:241 __irq_startup+0x78/0xd8
...
qcom_geni_serial 894000.serial: serial engine reports 0 RX bytes in!
Adding UART port triggers probe of child serial devices - serdev and
eventually Qualcomm Bluetooth hci_qca driver. This opens UART port
which enables the interrupt before it got activated in
request_threaded_irq(). The issue originates in commit f3974413cf
("tty: serial: qcom_geni_serial: Wakeup IRQ cleanup") and discussion on
mailing list [1]. However the above commit does not explain why the
uart_add_one_port() is moved above requesting interrupt.
[1] https://lore.kernel.org/all/5d9f3dfa.1c69fb81.84c4b.30bf@mx.google.com/
Fixes: f3974413cf ("tty: serial: qcom_geni_serial: Wakeup IRQ cleanup")
Cc: <stable@vger.kernel.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20230505152301.2181270-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reports:
drivers/tty/serial/arc_uart.c:631 arc_serial_probe() warn:
'port->membase' from of_iomap() not released on lines: 631.
In arc_serial_probe(), if uart_add_one_port() fails,
port->membase is not released, which would cause a resource leak.
To fix this, I replace of_iomap with devm_platform_ioremap_resource.
Fixes: 8dbe1d5e09 ("serial/arc: inline the probe helper")
Signed-off-by: Ke Zhang <m202171830@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230428031636.44642-1-m202171830@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Possibly the last PCI controller-based (i.e. not a soft/winmodem)
dial-up modem one can still buy.
Looks to have a stock XR17C154 PCI UART chip for communication, but for
some reason when provisioning the PCI IDs they swapped the vendor and
subvendor IDs. Otherwise this card would have worked out of the box.
Searching online, some folks seem to not have this issue and others do,
so it is possible only some batches of cards have this error.
Create a new macro to handle the switched IDs and add support here.
Signed-off-by: Andrew Davis <afd@ti.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230420160209.28221-1-afd@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull char/misc drivers updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost
breaks even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (196 commits)
mcb-lpc: Reallocate memory region to avoid memory overlapping
mcb-pci: Reallocate memory region to avoid memory overlapping
mcb: Return actual parsed size when reading chameleon table
kernel/configs: Drop Android config fragments
virt: acrn: Replace obsolete memalign() with posix_memalign()
spmi: Add a check for remove callback when removing a SPMI driver
spmi: fix W=1 kernel-doc warnings
spmi: mtk-pmif: Drop of_match_ptr for ID table
spmi: pmic-arb: Convert to platform remove callback returning void
spmi: mtk-pmif: Convert to platform remove callback returning void
spmi: hisi-spmi-controller: Convert to platform remove callback returning void
w1: gpio: remove unnecessary ENOMEM messages
w1: omap-hdq: remove unnecessary ENOMEM messages
w1: omap-hdq: add SPDX tag
w1: omap-hdq: allow compile testing
w1: matrox: remove unnecessary ENOMEM messages
w1: matrox: use inline over __inline__
w1: matrox: switch from asm to linux header
w1: ds2482: do not use assignment in if condition
w1: ds2482: drop unnecessary header
...
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
Pull tty / serial updates from Greg KH:
"Here is the big set of tty/serial driver updates for 6.4-rc1.
Nothing major, just lots of tiny, constant, forward development. This
includes:
- obligatory n_gsm updates and feature additions
- 8250_em driver updates
- sh-sci driver updates
- dts cleanups and updates
- general cleanups and improvements by Ilpo and Jiri
- other small serial driver core fixes and driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (87 commits)
n_gsm: Use array_index_nospec() with index that comes from userspace
tty: vt: drop checks for undefined VT_SINGLE_DRIVER
tty: vt: distribute EXPORT_SYMBOL()
tty: vt: simplify some cases in tioclinux()
tty: vt: reformat tioclinux()
tty: serial: sh-sci: Fix end of transmission on SCI
tty: serial: sh-sci: Add support for tx end interrupt handling
tty: serial: sh-sci: Fix TE setting on SCI IP
tty: serial: sh-sci: Add RZ/G2L SCIFA DMA rx support
tty: serial: sh-sci: Add RZ/G2L SCIFA DMA tx support
serial: max310x: fix IO data corruption in batched operations
serial: core: Disable uart_start() on uart_remove_one_port()
serial: 8250: Reinit port->pm on port specific driver unbind
serial: 8250: Add missing wakeup event reporting
tty: serial: fsl_lpuart: use UARTMODIR register bits for lpuart32 platform
tty: serial: fsl_lpuart: adjust buffer length to the intended size
serial: fix TIOCSRS485 locking
serial: make SiFive serial drivers depend on ARCH_ symbols
tty: synclink_gt: don't allocate and pass dummy flags
tty: serial: simplify qcom_geni_serial_send_chunk_fifo()
...
