It is possible to stack multiple DSA switches in a way that they are not
part of the tree (disjoint) but the DSA master of a switch is a DSA
slave of another. When that happens switch drivers may have to know this
is the case so as to determine whether their tagging protocol has a
remove chance of working.
This is useful for specific switch drivers such as b53 where devices
have been known to be stacked in the wild without the Broadcom tag
protocol supporting that feature. This allows b53 to continue supporting
those devices by forcing the disabling of Broadcom tags on the outermost
switches if necessary.
The get_tag_protocol() function is therefore updated to gain an
additional enum dsa_tag_protocol argument which denotes the current
tagging protocol used by the DSA master we are attached to, else
DSA_TAG_PROTO_NONE for the top of the dsa_switch_tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 3 things that are wrong with the DSA deferred xmit mechanism:
1. Its introduction has made the DSA hotpath ever so slightly more
inefficient for everybody, since DSA_SKB_CB(skb)->deferred_xmit needs
to be initialized to false for every transmitted frame, in order to
figure out whether the driver requested deferral or not (a very rare
occasion, rare even for the only driver that does use this mechanism:
sja1105). That was necessary to avoid kfree_skb from freeing the skb.
2. Because L2 PTP is a link-local protocol like STP, it requires
management routes and deferred xmit with this switch. But as opposed
to STP, the deferred work mechanism needs to schedule the packet
rather quickly for the TX timstamp to be collected in time and sent
to user space. But there is no provision for controlling the
scheduling priority of this deferred xmit workqueue. Too bad this is
a rather specific requirement for a feature that nobody else uses
(more below).
3. Perhaps most importantly, it makes the DSA core adhere a bit too
much to the NXP company-wide policy "Innovate Where It Doesn't
Matter". The sja1105 is probably the only DSA switch that requires
some frames sent from the CPU to be routed to the slave port via an
out-of-band configuration (register write) rather than in-band (DSA
tag). And there are indeed very good reasons to not want to do that:
if that out-of-band register is at the other end of a slow bus such
as SPI, then you limit that Ethernet flow's throughput to effectively
the throughput of the SPI bus. So hardware vendors should definitely
not be encouraged to design this way. We do _not_ want more
widespread use of this mechanism.
Luckily we have a solution for each of the 3 issues:
For 1, we can just remove that variable in the skb->cb and counteract
the effect of kfree_skb with skb_get, much to the same effect. The
advantage, of course, being that anybody who doesn't use deferred xmit
doesn't need to do any extra operation in the hotpath.
For 2, we can create a kernel thread for each port's deferred xmit work.
If the user switch ports are named swp0, swp1, swp2, the kernel threads
will be named swp0_xmit, swp1_xmit, swp2_xmit (there appears to be a 15
character length limit on kernel thread names). With this, the user can
change the scheduling priority with chrt $(pidof swp2_xmit).
For 3, we can actually move the entire implementation to the sja1105
driver.
So this patch deletes the generic implementation from the DSA core and
adds a new one, more adequate to the requirements of PTP TX
timestamping, in sja1105_main.c.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds glue logic to make pause settings per port
configurable vie ethtool.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some interface types could be nested.
(VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, VIRT_WIFI, VXLAN, etc..)
These interface types should set lockdep class because, without lockdep
class key, lockdep always warn about unexisting circular locking.
In the current code, these interfaces have their own lockdep class keys and
these manage itself. So that there are so many duplicate code around the
/driver/net and /net/.
This patch adds new generic lockdep keys and some helper functions for it.
This patch does below changes.
a) Add lockdep class keys in struct net_device
- qdisc_running, xmit, addr_list, qdisc_busylock
- these keys are used as dynamic lockdep key.
b) When net_device is being allocated, lockdep keys are registered.
- alloc_netdev_mqs()
c) When net_device is being free'd llockdep keys are unregistered.
- free_netdev()
d) Add generic lockdep key helper function
- netdev_register_lockdep_key()
- netdev_unregister_lockdep_key()
- netdev_update_lockdep_key()
e) Remove unnecessary generic lockdep macro and functions
f) Remove unnecessary lockdep code of each interfaces.
After this patch, each interface modules don't need to maintain
their lockdep keys.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA currently handles shared block filters (for the classifier-action
qdisc) in the core due to what I believe are simply pragmatic reasons -
hiding the complexity from drivers and offerring a simple API for port
mirroring.
