Newer firmware versions for the Pantech UML290 use a different
subclass ID. The Windows driver match on both IDs, so we do
that as well.
The ZTE (Vodafone) K5006-Z is a new device.
Cc: Dan Williams <dcbw@redhat.com>
Cc: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the matching macros to make the device id
list easier to read and maintain.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 6 new devices and one modified device, based on
information from laptop vendor Windows drivers.
Sony provides a driver with two new devices using
a Gobi 2k+ layout (1199:68a5 and 1199:68a9). The
Sony driver also adds a non-standard QMI/net
interface to the already supported 1199:9011
Gobi device. We do not know whether this is an
alternate interface number or an additional
interface which might be present, but that doesn't
really matter.
Lenovo provides a driver supporting 4 new devices:
- MC7770 (1199:901b) with standard Gobi 2k+ layout
- MC7700 (0f3d:68a2) with layout similar to MC7710
- MC7750 (114f:68a2) with layout similar to MC7710
- EM7700 (1199:901c) with layout similar to MC7710
Note regaring the three devices similar to MC7710:
The Windows drivers only support interface #8 on these
devices. The MC7710 can support QMI/net functions on
interface #19 and #20 as well, and this driver is
verified to work on interface #19 (a firmware bug is
suspected to prevent #20 from working).
We do not enable these additional interfaces until they
either show up in a Windows driver or are verified to
work in some other way. Therefore limiting the new
devices to interface #8 for now.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver support many composite USB devices where the
interface class/subclass/protocol provides no information
about the interface function. Interfaces with different
functions may all use ff/ff/ff, like this example of
a device with three serial interfaces and three QMI/wwan
interfaces:
T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1199 ProdID=68a2 Rev= 0.06
S: Manufacturer=Sierra Wireless, Incorporated
S: Product=MC7710
S: SerialNumber=3581780xxxxxx
C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Instead of class/subclass/protocol the vendor use fixed
interface numbers for each function, and the Windows
drivers use these numbers to match driver and function.
The driver has had its own interface number whitelisting
code to simulate this functionality. Replace this with
generic interface number matching now that the USB subsystem
support is there. This
- removes the need for a driver_info structure per
interface number,
- avoids running the probe function for unsupported
interfaces, and
- simplifies the code.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allocate memory for 'req' with usb_alloc_urb() and then test
'if (!req || rx_submit(pnd, req, GFP_KERNEL | __GFP_COLD))'.
If we enter that branch due to '!req' then there is no problem. But if
we enter the branch due to 'req' being != 0 and the 'rx_submit()' call
being false, then we'll leak the memory we allocated.
Deal with the leak by always calling 'usb_free_urb(req)' when entering
the branch. If 'req' happens to be 0 then the call is harmless, if it
is not 0 then we free the memory we allocated but don't need.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Rémi Denis-Courmont <remi@remlab.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb->pfmemalloc flag gets set to true iff during the slab allocation
of data in __alloc_skb that the the PFMEMALLOC reserves were used. If
page splitting is used, it is possible that pages will be allocated from
the PFMEMALLOC reserve without propagating this information to the skb.
This patch propagates page->pfmemalloc from pages allocated for fragments
to the skb.
It works by reintroducing and expanding the skb_alloc_page() API to take
an skb. If the page was allocated from pfmemalloc reserves, it is
automatically copied. If the driver allocates the page before the skb, it
should call skb_propagate_pfmemalloc() after the skb is allocated to
ensure the flag is copied properly.
Failure to do so is not critical. The resulting driver may perform slower
if it is used for swap-over-NBD or swap-over-NFS but it should not result
in failure.
[davem@davemloft.net: API rename and consistency]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The problem is that we call this with a spin lock held. The call tree
is:
kaweth_start_xmit() holds kaweth->device_lock.
-> kaweth_async_set_rx_mode()
-> kaweth_control()
-> kaweth_internal_control_msg()
The kaweth_internal_control_msg() function is only called from
kaweth_control() which used GFP_ATOMIC for its allocations.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates and fixes from David Miller:
1) Reinstate the no-ref optimization for input route lookups in ipv4 to
fix some routing cache removal perf regressions.
2) Make TCP socket pre-demux work on ipv6 side too, from Eric Dumazet.
3) Get RX hash value from correct place in be2net driver, from
Sarveshwar Bandi.