Pull networking updates from Paolo Abeni:
"Core:
- Introduce a config option to tweak MAX_SKB_FRAGS. Increasing the
default value allows for better BIG TCP performances
- Reduce compound page head access for zero-copy data transfers
- RPS/RFS improvements, avoiding unneeded NET_RX_SOFTIRQ when
possible
- Threaded NAPI improvements, adding defer skb free support and
unneeded softirq avoidance
- Address dst_entry reference count scalability issues, via false
sharing avoidance and optimize refcount tracking
- Add lockless accesses annotation to sk_err[_soft]
- Optimize again the skb struct layout
- Extends the skb drop reasons to make it usable by multiple
subsystems
- Better const qualifier awareness for socket casts
BPF:
- Add skb and XDP typed dynptrs which allow BPF programs for more
ergonomic and less brittle iteration through data and
variable-sized accesses
- Add a new BPF netfilter program type and minimal support to hook
BPF programs to netfilter hooks such as prerouting or forward
- Add more precise memory usage reporting for all BPF map types
- Adds support for using {FOU,GUE} encap with an ipip device
operating in collect_md mode and add a set of BPF kfuncs for
controlling encap params
- Allow BPF programs to detect at load time whether a particular
kfunc exists or not, and also add support for this in light
skeleton
- Bigger batch of BPF verifier improvements to prepare for upcoming
BPF open-coded iterators allowing for less restrictive looping
capabilities
- Rework RCU enforcement in the verifier, add kptr_rcu and enforce
BPF programs to NULL-check before passing such pointers into kfunc
- Add support for kptrs in percpu hashmaps, percpu LRU hashmaps and
in local storage maps
- Enable RCU semantics for task BPF kptrs and allow referenced kptr
tasks to be stored in BPF maps
- Add support for refcounted local kptrs to the verifier for allowing
shared ownership, useful for adding a node to both the BPF list and
rbtree
- Add BPF verifier support for ST instructions in
convert_ctx_access() which will help new -mcpu=v4 clang flag to
start emitting them
- Add ARM32 USDT support to libbpf
- Improve bpftool's visual program dump which produces the control
flow graph in a DOT format by adding C source inline annotations
Protocols:
- IPv4: Allow adding to IPv4 address a 'protocol' tag. Such value
indicates the provenance of the IP address
- IPv6: optimize route lookup, dropping unneeded R/W lock acquisition
- Add the handshake upcall mechanism, allowing the user-space to
implement generic TLS handshake on kernel's behalf
- Bridge: support per-{Port, VLAN} neighbor suppression, increasing
resilience to nodes failures
- SCTP: add support for Fair Capacity and Weighted Fair Queueing
schedulers
- MPTCP: delay first subflow allocation up to its first usage. This
will allow for later better LSM interaction
- xfrm: Remove inner/outer modes from input/output path. These are
not needed anymore
- WiFi:
- reduced neighbor report (RNR) handling for AP mode
- HW timestamping support
- support for randomized auth/deauth TA for PASN privacy
- per-link debugfs for multi-link
- TC offload support for mac80211 drivers
- mac80211 mesh fast-xmit and fast-rx support
- enable Wi-Fi 7 (EHT) mesh support
Netfilter:
- Add nf_tables 'brouting' support, to force a packet to be routed
instead of being bridged
- Update bridge netfilter and ovs conntrack helpers to handle IPv6
Jumbo packets properly, i.e. fetch the packet length from
hop-by-hop extension header. This is needed for BIT TCP support
- The iptables 32bit compat interface isn't compiled in by default
anymore
- Move ip(6)tables builtin icmp matches to the udptcp one. This has
the advantage that icmp/icmpv6 match doesn't load the
iptables/ip6tables modules anymore when iptables-nft is used
- Extended netlink error report for netdevice in flowtables and
netdev/chains. Allow for incrementally add/delete devices to netdev
basechain. Allow to create netdev chain without device
Driver API:
- Remove redundant Device Control Error Reporting Enable, as PCI core
has already error reporting enabled at enumeration time
- Move Multicast DB netlink handlers to core, allowing devices other
then bridge to use them
- Allow the page_pool to directly recycle the pages from safely
localized NAPI
- Implement lockless TX queue stop/wake combo macros, allowing for
further code de-duplication and sanitization
