Enclose the runtime PM helpers in #ifdef CONFIG_PM_RUNTIME/#endif
to avoid following compile warning when CONFIG_PM_RUNTIME is disabled:
CC drivers/media/platform/exynos4-is/fimc-lite.o
drivers/media/platform/exynos4-is/fimc-lite.c:1591:12: warning: ‘fimc_lite_runtime_resume’ defined but not used [-Wunused-function]
drivers/media/platform/exynos4-is/fimc-lite.c:1599:12: warning: ‘fimc_lite_runtime_suspend’ defined but not used [-Wunused-function]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Enclose the runtime PM helpers in #ifdef CONFIG_PM_RUNTIME/#endif
to avoid following compile warning when CONFIG_PM_RUNTIME is disabled:
CC drivers/media/platform/exynos4-is/fimc-core.o
drivers/media/platform/exynos4-is/fimc-core.c:1040:12: warning: ‘fimc_runtime_resume’ defined but not used
drivers/media/platform/exynos4-is/fimc-core.c:1057:12: warning: ‘fimc_runtime_suspend’ defined but not used
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ensure clk_disable() is called on error paths only when clk_enable()
was previously called.
This fixes following build warning:
.../media-git/drivers/media/platform/exynos4-is/fimc-lite.c: In function 'fimc_lite_probe':
.../media-git/drivers/media/platform/exynos4-is/fimc-lite.c:1583:1: warning: label 'err_sd' defined but not used [-Wunused-label]
Reported-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
- a new jpeg codec driver for Samsung Exynos (jpeg-hw-exynos4)
- a new dvb frontend for ds2103 chipset (m88ds2103)
- a new sensor driver for Samsung S5K5BAF UXGA (s5k5baf)
- new drivers for R-Car VSP1
- a new radio driver: radio-raremono
- a new tuner driver for ts2022 chipset (m88ts2022)
- the analog part of em28xx is now a separate module that only
load/runs if the device is not a pure digital TV device
- added a staging driver for bcm2048 radio devices
- the omap 2 video driver (omap24xx) was moved to staging. This driver
is for an old hardware and uses a deprecated Kernel internal API. If
nobody cares enough to fix it, it would be removed on a couple Kernel
releases
- the sn9c102 driver was moved to staging. This driver was replaced by
gspca, and disabled on some distros, as almost all devices are known
to work properly with gspca. It should be removed from kernel on a
couple Kernel releases
- lots of driver fixes, improvements and cleanups
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (421 commits)
[media] media: v4l2-dev: fix video device index assignment
[media] rc-core: reuse device numbers
[media] em28xx-cards: properly initialize the device bitmap
[media] Staging: media: Fix line length exceeding 80 characters in as102_drv.c
[media] Staging: media: Fix line length exceeding 80 characters in as102_fe.c
[media] Staging: media: Fix quoted string split across line in as102_fe.c
[media] media: st-rc: Add reset support
[media] m2m-deinterlace: fix allocated struct type
[media] radio-usb-si4713: fix sparse non static symbol warnings
[media] em28xx-audio: remove needless check before usb_free_coherent()
[media] au0828: Fix sparse non static symbol warning
Revert "[media] go7007-usb: only use go->dev after allocated"
[media] em28xx-audio: provide an error code when URB submit fails
[media] em28xx: fix check for audio only usb interfaces when changing the usb alternate setting
[media] em28xx: fix usb alternate setting for analog and digital video endpoints > 0
[media] em28xx: make 'em28xx_ctrl_ops' static
em28xx-alsa: Fix error patch for init/fini
[media] em28xx-audio: flush work at .fini
[media] drxk: remove the option to load firmware asynchronously
[media] em28xx: adjust period size at runtime
...
<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>
Pull clk framework changes from Mike Turquette:
"The first half of the clk framework pull request is made up almost
entirely of new platform/driver support. There are some conversions
of existing drivers to the common-clock Device Tree binding, and a few
non-critical fixes to the framework.