Extend the dsa_slave_setup_tc function by passing all other qdisc
offloads to the driver layer, where the driver may choose what it
implements and how. DSA is simply a pass-through in this case.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding a VLAN sub-interface on a DSA slave port, the 8021q core
checks NETIF_F_HW_VLAN_CTAG_FILTER and, if the netdev is capable of
filtering, calls .ndo_vlan_rx_add_vid or .ndo_vlan_rx_kill_vid to
configure the VLAN offloading.
DSA sets this up counter-intuitively: it always advertises this netdev
feature, but the underlying driver may not actually support VLAN table
manipulation. In that case, the DSA core is forced to ignore the error,
because not being able to offload the VLAN is still fine - and should
result in the creation of a non-accelerated VLAN sub-interface.
Change this so that the netdev feature is only advertised for switch
drivers that support VLAN manipulation, instead of checking for
-EOPNOTSUPP at runtime.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bridge offloads a VLAN on a slave port, we also need to
program its dedicated CPU port as a member of the VLAN.
Drivers may handle the CPU port's membership as they want. For example,
Marvell as a special "Unmodified" mode to pass frames as is through
such ports.
Even though DSA expects the drivers to handle the CPU port membership,
it does not make sense to program user VLANs as PVID on the CPU port.
This patch clears this flag before programming the CPU port.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA currently programs a VLAN on the CPU port implicitly after the
related notifier is received by a switch.
While we still need to do this transparent programmation of the DSA
links in the fabric, programming the CPU port this way may cause
problems in some corners such as the tag_8021q driver.
Because the dedicated CPU port is specific to a slave, make their
programmation explicit a few layers up, in the slave code.
Note that technically, DSA links have a dedicated CPU port as well,
but since they are only used as conduit between interconnected switches
of a fabric, programming them transparently this way is what we want.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge VLANs are not offloaded by dsa_port_vlan_* if the port is
not bridged or if its bridge is not VLAN aware.
This is a good thing but other corners of DSA, such as the tag_8021q
driver, may need to program VLANs regardless the bridge state.
And also because bridge_dev is specific to user ports anyway, move
these checks were it belongs, one layer up in the slave code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dsa_slave_vlan_add and dsa_slave_vlan_del helpers to handle
SWITCHDEV_OBJ_ID_PORT_VLAN switchdev objects. Also copy the
switchdev_obj_port_vlan structure on add since we will modify it in
future patches.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently dsa_port_vid_add returns 0 if the switch returns -EOPNOTSUPP.
This function is used in the tag_8021q.c code to offload the PVID of
ports, which would simply not work if .port_vlan_add is not supported
by the underlying switch.
Do not skip -EOPNOTSUPP in dsa_port_vid_add but only when necessary,
that is to say in dsa_slave_vlan_rx_add_vid.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This object stores the flow block callbacks that are attached to this
block. Update flow_block_cb_lookup() to take this new object.
This patch restores the block sharing feature.
Fixes: da3eeb904f ("net: flow_offload: add list handling functions")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to annotate the netns on the flow block callback object,
flow_block_cb_is_busy() already checks for used blocks.
Fixes: d63db30c85 ("net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for enabling or disabling the flooding of
unknown multicast traffic on the CPU ports, depending on the value
of the switchdev SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute.
The current behavior is kept unchanged but a user can now prevent
the CPU conduit to be flooded with a lot of unregistered traffic that
the network stack needs to filter in software with e.g.:
echo 0 > /sys/class/net/br0/multicast_router
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a function to check if flow block callback is already in
use. Call this new function from flow_block_cb_setup_simple() and from
drivers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.
This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.
Remove tc_block_offload alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_* and
remove temporary tcf_block_binder_type alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND and remove
temporary tc_block_command alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the dsa_slave_switchdev_port_{attr_set,obj}_event functions
in favor of the switchdev_handle_port_{attr_set,obj_add,obj_del}
helpers which recurse into the lower devices of the target interface.
This has the benefit of being aware of the operations made on the
bridge device itself, where orig_dev is the bridge, and dev is the
slave. This can be used later to configure the hardware switches.
Only VLAN and (port) MDB objects not directly targeting the slave
device are unsupported at the moment, so skip this case in their
respective case statements.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev handle helpers make use of a device checking helper
requiring a const net_device. Make dsa_slave_dev_check compliant
to this.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For drivers that use deferred_xmit for PTP frames (such as sja1105),
there is no need to perform matching between PTP frames and their egress
timestamps, since the sending process can be serialized.
In that case, it makes sense to have the pointer to the skb clone that
DSA made directly in the skb->cb. It will be used for pushing the egress
timestamp back in the application socket's error queue.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
