We're now blacklisting "Crucial_CT???M500SSD1" and
"Crucial_CT???M500SSD3". Also, "Micron_M500*" is blacklisted which is
about the same devices as the crucial branded ones. Let's merge the
two Crucial M500 entries and widen the match to
"Crucial_CT???M500SSD*" so that we don't have to fiddle with new
entries for similar devices.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
For some reason, some early WD drives spin up and down drives
erratically when the link is put into slumber mode which can reduce
the life expectancy of the device significantly. Unfortunately, we
don't have full list of devices and given the nature of the issue it'd
be better to err on the side of false positives than the other way
around. Let's disable LPM on all WD devices which match one of the
known problematic model prefixes and are SATA-I.
As horkage list doesn't support matching SATA capabilities, this is
implemented as two horkages - WD_BROKEN_LPM and NOLPM. The former is
set for the known prefixes and sets the latter if the matched device
is SATA-I.
Note that this isn't optimal as this disables all LPM operations and
partial link power state reportedly works fine on these; however, the
way LPM is implemented in libata makes it difficult to precisely map
libata LPM setting to specific link power state. Well, these devices
are already fairly outdated. Let's just disable whole LPM for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Nikos Barkas <levelwol@gmail.com>
Reported-and-tested-by: Ioannis Barkas <risc4all@yahoo.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=57211
Cc: stable@vger.kernel.org
Certain drives cannot handle queued TRIM commands properly, even
though support is indicated in the IDENTIFY DEVICE buffer. This patch
allows for disabling the commands for the affected drives and apply it
to the Micron/Crucial M500 SSDs which exhibit incorrect protocol
behavior when issued queued TRIM commands, which could lead to silent
data corruption.
tj: Merged two unnecessarily split patches and made minor edits
including shortening horkage name.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/g/1387246554-7311-1-git-send-email-marc.ceeeee@gmail.com
Cc: stable@vger.kernel.org # 3.12+
We've received multiple reports in Fedora via (BZ 907193)
that the Seagate Momentus SpinPoint M8 errors out when enabling AA:
[ 2.555905] ata2.00: failed to enable AA (error_mask=0x1)
[ 2.568482] ata2.00: failed to enable AA (error_mask=0x1)
Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk.
Reported-by: Nicholas <arealityfarbetween@googlemail.com>
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Tested-by: Nicholas <arealityfarbetween@googlemail.com>
Acked-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
After commit bcdde7e221 (sysfs: make __sysfs_remove_dir() recursive)
Mika Westerberg sees traces analogous to the one below in Thunderbolt
hot-remove testing:
WARNING: CPU: 0 PID: 4 at fs/sysfs/group.c:214 sysfs_remove_group+0xc6/0xd0()
sysfs group ffffffff81c6f1e0 not found for kobject 'host7'
Modules linked in:
CPU: 0 PID: 4 Comm: kworker/0:0 Not tainted 3.12.0+ #13
Hardware name: /D33217CK, BIOS GKPPT10H.86A.0042.2013.0422.1439 04/22/2013
Workqueue: kacpi_hotplug acpi_hotplug_work_fn
0000000000000009 ffff8801002459b0 ffffffff817daab1 ffff8801002459f8
ffff8801002459e8 ffffffff810436b8 0000000000000000 ffffffff81c6f1e0
ffff88006d440358 ffff88006d440188 ffff88006e8b4c28 ffff880100245a48
Call Trace:
[<ffffffff817daab1>] dump_stack+0x45/0x56
[<ffffffff810436b8>] warn_slowpath_common+0x78/0xa0
[<ffffffff81043727>] warn_slowpath_fmt+0x47/0x50
[<ffffffff811ad319>] ? sysfs_get_dirent_ns+0x49/0x70
[<ffffffff811ae526>] sysfs_remove_group+0xc6/0xd0
[<ffffffff81432f7e>] dpm_sysfs_remove+0x3e/0x50
[<ffffffff8142a0d0>] device_del+0x40/0x1b0
[<ffffffff8142a24d>] device_unregister+0xd/0x20
[<ffffffff8144131a>] scsi_remove_host+0xba/0x110
[<ffffffff8145f526>] ata_host_detach+0xc6/0x100
[<ffffffff8145f578>] ata_pci_remove_one+0x18/0x20
[<ffffffff812e8f48>] pci_device_remove+0x28/0x60
[<ffffffff8142d854>] __device_release_driver+0x64/0xd0
[<ffffffff8142d8de>] device_release_driver+0x1e/0x30
[<ffffffff8142d257>] bus_remove_device+0xf7/0x140
[<ffffffff8142a1b1>] device_del+0x121/0x1b0
[<ffffffff812e43d4>] pci_stop_bus_device+0x94/0xa0
[<ffffffff812e437b>] pci_stop_bus_device+0x3b/0xa0
[<ffffffff812e437b>] pci_stop_bus_device+0x3b/0xa0
[<ffffffff812e44dd>] pci_stop_and_remove_bus_device+0xd/0x20
[<ffffffff812fc743>] trim_stale_devices+0x73/0xe0
[<ffffffff812fc78b>] trim_stale_devices+0xbb/0xe0
[<ffffffff812fc78b>] trim_stale_devices+0xbb/0xe0
[<ffffffff812fcb6e>] acpiphp_check_bridge+0x7e/0xd0
[<ffffffff812fd90d>] hotplug_event+0xcd/0x160
[<ffffffff812fd9c5>] hotplug_event_work+0x25/0x60
[<ffffffff81316749>] acpi_hotplug_work_fn+0x17/0x22