- Add YNL support for user headers and struct attrs
- Add partial YNL specification for devlink
- Add partial YNL specification for ethtool
- Add tc-mqprio and tc-taprio support for preemptible traffic classes
- Add tx push buf len param to ethtool, specifies the maximum number
of bytes of a transmitted packet a driver can push directly to the
underlying device
- Add basic LED support for switch/phy
- Add NAPI documentation, stop relaying on external links
- Convert dsa_master_ioctl() to netdev notifier. This is a
preparatory work to make the hardware timestamping layer selectable
by user space
- Add transceiver support and improve the error messages for CAN-FD
controllers
New hardware / drivers:
- Ethernet:
- AMD/Pensando core device support
- MediaTek MT7981 SoC
- MediaTek MT7988 SoC
- Broadcom BCM53134 embedded switch
- Texas Instruments CPSW9G ethernet switch
- Qualcomm EMAC3 DWMAC ethernet
- StarFive JH7110 SoC
- NXP CBTX ethernet PHY
- WiFi:
- Apple M1 Pro/Max devices
- RealTek rtl8710bu/rtl8188gu
- RealTek rtl8822bs, rtl8822cs and rtl8821cs SDIO chipset
- Bluetooth:
- Realtek RTL8821CS, RTL8851B, RTL8852BS
- Mediatek MT7663, MT7922
- NXP w8997
- Actions Semi ATS2851
- QTI WCN6855
- Marvell 88W8997
- Can:
- STMicroelectronics bxcan stm32f429
Drivers:
- Ethernet NICs:
- Intel (1G, icg):
- add tracking and reporting of QBV config errors
- add support for configuring max SDU for each Tx queue
- Intel (100G, ice):
- refactor mailbox overflow detection to support Scalable IOV
- GNSS interface optimization
- Intel (i40e):
- support XDP multi-buffer
- nVidia/Mellanox:
- add the support for linux bridge multicast offload
- enable TC offload for egress and engress MACVLAN over bond
- add support for VxLAN GBP encap/decap flows offload
- extend packet offload to fully support libreswan
- support tunnel mode in mlx5 IPsec packet offload
- extend XDP multi-buffer support
- support MACsec VLAN offload
- add support for dynamic msix vectors allocation
- drop RX page_cache and fully use page_pool
- implement thermal zone to report NIC temperature
- Netronome/Corigine:
- add support for multi-zone conntrack offload
- Solarflare/Xilinx:
- support offloading TC VLAN push/pop actions to the MAE
- support TC decap rules
- support unicast PTP
- Other NICs:
- Broadcom (bnxt): enforce software based freq adjustments only on
shared PHC NIC
- RealTek (r8169): refactor to addess ASPM issues during NAPI poll
- Micrel (lan8841): add support for PTP_PF_PEROUT
- Cadence (macb): enable PTP unicast
- Engleder (tsnep): add XDP socket zero-copy support
- virtio-net: implement exact header length guest feature
- veth: add page_pool support for page recycling
- vxlan: add MDB data path support
- gve: add XDP support for GQI-QPL format
- geneve: accept every ethertype
- macvlan: allow some packets to bypass broadcast queue
- mana: add support for jumbo frame
- Ethernet high-speed switches:
- Microchip (sparx5): Add support for TC flower templates
- Ethernet embedded switches:
- Broadcom (b54):
- configure 6318 and 63268 RGMII ports
- Marvell (mv88e6xxx):
- faster C45 bus scan
- Microchip:
- lan966x:
- add support for IS1 VCAP
- better TX/RX from/to CPU performances
- ksz9477: add ETS Qdisc support
- ksz8: enhance static MAC table operations and error handling
- sama7g5: add PTP capability
- NXP (ocelot):
- add support for external ports
- add support for preemptible traffic classes
- Texas Instruments:
- add CPSWxG SGMII support for J7200 and J721E
- Intel WiFi (iwlwifi):
- preparation for Wi-Fi 7 EHT and multi-link support
- EHT (Wi-Fi 7) sniffer support
- hardware timestamping support for some devices/firwmares
- TX beacon protection on newer hardware
- Qualcomm 802.11ax WiFi (ath11k):
- MU-MIMO parameters support
- ack signal support for management packets
- RealTek WiFi (rtw88):
- SDIO bus support
- better support for some SDIO devices (e.g. MAC address from
efuse)
- RealTek WiFi (rtw89):
- HW scan support for 8852b
- better support for 6 GHz scanning
- support for various newer firmware APIs
- framework firmware backwards compatibility
- MediaTek WiFi (mt76):
- P2P support
- mesh A-MSDU support
- EHT (Wi-Fi 7) support
- coredump support"
* tag 'net-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2078 commits)
net: phy: hide the PHYLIB_LEDS knob
net: phy: marvell-88x2222: remove unnecessary (void*) conversions
tcp/udp: Fix memleaks of sk and zerocopy skbs with TX timestamp.