Due to an entirely unnecessary cyclical dependency with the arm-soc
tree this pull request is broken into two pieces. The second piece
will be sent out after arm-soc sends you the pull request that merged
in core support for the HiSilicon 3620 platform. That same pull
request from arm-soc depends on this pull request to merge in those
HiSilicon bits without causing build failures"
[ Just did the ARM SoC merges, so getting ready for the second clk tree
pull request - Linus ]
* tag 'clk-for-linus-3.14-part1' of git://git.linaro.org/people/mike.turquette/linux: (97 commits)
devicetree: bindings: Document qcom,mmcc
devicetree: bindings: Document qcom,gcc
clk: qcom: Add support for MSM8660's global clock controller (GCC)
clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC)
clk: qcom: Add support for MSM8974's global clock controller (GCC)
clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)
clk: qcom: Add support for MSM8960's global clock controller (GCC)
clk: qcom: Add reset controller support
clk: qcom: Add support for branches/gate clocks
clk: qcom: Add support for root clock generators (RCGs)
clk: qcom: Add support for phase locked loops (PLLs)
clk: qcom: Add a regmap type clock struct
clk: Add set_rate_and_parent() op
reset: Silence warning in reset-controller.h
clk: sirf: re-arch to make the codes support both prima2 and atlas6
clk: composite: pass mux_hw into determine_rate
clk: shmobile: Fix MSTP clock array initialization
clk: shmobile: Fix MSTP clock index
ARM: dts: Add clock provider specific properties to max77686 node
clk: max77686: Register OF clock provider
...
'xt' points to a dma_interleaved_template and not a dma_async_tx_descriptor.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix two warns below, by commenting the unused code:
drivers/media/platform/sh_vou.c: In function 'sh_vou_configure_geometry':
drivers/media/platform/sh_vou.c:446:49: warning: variable 'height_max' set but not used [-Wunused-but-set-variable]
unsigned int black_left, black_top, width_max, height_max,
^
drivers/media/platform/sh_vou.c: In function 'sh_vou_isr':
drivers/media/platform/sh_vou.c:1056:13: warning: variable 'side' set but not used [-Wunused-but-set-variable]
static int side;
^
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add v4l2 controls to set desired profile for VP8 encoder.
Acceptable levels for VP8 encoder are
0: Version 0
1: Version 1
2: Version 2
3: Version 3
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
s5p_mfc_get_node_type() relies on get_index() helper function, which in
turn relies on video_device index numbers assigned on driver
registration. All this code is not really needed, because there is
already access to respective video_device structures via common
s5p_mfc_dev structure. This fixes the issues introduced by patch
1056e4388b ("v4l2-dev: Fix race condition
on __video_register_device"), which has been merged in v3.12-rc1.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
after device tree based clock lookup became available, the VIU driver
need no longer use the previous global "viu_clk" name, but should use
the "ipg" clock name specific to the OF node
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This adds R-Car M2 (R8A7791) VIN support. Both H2 and M2
variants look the same from the driver's point of view,
so use GEN2 id for both.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[g.liakhovetski@gmx.de: removed changelog from commit message]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Under abnormal conditions (such as glitches on the HSYNC/VSYNC signals)
the CCDC output SBL can fail to become idle. The driver currently logs
this condition to the kernel log and doesn't restart the CCDC. This
results in CCDC video capture hanging without any notification to
userspace.
Cancel the pipeline and mark the CCDC as crashed instead of hanging.
Userspace will be notified of the problem and will then be able to close
and reopen the device to trigger a reset of the ISP.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modules failing to stop are fatal errors for the preview engine only.
Flag that condition separately from the other stop failures to prepare
support for more fatal errors.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When a fatal error that prevents any further video streaming occurs in a
pipeline, all queued buffers must be marked as erroneous and new buffers
must be prevented from being queued. Implement this behaviour with a new
omap3isp_pipeline_cancel_stream() function that can be used by
submodules to cancel streaming.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As discussed on the media summit 2013, there is no reason for the width
and height to be signed.
