Pull ktest fixes from Steven Rostedt:
"Greg Kroah-Hartman reported to me that the ktest of v4.11-rc1 locked
up in an infinite loop while doing the make mrproper.
Looking into the cause I noticed that a recent update to the function
run_command (used for running all shell commands, including "make
mrproper") changed the internal loop to use the function
wait_for_input.
The wait_for_input function uses select to look at two file
descriptors. One is the file descriptor of the command it is running,
the other is STDIN. The STDIN check was not checking the return status
of the sysread call, and was also just writing a lot of data into
syswrite without regard to the size of the data read.
Changing the code to check the return status of sysread, and also to
still process the passed in descriptor data without looping back to
the select fixed Greg's problem.
While looking at this code I also realized that the loop did not honor
the timeout if STDIN always had input (or for some reason return
error). this could prevent wait_for_input to timeout on the file
descriptor it is suppose to be waiting for. That is fixed too"
* tag 'ktest-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Make sure wait_for_input does honor the timeout
ktest: Fix while loop in wait_for_input
The function wait_for_input takes in a timeout, and even has a default
timeout. But if for some reason the STDIN descriptor keeps sending in data,
the function will never time out. The timout is to wait for the data from
the passed in file descriptor, not for STDIN. Adding a test in the case
where there's no data from the passed in file descriptor that checks to see
if the timeout passed, will ensure that it will timeout properly even if
there's input in STDIN.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The run_command function was changed to use the wait_for_input function to
allow having a timeout if the command to run takes too much time. There was
a bug in the wait_for_input where it could end up going into an infinite
loop. There's two issues here. One is that the return value of the sysread
wasn't used for the write (to write a proper size), and that it should
continue processing the passed in file descriptor too even if there was
input. There was no check for error, if for some reason STDIN returned an
error, the function would go into an infinite loop and never exit.
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 6e98d1b441 ("ktest: Add timeout to ssh command")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Pull ktest updates from Steven Rostedt:
"These are various fixes that I have made and never got around to
pushing. I've been asked to get the upstream repo back up-to-date"
* tag 'ktest-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Add variable run_command_status to save status of commands executed
ktest.pl: Powercycle the box on reboot if no connection can be made
ktest: Add timeout to ssh command
ktest: Fix child exit code processing
ktest: Have POST_TEST run after the test has totally completed
Create a variable called run_command_status that saves the status of the
executed commands and can be used by other functions later to test for
status.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
When performing a reboot of the test box, try to ssh to it. If it can't
connect for 5 seconds, then powercycle the box. This is useful because the
reboot is done via ssh, and if you can't ssh to the box because it is hung,
the reboot fails to reboot.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Add a timeout to performing an ssh command. This will let testing if a
machine is alive or not, or if something else may be amiss. A timeout can be
passed to ssh, where ssh will fail if it does not complete within the given
timeout.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The child_exit errno needs to be shifted by 8 bits to compare against the
return values for the bisect variables.
Fixes: c5dacb88f0 ("ktest: Allow overriding bisect test results")
Cc: stable@vger.kernel.org
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The POST_TEST config is to be executed after a test has fully compeleted,
whether the test passed or failed. It currently is executed at the moment
that the test has been decided if it failed or not. As the test does other
clean ups, it isn't truly finished. Move the POST_TEST execution to after
all the test cleanups have been done.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Seems that some of the new console logic causes doprint to possibly
get evaluated. When printing a commit message that contains parenthesis,
it fails with a shell parsing error.
This gets fixed when we add quotes around the $item variable, and prevent
it from being evaluated by any shell commands.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Since both success and failure may shortcut and exit ktest, it is better
to print the status times there too. Once times are printed, the values
for the times are reset, so they will not print more than once.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The function start_monitor_and_boot is a misnomer. It use to, but
now it starts the monitor and installs. It does not boot. Rename it
before I get confused by it again.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Seeing the times for how long a build, install, reboot and the
test takes is helpful for analyzing the test process. Seeing
how different changes affect the timings.
Show the build, install, boot and test times when at the end of
the test, or between each interval for tests that do those
mulitple times (like bisect and patchcheck).
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When ktest runs the console program as a child process, the parent and
child share the same tty for stdin and stderr. This is problematic when
using a libvirt target. The "virsh console" program makes a lot of
changes to the tty settings, making ktest's output hard to read
(carriage returns don't work). After ktest exits, the terminal is
unusable (CRs broken, stdin isn't echoed).
I think the best way to fix this issue would be to create a
pseudoterminal (pty pair) so the child process would have a dedicated
tty, and then use pipes to connect the two ttys. I'm not sure if that's
overkill, but it's far beyond my current Perl abilities.
This patch is a much easier way to (partially) fix this issue. It saves
the tty settings before opening the console and restores them after
closing it. There are still a few places where ktest prints mangled
output while the console is open, but the output is much more legible
overall, and the terminal works just fine after ktest exits.
Link: http://lkml.kernel.org/r/1bb89abc0025cf1d6da657c7ba58bbeb4381a515.1422382008.git.jpoimboe@redhat.com
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
I find that I usually like to see how long a make or other command takes,
and adding a start and end time and reporting how long each command runs
(in seconds) is helpful.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Commit 52d21580b3 "ktest: Use make -s kernelrelease" fixed commit
7ff525712a "kbuild: fake the "Entering directory ..." message more simply"
as that commit added output after the make kernelrelease. But there's still
some build scripts that are used by ktest that has output before the make
is executed, and requires that only the last line is printed.
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Instead of just showing the test type of test in the start of the
test, like this:
RUNNING TEST 1 of 26 with option build defconfig
Add the name (if it is defined) as well, like this:
RUNNING TEST 1 of 26 (arm64 aarch64-linux) with option build defconfig
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Tests can set options that override the default ones. But if a test
tries to undefine a default option, it is simply ignored and the
default option stays as is.
For example, if you want to have a test that defines no MIN_CONFIG
then the test should be able to do that with:
TEST_START
MIN_CONFIG =
Which should make MIN_CONFIG not defined for that test. But the way
the code currently works, undefined options in tests are dropped.
This is because the NULL options are evaluated during the reading of
the config file and since one can disable default options in the default
section with this method, it is evaluated there (the option turns to a
undef). But undef options in the test section mean to use the default
option.
To fix this, keep the empty string in the option during the reading
of the config file, and then evaluate it when running the test. This
will allow tests to null out default options.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Commit 6071c22e17 "ktest: Rewrite the config-bisect to actually work"
fixed the config-bisect to work nicely but in doing so it broke
make_min_config by changing the way assign_configs works.
The assign_configs function now adds the config to the hash even if
it is disabled, but changes the hash value to be that of the
line "# CONFIG_FOO is not set". Unfortunately, the make_min_config
test only checks to see if the config is removed. It now needs to
check if the config is in the hash and not set to be disabled.
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If git bisect reply is being used in the bisect tests, don't bother
doing the git bisect good or git bisect bad calls. The git bisect
reply will override them anyway, and that's called immediately
after the other two. Going the git bisect (good|bad) is just a
waste of time.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