net: amd: Fix link leak when verifying config failed
net: phy: marvell: Fix inconsistent indenting in led_blink_set
lan966x: Don't use xdp_frame when action is XDP_TX
tsnep: Add XDP socket zero-copy TX support
tsnep: Add XDP socket zero-copy RX support
tsnep: Move skb receive action to separate function
tsnep: Add functions for queue enable/disable
tsnep: Rework TX/RX queue initialization
tsnep: Replace modulo operation with mask
net: phy: dp83867: Add led_brightness_set support
net: phy: Fix reading LED reg property
drivers: nfc: nfcsim: remove return value check of `dev_dir`
net: phy: dp83867: Remove unnecessary (void*) conversions
net: ethtool: coalesce: try to make user settings stick twice
net: mana: Check if netdev/napi_alloc_frag returns single page
net: mana: Rename mana_refill_rxoob and remove some empty lines
net: veth: add page_pool stats
...
Merge ACPI bus type driver changes, ACPI backlight driver updates and a
series of cleanups related to of.h for 6.4-rc1:
- Ensure that ACPI notify handlers are not running after removal and
clean up code in acpi_sb_notify() (Rafael Wysocki).
- Remove register_backlight_delay module option and code and remove
quirks for false-positive backlight control support advertised on
desktop boards (Hans de Goede).
- Replace irqdomain.h include with struct declarations in ACPI headers
and update several pieces of code previously including of.h
implicitly through those headers (Rob Herring).
* acpi-bus:
ACPI: bus: Ensure that notify handlers are not running after removal
ACPI: bus: Add missing braces to acpi_sb_notify()
* acpi-video:
ACPI: video: Remove desktops without backlight DMI quirks
ACPI: video: Remove register_backlight_delay module option and code
* acpi-misc:
ACPI: Replace irqdomain.h include with struct declarations
fpga: lattice-sysconfig-spi: Add explicit include for of.h
tpm: atmel: Add explicit include for of.h
virtio-mmio: Add explicit include for of.h
pata: ixp4xx: Add explicit include for of.h
ata: pata_macio: Add explicit include of irqdomain.h
serial: 8250_tegra: Add explicit include for of.h
net: rfkill-gpio: Add explicit include for of.h
staging: iio: resolver: ad2s1210: Add explicit include for of.h
iio: adc: ad7292: Add explicit include for of.h
Adds serdev_device_break_ctl() and an implementation for ttyport.
This function simply calls the break_ctl in tty layer, which can
assert a break signal over UART-TX line, if the tty and the
underlying platform and UART peripheral supports this operation.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This replaces all instances of ENOTSUPP with EOPNOTSUPP since ENOTSUPP
is not a standard error code. This will help maintain consistency in
error codes when new serdev API's are added.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
As per the RZ/G2L users hardware manual (Rev.1.20 Sep, 2022), section
23.3.7 Serial Data Transmission (Asynchronous Mode), it is mentioned
that, set the SCR.TIE bit to 0 and SCR.TEIE bit to 1, after the last
data to be transmitted are written to the TDR.
This will generate tx end interrupt and in the handler set SCR.TE and
SCR.TEIE to 0.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-5-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the RZ/G2L users hardware manual (Rev.1.20 Sep, 2022), section
23.3.7 Serial Data Transmission (Asynchronous Mode) it is mentioned
that the TE (transmit enable) must be set after setting TIE (transmit
interrupt enable) or these 2 bits are set to 1 simultaneously by a
single instruction. So set these 2 bits in single instruction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-4-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA IP on RZ/G2L SoC has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked. Similarly clearing DMARS register makes signal to work as
interrupt signal and subsequent interrupt requests to the interrupt
controller are unmasked.
Add SCIFA DMA rx support for RZ/G2L alike SoCs by disabling RXI line
interrupt and setting DMARS registers by DMA api for DMA transfer request.
Apart from this, we must set FIFO trigger to 1 for the expected behavior
of the receive transmission.
While at it replace the parameter irq to s->irqs[SCIx_RXI_IRQ] in
disable_irq_nosync() to match enable_irq() in sci_dma_rx_reenable_irq().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA IP on RZ/G2L SoC has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked. Similarly clearing DMARS register makes signal to work as
interrupt signal and subsequent interrupt requests to the interrupt
controller are unmasked.
Add SCIFA DMA tx support for RZ/G2L alike SoCs by disabling TXI line
interrupt and setting DMARS registers by DMA api for DMA transfer request.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
