Pull phy updates from Vinod Koul:
"New hw support:
- Rcar usb2 support for RZ/G3S SoC
- Nuvoton MA35 SoC USB 2.0 PHY driver
Removed:
- obsolete qcom,usb-8x16-phy bindings
Updates:
- 4 lane PCIe support for Qualcomm X1E80100
- Constify structure in subsystem update
- Subsystem simplification with scoped for each OF child loop update
- Yaml conversion for Qualcomm sata phy, Hiilicon hi3798cv200-combphy
bindings"
* tag 'phy-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (40 commits)
phy: renesas: rcar-gen3-usb2: Add support for the RZ/G3S SoC
dt-bindings: phy: renesas,usb2-phy: Document RZ/G3S phy bindings
phy: renesas: rcar-gen3-usb2: Add support to initialize the bus
phy: ti: j721e-wiz: Simplify with scoped for each OF child loop
phy: ti: j721e-wiz: Drop OF node reference earlier for simpler code
phy: ti: gmii-sel: Simplify with dev_err_probe()
phy: ti: am654-serdes: Use scoped device node handling to simplify error paths
phy: qcom: qmp-pcie-msm8996: Simplify with scoped for each OF child loop
phy: mediatek: xsphy: Simplify with scoped for each OF child loop
phy: mediatek: tphy: Simplify with scoped for each OF child loop
phy: hisilicon: usb2: Simplify with scoped for each OF child loop
phy: cadence: sierra: Simplify with scoped for each OF child loop
phy: broadcom: brcm-sata: Simplify with scoped for each OF child loop
phy: broadcom: bcm-cygnus-pcie: Simplify with scoped for each OF child loop
phy: nuvoton: add new driver for the Nuvoton MA35 SoC USB 2.0 PHY
dt-bindings: phy: nuvoton,ma35-usb2-phy: add new bindings
phy: qcom: qmp-pcie: Configure all tables on port B PHY
phy: airoha: adjust initialization delay in airoha_pcie_phy_init()
dt-bindings: phy: socionext,uniphier: add top-level constraints
phy: qcom: qmp-pcie: Add Gen4 4-lanes mode for X1E80100
...
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- introduce power_supply_show_enum_with_available() helper
- change usb_types from an array into a bitmask
- fix early usage of power_supply_property_is_writeable() resulting
in sysfs files not being writable
- fix missing temp1_max_alarm attribute in power-supply's hwmon
devices
Drivers:
- max1720x: expose nvmem device
- brcmstb: cleanup driver to use latest APIs
- max77693: expose input and charging current limit
- max17042_battery: fix state of charge reading for devices without
current sensing
- axp20x_battery: add AXP717 support
- axp20x_battery: fix min/max voltage properties
- axp20x_usb_power: add AXP717 support
- axp20x_usb_power: add DT based input current limit
Documentation updates
Misc minor cleanups and fixes"
* tag 'for-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (38 commits)
power: supply: hwmon: Fix missing temp1_max_alarm attribute
power: supply: Drop use_cnt check from power_supply_property_is_writeable()
power: supply: ab8500: Constify struct kobj_type
power: supply: max1720x: fix a double free on error in probe()
power: supply: axp20x_battery: add support for AXP717
power: supply: axp20x_usb_power: Add support for AXP717
dt-bindings: power: supply: axp20x: Add AXP717 compatible
dt-bindings: power: supply: axp20x: Add AXP717 compatible
power: supply: axp20x_usb_power: Fix spelling mistake "reqested" -> "requested"
power: supply: Change usb_types from an array into a bitmask
power: supply: sysfs: Move power_supply_show_enum_with_available() up
power: supply: sysfs: Add power_supply_show_enum_with_available() helper
power: supply: rt9467-charger: Remove "usb_type" property write support
power: supply: ucs1002: Adjust ucs1002_set_usb_type() to accept string values
power: supply: "usb_type" property may be written to
power: supply: max1720x: add read support for nvmem
mfd: axp20x: Add ADC, BAT, and USB cells for AXP717
power: supply: core: constify psy_tzd_ops
power: reset: brcmstb: Do not go into infinite loop if reset fails
power: reset: brcmstb: Use devm_register_sys_off_handler()
...
The bit_types array just hold a list of valid enum power_supply_usb_type
values which map to 0 - 9. This can easily be represented as a bitmap.
This reduces the size of struct power_supply_desc and further reduces
the data section size by drivers no longer needing to store the array.
This also unifies how usb_types are handled with charge_behaviours,
which allows power_supply_show_usb_type() to be removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240831142039.28830-7-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The Renesas RZ/G3S need to initialize the USB BUS before transferring data
due to hardware limitation. As the register that need to be touched for
this is in the address space of the USB PHY, and the UBS PHY need to be
initialized before any other USB drivers handling data transfer, add
support to initialize the USB BUS.
As the USB PHY is probed before any other USB drivers that enables
clocks and de-assert the reset signals and the BUS initialization is done
in the probe phase, we need to add code to de-assert reset signal and
runtime resume the device (which enables its clocks) before accessing
the registers.
As the reset signals are not required by the USB PHY driver for the other
USB PHY hardware variants, the reset signals and runtime PM was handled
only in the function that initialize the USB BUS.
The PHY initialization was done right after runtime PM enable to have
all in place when the PHYs are registered.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240822152801.602318-11-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On a few Kria KR260 Robotics Starter Kit the PS-GEM SGMII linkup is not
happening after the resume. This is because serdes registers are reset
when FPD is off (in suspend state) and needs to be reprogrammed in the
resume path with the same default initialization as done in the first
stage bootloader psu_init routine.
To address the failure introduce a set of serdes registers to be saved in
the suspend path and then restore it on resume.
Fixes: 4a33bea003 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver")
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1722837547-2578381-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The HDMI PHY PLL can be used as an alternative dclk source to RK3588 SoC
CRU. It provides more accurate clock rates required by VOP2 to improve
existing support for display modes handling, which is known to be
problematic when dealing with non-integer refresh rates, among others.
It is worth noting this only works for HDMI 2.0 or below, e.g. cannot be
used to support HDMI 2.1 4K@120Hz mode.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240620-rk3588-hdmiphy-clkprov-v2-4-6a2d2164e508@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When a new PHY is created via [devm_]phy_create(), the runtime PM for it
is not enabled unless the parent device (which creates the PHY) has its
own runtime PM already enabled.
Move the call to devm_pm_runtime_enable() before devm_phy_create() to
enable runtime PM at PHY core level.
With this change the ->power_on() and ->power_off() callbacks do not
require explicit runtime PM management anymore, since the PHY core
handles that via phy_pm_runtime_{get,put}_sync() when phy_power_on() and
phy_power_off() are invoked.
Hence drop the now unnecessary calls to pm_runtime_resume_and_get() and
pm_runtime_put() helpers.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240620-rk3588-hdmiphy-clkprov-v2-2-6a2d2164e508@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Torrent SERDES can support at most two different protocols (PHY types).
This only mandates that the device-tree sub-nodes used to represent the
configuration should describe links with at-most two different protocols.
The existing implementation however imposes an artificial constraint that
allows only two links (device-tree sub-nodes). As long as at-most two
protocols are chosen, using more than two links to describe them in an
alternating configuration is still a valid configuration of the Torrent
SERDES.
A 3-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 1 => Link 1
Lane 2 => Protocol 2 => Link 2
Lane 3 => Protocol 1 => Link 3
A 4-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 2 => Link 2
Lane 2 => Protocol 1 => Link 3
Lane 3 => Protocol 2 => Link 4
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240805092607.143869-1-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
