pasemi_defconfig hasn't been updated for a year.
Mostly a refresh of defaults, but this also disables 64K pages.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes USB GPIOs numbers for MPC8569E-MDS boards, plus
according to the latest HW Getting Started Guide (rev 3.3, pilot
boards), USB "POWER" GPIO polarity has changed, it is no longer
inverted.
This patch makes USB Host somewhat work on pilot boards, though
there are still some problems with determining devices speed and
long bulk transfers.
Reported-by: Liu Yu <Yu.Liu@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI-e addressing was originally patterned of the MPC8548CDS
which has PCI1, PCI2, and PCI-e. Since this board only has
PCI1 and PCI-e, it makes more sense to be similar to the MPC8568MDS
board. This does that by cutting the PCI/PCI-e I/O sizes from
16MB to 8MB and pulling the PCI-e I/O range back to 0xe280_0000
(the hole where PCI2 I/O would have been).
This also fixes a typo where an extra zero made an 8MB range a 128MB
range, removes the hole left by PCI2 from the aliases, and sets the
clocks to match the oscillators that are actually on the board.
With accompanying u-boot updates, PCI-e has been validated with
both a sky2 card (1148:9e00) and an e1000 card (8086:108b).
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Patch f598282f51 exposed a problem in
powerpc MSI-X functionality, making network interfaces such as ixgbe
and cxgb3 stop to work when MSI-X is enabled. RX interrupts were not
being generated.
The problem was caused because MSI irq was not being effectively
unmasked after device initialization.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Doing so causes xtime to be negative which crashes the timekeeping
code in funny ways when doing suspend/resume
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I inadvertently left that debug code enabled, causing the number of
contexts to be clamped to 31 which is going to slow things down on
4xx and just plain breaks 8xx
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add some dummy symbols for the branches at 0xf00, 0xf20 and 0xf40,
otherwise hits end up in trap_0e which is confusing to the user.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If CONFIG_PPC_ISERIES isn't defined we end up with
iseries_check_pending_irqs and do_work at the same address.
perf ends up picking iseries_check_pending_irqs which creates
confusing backtraces. Hide it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A lot of hits in "setup" doesn't make much sense, so hide this symbol and
allow all the hits to end up in copy_4k_page.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Kernel modules should be able to place their debug output inside our
powerpc debugfs directory.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The overhead of HCALL_STATS is quite high and the functionality is very
rarely used. Key statistics are also missing (eg min/max).
With the new hcall tracepoints much more powerful tracing can be done in
a kernel module. Lets disable this by default.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
While most users of the hcall tracepoints will only want the opcode
and return code, some will want all the arguments. To avoid the
complexity of using varargs we pass a pointer to the register save
area, which contains all the arguments.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add hcall_entry and hcall_exit tracepoints. This replaces the inline
assembly HCALL_STATS code and converts it to use the new tracepoints.
To keep the disabled case as quick as possible, we embed a status word
in the TOC so we can get at it with a single load. By doing so we
keep the overhead at a minimum. Time taken for a null hcall:
No tracepoint code: 135.79 cycles
Disabled tracepoints: 137.95 cycles
For reference, before this patch enabling HCALL_STATS resulted in a null
hcall of 201.44 cycles!
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We can monitor the effectiveness of our power management of both the
kernel and hypervisor by probing the timer interrupt. For example, on
this box we see 10.37s timer interrupts on an idle core:
<idle>-0 [010] 3900.671297: timer_interrupt_entry: pt_regs=c0000000ce1e7b10
<idle>-0 [010] 3900.671302: timer_interrupt_exit: pt_regs=c0000000ce1e7b10
<idle>-0 [010] 3911.042963: timer_interrupt_entry: pt_regs=c0000000ce1e7b10
<idle>-0 [010] 3911.042968: timer_interrupt_exit: pt_regs=c0000000ce1e7b10
<idle>-0 [010] 3921.414630: timer_interrupt_entry: pt_regs=c0000000ce1e7b10
<idle>-0 [010] 3921.414635: timer_interrupt_exit: pt_regs=c0000000ce1e7b10
Since we have a 207MHz decrementer it will go negative and fire every 10.37s
even if Linux is completely idle.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds powerpc-specific tracepoints for interrupt entry and exit.
While we already have generic irq_handler_entry and irq_handler_exit
tracepoints there are cases on our virtualised powerpc machines where an
interrupt is presented to the OS, but subsequently handled by the hypervisor.
This means no OS interrupt handler is invoked.
Here is an example on a POWER6 machine with the patch below applied:
<idle>-0 [006] 3243.949840744: irq_entry: pt_regs=c0000000ce31fb10
<idle>-0 [006] 3243.949850520: irq_exit: pt_regs=c0000000ce31fb10
<idle>-0 [007] 3243.950218208: irq_entry: pt_regs=c0000000ce323b10
<idle>-0 [007] 3243.950224080: irq_exit: pt_regs=c0000000ce323b10
<idle>-0 [000] 3244.021879320: irq_entry: pt_regs=c000000000a63aa0
<idle>-0 [000] 3244.021883616: irq_handler_entry: irq=87 handler=eth0
<idle>-0 [000] 3244.021887328: irq_handler_exit: irq=87 return=handled
<idle>-0 [000] 3244.021897408: irq_exit: pt_regs=c000000000a63aa0
Here we see two phantom interrupts (no handler was invoked), followed
by a real interrupt for eth0. Without the tracepoints in this patch we
would have missed the phantom interrupts.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Hook up the alignment-faults and emulation-faults events for powerpc.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
perf_event wants a separate event for alignment and emulation faults,
so create another emulation event. This will make it easy to hook in
perf_event at one spot.
We pass in regs which will be required for these events.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In continuous sampling mode we want the SDAR to update. While we can
select between dcache misses and ERAT (L1-TLB) misses, a decent default
is to enable both.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