4) Validation of FIB cached routes missing critical check, from Eric
Dumazet.
5) EEH support in mlx4 driver, from Kleber Sacilotto de Souza.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (23 commits)
ipv6: Early TCP socket demux
ipv4: Fix input route performance regression.
pch_gbe: vlan skb len fix
pch_gbe: add extra clean tx
pch_gbe: fix transmit watchdog timeout
ixgbe: fix panic while dumping packets on Tx hang with IOMMU
be2net: Fix to parse RSS hash from Receive completions correctly.
net/mlx4_en: Limit the RFS filter IDs to be < RPS_NO_FILTER
hyperv: Add error handling to rndis_filter_device_add()
hyperv: Add a check for ring_size value
ipv4: rt_cache_valid must check expired routes
net/pch_gpe: Cannot disable ethernet autonegation
qeth: repair crash in qeth_l3_vlan_rx_kill_vid()
netiucv: cleanup attribute usage
net: wiznet add missing HAS_IOMEM dependency
be2net: Missing byteswap in be_get_fw_log_level causes oops on PowerPC
mlx4: Add support for EEH error recovery
cdc-ncm: tag Ericsson WWAN devices (eg F5521gw) with FLAG_WWAN
wanmain: comparing array with NULL
caif: fix NULL pointer check
...
Tag Ericsson NCM devices as WWAN modems, since they almost certainly all
are. This way userspace clients know that the device requires further
setup on the AT-capable serial ports before connectivity is available.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Pull trivial tree from Jiri Kosina:
"Trivial updates all over the place as usual."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
Fix typo in include/linux/clk.h .
pci: hotplug: Fix typo in pci
iommu: Fix typo in iommu
video: Fix typo in drivers/video
Documentation: Add newline at end-of-file to files lacking one
arm,unicore32: Remove obsolete "select MISC_DEVICES"
module.c: spelling s/postition/position/g
cpufreq: Fix typo in cpufreq driver
trivial: typo in comment in mksysmap
mach-omap2: Fix typo in debug message and comment
scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
Change email address for Steve Glendinning
Btrfs: fix typo in convert_extent_bit
via: Remove bogus if check
netprio_cgroup.c: fix comment typo
backlight: fix memory leak on obscure error path
Documentation: asus-laptop.txt references an obsolete Kconfig item
Documentation: ManagementStyle: fixed typo
mm/vmscan: cleanup comment error in balance_pgdat
mm: cleanup on the comments of zone_reclaim_stat
...
This patch adds the asix_set_eeprom() function to provide support for
programming the configuration EEPROM via ethtool.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code for reading the EEPROM via ethtool in the asix
driver has a few issues. It cannot handle odd length values
(accesses must be aligned at 16 bit boundaries) and interprets the
offset provided by ethtool as 16 bit word offset instead as byte offset.
The new code for asix_get_eeprom() introduced by this patch is
modeled after the code in
drivers/net/ethernet/atheros/atl1e/atl1e_ethtool.c
and provides read access to the entire EEPROM with arbitrary
offsets and lengths.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return -ENOTSUPP if the initialization fails because the
device is configured for a mode that is not supported by the driver.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usbnet API use the device ID table to store a pointer to
a minidriver. Setting a generic pointer for dynamic device
IDs will in most cases make them work as expected. usbnet
will otherwise treat the dynamic IDs as blacklisted. That is
rarely useful.
There is no standard class describing devices supported by
this driver, and most vendors don't even provide enough
information to allow vendor specific wildcard matching. The
result is that most of the supported devices must be
explicitly listed in the device table. Allowing dynamic IDs
to work both simplifies testing and verification of new
devices, and provides a way for end users to use a device
before the ID is added to the driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
I no longer have a mailbox at smsc.com, and I've had two reports
that that email address now bounces from people trying to
contact me. This patch updates all references to that invalid
address to one that I can be contacted on more permanently.
This patch also updates the maintainer status to reflect
the fact I'm no longer directly paid to maintain these drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Asix AX88172A is a USB 2.0 Ethernet interface that supports both an
internal PHY as well as an external PHY (connected via MII).
This patch adds a driver for the AX88172A and provides support for
both modes and the phylib.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the new driver for the AX88172A to share code with the
existing drivers for ASIX devices.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch further creates two additional copies of asix.c.
In another patch these copies will be used to factor out
common code.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"retval" has to be a signed integer for the error handling to work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
