* git://git.infradead.org/battery-2.6:
power_supply: Sharp SL-6000 (tosa) batteries support
power_supply: fix up CHARGE_COUNTER output to be more precise
power_supply: add CHARGE_COUNTER property and olpc_battery support for it
power_supply: bump EC version check that we refuse to run with in olpc_battery
power_supply: cleanup of the OLPC battery driver
power_supply: add eeprom dump file to olpc_battery's sysfs
power_supply: Support serial number in olpc_battery
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (28 commits)
mm/hugetlb.c must #include <asm/io.h>
video: Fix up hp6xx driver build regressions.
sh: defconfig updates.
sh: Kill off stray mach-rsk7203 reference.
serial: sh-sci: Fix up SH7760/SH7780/SH7785 early printk regression.
sh: Move out individual boards without mach groups.
sh: Make sure AT_SYSINFO_EHDR is exposed to userspace in asm/auxvec.h.
sh: Allow SH-3 and SH-5 to use common headers.
sh: Provide common CPU headers, prune the SH-2 and SH-2A directories.
sh/maple: clean maple bus code
sh: More header path fixups for mach dir refactoring.
sh: Move out the solution engine headers to arch/sh/include/mach-se/
sh: I2C fix for AP325RXA and Migo-R
sh: Shuffle the board directories in to mach groups.
sh: dma-sh: Fix up dreamcast dma.h mach path.
sh: Switch KBUILD_DEFCONFIG to shx3_defconfig.
sh: Add ARCH_DEFCONFIG entries for sh and sh64.
sh: Fix compile error of Solution Engine
sh: Proper __put_user_asm() size mismatch fix.
sh: Stub in a dummy ENTRY_OFFSET for uImage offset calculation.
...
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] qeth: avoid use of include/asm-s390
[S390] dont use kthread for smp_rescan_cpus().
[S390] virtio console: fix section mismatch warning.
[S390] cio: Include linux/string.h in schid.h.
[S390] qdio: fix section mismatch bug.
[S390] stp: fix section mismatch warning.
[S390] Remove diag 0x260 call from memory detection.
[S390] qdio: make sure qdr is aligned to page size
[S390] Add support for memory hot-remove.
[S390] Wire up new syscalls.
[S390] cio: Memory allocation for idset changed.
[S390] qeth: preallocated qeth header for hiper socket
[S390] Optimize storage key operations for anon pages
[S390] nohz/sclp: disable timer on synchronous waits.
[S390] ipl: Reboot from alternate device does not work when booting from file
[S390] dasd: Add support for enhanced VM UID
[S390] Remove last P390 trace.
For anonymous pages without a swap cache backing the check in
page_remove_rmap for the physical dirty bit in page_remove_rmap is
unnecessary. The instructions that are used to check and reset the dirty
bit are expensive. Removing the check noticably speeds up process exit.
In addition the clearing of the dirty bit in __SetPageUptodate is
pointless as well. With these two changes there is no storage key
operation for an anonymous page anymore if it does not hit the swap
space.
The micro benchmark which repeatedly executes an empty shell script
gets about 5% faster.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
sclp_sync_wait wait synchronously for an sclp interrupt and disables
timer interrupts. However on the irq enter paths there is an extra
check if a timer interrupt would be due and calls the timer callback.
This would schedule softirqs in the wrong context.
So introduce local_tick_enable/disable which prevents this.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
During startup we check if diag308 works using diag 308 subcode 6,
which stores the actual ipl information. This fails with rc = 0x102, if
the system has been ipled from the HMC using load from CD or load from file.
In the case of rc = 0x102 we have to assume that diag 308 is working,
since it still can be used to ipl from an alternative device.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The new kgdb architecture specific handler registers and unregisters
dynamically for exceptions depending on when you configure a kgdb I/O
driver.
Aside from initializing the exceptions earlier in the boot process,
kgdb should have no impact on a device when it is compiled in so long
as an I/O module is not configured for use.
There have been quite a number of contributors during the existence of
this patch (see arch/mips/kernel/kgdb.c). Most recently Jason
re-wrote the mips kgdb logic to use the die notification handlers.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch explicitly removes the kgdb implementation, for mips which
is intended to be followed by a patch that adds a kgdb implementation
for MIPS that makes use of the kgdb core in the kernel.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Unify calling of early_serial_txx9_setup.
* Use dedicated serial clock on RBTX4938.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Random cleanups spotted by checkpatch script.
* Do not initialize panic_timeout. "panic=" kernel parameter can be used.
* Do not add "ip=any" or "ip=bootp". This options is not board specific.
* Do not add "root=/dev/nfs". This is default on CONFIG_ROOT_NFS.
* Kill unused error checking.
* Fix IRQ comment to match current code.
* Kill some unneeded includes
* ST0_ERL is already cleared in generic code.
* conswitchp is initialized generic code.
* __init is not needed in prototype.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make some TX4938 SoC specific code independent from board specific code.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make some TX3927 SoC specific code independent from board specific code.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Lockless get_user_pages_fast() for 64-bit (v3)
powerpc: Don't use the wrong thread_struct for ptrace get/set VSX regs
powerpc: Fix ptrace buffer size for VSX
powerpc: Correctly hookup PTRACE_GET/SETVSRREGS for 32 bit processes
ide/powermac: Fix use of uninitialized pointer on media-bay
powerpc: Allow non-hcall return values for lparcfg writes
ipmi/powerpc: Use linux/of_{device,platform}.h instead of asm
powerpc/fsl: proliferate simple-bus compatibility to soc nodes
Documentation: remove old sbc8260 board specific information
cpm2: Rework baud rate generators configuration to support external clocks.
powerpc: rtc_cmos_setup: assign interrupts only if there is i8259 PIC
cpm_uart: Add generic clock API support to set baudrates
cpm_uart: Modem control lines support
powerpc: implement GPIO LIB API on CPM1 Freescale SoC.
cpm2: Implement GPIO LIB API on CPM2 Freescale SoC.
powerpc: Fix 8xx build failure
powerpc: clean up the Book-E HW watchpoint support