[<ffffffff8105cf3a>] process_one_work+0x17a/0x430
[<ffffffff8105db29>] worker_thread+0x119/0x390
[<ffffffff8105da10>] ? manage_workers.isra.25+0x2a0/0x2a0
[<ffffffff81063a5d>] kthread+0xcd/0xf0
[<ffffffff81063990>] ? kthread_create_on_node+0x180/0x180
[<ffffffff817eb33c>] ret_from_fork+0x7c/0xb0
[<ffffffff81063990>] ? kthread_create_on_node+0x180/0x180
The source of this problem is that SCSI hosts are removed from
ATA ports after calling ata_tport_delete() which removes the
port's sysfs directory, among other things. Now, after commit
bcdde7e221, the sysfs directory is removed along with all of
its subdirectories that include the SCSI host's sysfs directory
and its subdirectories at this point. Consequently, when
device_del() is finally called for any child device of the SCSI
host and tries to remove its "power" group (which is already
gone then), it triggers the above warning.
To make the warnings go away, change the removal ordering in
ata_port_detach() so that the SCSI host is removed from the
port before ata_tport_delete() is called.
References: https://bugzilla.kernel.org/show_bug.cgi?id=65281
Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The endianness attribute on the 'aux' local variable is wrong, and can
lead to wrong endianness on big-endian machines,
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add support for the following ATA opcodes, which are present
in SATA 3.1 and T13 ATA ACS-3:
SEND FPDMA QUEUED
RECEIVE FPDMA QUEUED
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
SATA 3.1 added an "auxiliary" field to the host-to-device FIS.
Populate the host-to-device FIS with the new field via the
taskfile struct.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Binding ACPI handle to SCSI device has several drawbacks, namely:
1 During ATA device initialization time, ACPI handle will be needed
while SCSI devices are not created yet. So each time ACPI handle is
needed, instead of retrieving the handle by ACPI_HANDLE macro,
a namespace scan is performed to find the handle for the corresponding
ATA device. This is inefficient, and also expose a restriction on
calling path not holding any lock.
2 The binding to SCSI device tree makes code complex, while at the same
time doesn't bring us any benefit. All ACPI handlings are still done
in ATA module, not in SCSI.
Rework the ATA ACPI binding code to bind ACPI handle to ATA transport
devices(ATA port and ATA device). The binding needs to be done only once,
since the ATA transport devices do not go away with hotplug. And due to
this, the flush_work call in hotplug handler for ATA bay is no longer
needed.
Tested on an Intel test platform for binding and runtime power off for
ODD(ZPODD) and hard disk; on an ASUS S400C for binding and normal boot
and S3, where its SATA port node has _SDD and _GTF control methods when
configured as an AHCI controller and its PATA device node has _GTF
control method when configured as an IDE controller. SATA PMP binding
and ATA hotplug is not tested.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Dirk Griesbach <spamthis@freenet.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Overview of changes:
- The rest of maintainer email address updates.
- Some core updates - more robust default behavior for port
multipliers, better error reporting for SG_IO commands, and a way
to better work around now ancient and probably pretty rare PATA ->
SATA bridges with ATAPI devices.
- sata_rcar stabilization.
- Some hardware PCI ID additions and one-off low level driver
updates."
* 'for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
AHCI: use ATA_BUSY
libata-zpodd: must use ata_tf_init()
ahci: AHCI-mode SATA patch for Intel Coleto Creek DeviceIDs
ata_piix: IDE-mode SATA patch for Intel Coleto Creek DeviceIDs
libata: cleanup SAT error translation
ahci: sata: add support for exynos5440 sata
libata: skip SRST for all SIMG [34]7x port-multipliers
ahci: remove pmp link online check in FBS EH
sata highbank: add bit-banged SGPIO driver support
ahci: make ahci_transmit_led_message into a function pointer
sata_rcar: fix compilation warning in sata_rcar_thaw()
sata_highbank: increase retry count but shorten duration for Calxeda controller
ata: use pci_get_drvdata()
ipr: qc_fill_rtf() method should not store alternate status register
sata_rcar: add 'base' local variable to some functions
sata_rcar: correct 'sata_rcar_sht'
sata_rcar: kill superfluous code in sata_rcar_bmdma_fill_sg()
libata: do not limit R-Car SATA driver to shmobile
ata: use platform_{get,set}_drvdata()
AHCI: Make distinct names for ports in /proc/interrupts
...
libata/for-3.10-fixes never got submitted during v3.10 cycle. Merge
it into for-3.11 so that it can be routed together with other changes
scheduled for v3.11.