Therefore this patch is an attempt to convert those fields from __s32 to
__u32.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi> (documentation and smiapp)
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The struct vpdma_data_format holds the color format depth and the data_type
value needed to be programmed in the data descriptors. However, it doesn't
tell what type of color format is it, i.e, whether it is RGB, YUV or Misc.
This information is needed when by vpdma library when forming descriptors. We
modify the depth parameter for the chroma portion of the NV12 format. For this,
we check if the data_type value is C420. This isn't sufficient as there are
many YUV and RGB vpdma formats which have the same data_type value. Hence, we
need to hold the type of the color format for the above case, and possibly more
cases in the future.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the csc library functions to configure the CSC block in VPE.
Some changes are required in try_fmt to handle the pix->colorspace parameter
more correctly. Previously, we copied the source queue colorspace to the
destination queue colorspace as we didn't support RGB formats. Now, we configure
pix->colorspace based on the color format set(and the height of the image if
it's a YUV format).
Add basic RGB color formats to the list of supported vpe formats.
If the destination format is RGB colorspace, we also need to use the RGB output
port instead of the Luma and Chroma output ports. This requires configuring the
output data descriptors differently.
Also, make the default colorspace V4L2_COLORSPACE_SMPTE170M as that resembles
the Standard Definition colorspace more closely.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The CSC block can be used for color space conversion between YUV and RGB
formats.
It is configurable via a programmable set of coefficients. Add functionality to
choose the appropriate CSC coefficients and program them in the CSC registers.
We take the source and destination colorspace formats as the arguments, and
choose the coefficient table accordingly.
YUV to RGB coefficients are provided for standard and high definition
colorspaces. The coefficients can also be limited or full range. For now, only
full range coefficients are chosen. We would need some sort of control ioctl for
the user to specify the range needed. Not sure if there is a generic control
ioctl for this already?
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VPE and VIP IPs in DAR7x contain a color space converter(CSC) sub block. Create
a library which will perform CSC related configurations and hold CSC register
definitions. The functions provided by this library will be called by the vpe
and vip drivers using a csc_data handle.
The vpe_dev holds the csc_data handle. The handle represents an instance of the
CSC hardware, and the vpe driver uses it to access the CSC register offsets or
helper functions to configure these registers.
The CSC register offsets are now relative to the CSC block itself, so we need
to use the macro GET_OFFSET_TOP to get the CSC register offset relative to the
VPE IP in the vpe driver.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add the required SC register configurations which lets us perform linear scaling
for the supported range of horizontal and vertical scaling ratios.
The horizontal scaler performs polyphase scaling using it's 8 tap 32 phase
filter, decimation is performed when downscaling passes beyond 2x or 4x.
The vertical scaler performs polyphase scaling using it's 5 tap 32 phase filter,
it switches to a simpler form of scaling using the running average filter when
the downscale ratio is more than 4x.
Many of the SC features like peaking, trimming and non-linear scaling aren't
implemented for now. Only the minimal register fields required for basic scaling
operation are configured.
The function to configure SC registers takes the sc_data handle, the source and
destination widths and heights, and the scaler address data block offsets for
the current context so that they can be configured.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Make the driver allocate dma buffers to store horizontal and scaler coeffs.
Use the scaler library api to choose and copy scaler coefficients to a
the above buffers based on the scaling ratio. Since the SC block comes after
the de-interlacer, make sure that the source height is doubled if de-interlacer
was used.
These buffers now need to be used by VPDMA to load the coefficients into the
SRAM within SC.
In device_run, add configuration descriptors which have payloads pointing to
the scaler coefficients in memory. Use the members in sc_data handle to prevent
addition of these descriptors if there isn't a need to re-load coefficients into
SC. This comes helps unnecessary re-loading of the coefficients when we switch
back and forth between vpe contexts.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