Three trivial conflicts in drivers/ata/sata_rcar.c. All are caused by
1b20f6a9ad ("sata_rcar: add 'base' local variable to some functions")
conflicting with logic updates in for-3.10-fixes. The offending
commit simply adds local variable @base on functions which
dereferences sata_rcar_priv->base multiple times. The resolutions are
trivial - applying s/priv->base/base/ in the conflicting logic
updates.
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 30dcf76acc "libata: migrate ACPI code over to new bindings"
mistakenly dropped the code to register hotplug notificaion handler
for ATA port/devices, causing regression for people using ATA bay,
as kernel bug #59871 shows.
Fix this by adding back the hotplug notification handler registration
code. Since this code has to be run once and notification needs to
be installed on every ATA port/devices handle no matter if there is
actual device attached, we can't do this in binding time for ATA
device ACPI handle, as the binding only occurs when a SCSI device is
created, i.e. there is device attached. So introduce the
ata_acpi_hotplug_init() function to loop scan all ATA ACPI handles
and if it is available, install the notificaion handler for it during
ATA init time.
With the ATA ACPI handle binding to SCSI device tree, it is possible
now that when the SCSI hotplug work removes the SCSI device, the ACPI
unbind function will find that the corresponding ACPI device has
already been deleted by dock driver, causing a scaring message like:
[ 128.263966] scsi 4:0:0:0: Oops, 'acpi_handle' corrupt
Fix this by waiting for SCSI hotplug task finish in our notificaion
handler, so that the removal of ACPI device done in ACPI unbind
function triggered by the removal of SCSI device is run earlier when
ACPI device is still available.
[rjw: Rebased]
References: https://bugzilla.kernel.org/show_bug.cgi?id=59871
Reported-bisected-and-tested-by: Dirk Griesbach <spamthis@freenet.de>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: 3.6+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Some device require DMADIR to be enabled, but are not detected as such
by atapi_id_dmadir. One such example is "Asus Serillel 2"
SATA-host-to-PATA-device bridge: the bridge itself requires DMADIR,
even if the bridged device does not.
As atapi_dmadir module parameter can cause problems with some devices
(as per Tejun Heo's memory), enabling it globally may not be possible
depending on the hardware.
This patch adds atapi_dmadir in the form of a "force" horkage value,
allowing global, per-bus and per-device control.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
While registering host controller track port number based upon number
of ports available on the controller, export port_no attribute through
/sys. This patch is needed by udev for composing persistent links in
/dev/disk/by-path.
/sys/devices/pci0000:00/0000:00:1f.2/ata8/ata_port/ata8
total 0
lrwxrwxrwx. 1 root root 0 Mar 6 12:43 device -> ../../../ata8
-r--r--r--. 1 root root 4096 Mar 6 12:43 idle_irq
-r--r--r--. 1 root root 4096 Mar 6 12:43 nr_pmp_links
-r--r--r--. 1 root root 4096 Mar 6 12:43 port_no
drwxr-xr-x. 2 root root 0 Mar 6 12:42 power
lrwxrwxrwx. 1 root root 0 Mar 6 12:41 subsystem -> ../../../../../../class/ata_port
-rw-r--r--. 1 root root 4096 Mar 6 12:40 uevent
1
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Jeff moved on to a greener pasture.
s/Maintained by: Jeff Garzik/Maintained by: Tejun Heo/g
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Commit 803739d25c ("[libata] replace
sata_settings with devslp_timing"), which was also Cc: stable, used a
stack buffer to receive data from ata_read_log_page(), which triggers
the following warning:
ahci 0000:00:1f.2: DMA-API: device driver maps memory fromstack [addr=ffff880140469948]
Fix this by using ap->sector_buf instead of a stack buffer.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For system freeze, if the port is already runtime suspended, leave it
alone and just return. The port will be resumed on thaw before it will
be used.
And since we will call get_noresume for every device during prepare
phase, and the port is resumed during thaw phase, it can't be in runtime
suspended state during the poweroff phase. So remove the
runtime_suspended check in poweroff callback.
And for all suspend(freeze/suspend/poweroff/etc.), there is no need to
touch the device, so set no_autopsy and no_recovery for them all.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
