Pull ARM SoC late updates from Olof Johansson:
"This is some material that we picked up into our tree late, or that
had more complex dependencies on more than one topic branch that makes
sense to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to
better reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: OMAP2+: Drop legacy platform data for omap4 des
ARM: OMAP2+: Drop legacy platform data for omap4 sham
ARM: OMAP2+: Drop legacy platform data for omap4 aes
...
Pull timer updates from Thomas Gleixner:
"The timekeeping and timers departement provides:
- Time namespace support:
If a container migrates from one host to another then it expects
that clocks based on MONOTONIC and BOOTTIME are not subject to
disruption. Due to different boot time and non-suspended runtime
these clocks can differ significantly on two hosts, in the worst
case time goes backwards which is a violation of the POSIX
requirements.
The time namespace addresses this problem. It allows to set offsets
for clock MONOTONIC and BOOTTIME once after creation and before
tasks are associated with the namespace. These offsets are taken
into account by timers and timekeeping including the VDSO.
Offsets for wall clock based clocks (REALTIME/TAI) are not provided
by this mechanism. While in theory possible, the overhead and code
complexity would be immense and not justified by the esoteric
potential use cases which were discussed at Plumbers '18.
The overhead for tasks in the root namespace (ie where host time
offsets = 0) is in the noise and great effort was made to ensure
that especially in the VDSO. If time namespace is disabled in the
kernel configuration the code is compiled out.
Kudos to Andrei Vagin and Dmitry Sofanov who implemented this
feature and kept on for more than a year addressing review
comments, finding better solutions. A pleasant experience.
- Overhaul of the alarmtimer device dependency handling to ensure
that the init/suspend/resume ordering is correct.
- A new clocksource/event driver for Microchip PIT64
- Suspend/resume support for the Hyper-V clocksource
- The usual pile of fixes, updates and improvements mostly in the
driver code"
* tag 'timers-core-2020-01-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
alarmtimer: Make alarmtimer_get_rtcdev() a stub when CONFIG_RTC_CLASS=n
alarmtimer: Use wakeup source from alarmtimer platform device
alarmtimer: Make alarmtimer platform device child of RTC device
alarmtimer: Update alarmtimer_get_rtcdev() docs to reflect reality
hrtimer: Add missing sparse annotation for __run_timer()
lib/vdso: Only read hrtimer_res when needed in __cvdso_clock_getres()
MIPS: vdso: Define BUILD_VDSO32 when building a 32bit kernel
clocksource/drivers/hyper-v: Set TSC clocksource as default w/ InvariantTSC
clocksource/drivers/hyper-v: Untangle stimers and timesync from clocksources
clocksource/drivers/timer-microchip-pit64b: Fix sparse warning
clocksource/drivers/exynos_mct: Rename Exynos to lowercase
clocksource/drivers/timer-ti-dm: Fix uninitialized pointer access
clocksource/drivers/timer-ti-dm: Switch to platform_get_irq
clocksource/drivers/timer-ti-dm: Convert to devm_platform_ioremap_resource
clocksource/drivers/em_sti: Fix variable declaration in em_sti_probe
clocksource/drivers/em_sti: Convert to devm_platform_ioremap_resource
clocksource/drivers/bcm2835_timer: Fix memory leak of timer
clocksource/drivers/cadence-ttc: Use ttc driver as platform driver
clocksource/drivers/timer-microchip-pit64b: Add Microchip PIT64B support
clocksource/drivers/hyper-v: Reserve PAGE_SIZE space for tsc page
...
Change the Hyper-V clocksource ratings to 250, below the TSC clocksource
rating of 300. In configurations where Hyper-V offers an InvariantTSC,
the TSC is not marked "unstable", so the TSC clocksource is available
and preferred. With the higher rating, it will be the default. On
older hardware and Hyper-V versions, the TSC is marked "unstable", so no
TSC clocksource is created and the selected Hyper-V clocksource will be
the default.
Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200109160650.16150-3-parri.andrea@gmail.com
hyperv_timer.c exports hyperv_cs, which is used by stimers and the
timesync mechanism. However, the clocksource dependency is not
needed: these mechanisms only depend on the partition reference
counter (which can be read via a MSR or via the TSC Reference Page).
Introduce the (function) pointer hv_read_reference_counter, as an
embodiment of the partition reference counter read, and export it
in place of the hyperv_cs pointer. The latter can be removed.
This should clarify that there's no relationship between Hyper-V
stimers & timesync and the Linux clocksource abstractions. No
functional or semantic change.
Suggested-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200109160650.16150-2-parri.andrea@gmail.com
Fix up inconsistent usage of upper and lowercase letters in "Exynos"
name.
"EXYNOS" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200104152107.11407-12-krzk@kernel.org
Clean-up commit 8c82723414d5 ("clocksource/drivers/timer-ti-dm: Switch to
platform_get_irq") caused a regression where we now try to access
uninitialized data for timer:
drivers/clocksource/timer-ti-dm.c: In function 'omap_dm_timer_probe':
drivers/clocksource/timer-ti-dm.c:798:13: warning: 'timer' may be used
uninitialized in this function [-Wmaybe-uninitialized]
On boot we now get:
Unable to handle kernel NULL pointer dereference at virtual address
00000004
...
(omap_dm_timer_probe) from [<c061ac7c>] (platform_drv_probe+0x48/0x98)
(platform_drv_probe) from [<c0618c04>] (really_probe+0x1dc/0x348)
(really_probe) from [<c0618ef4>] (driver_probe_device+0x5c/0x160)
Let's fix the issue by moving platform_get_irq to happen after timer has
been allocated.
Fixes: bc83caddf1 ("clocksource/drivers/timer-ti-dm: Switch to platform_get_irq")
Cc: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200106203700.21009-1-tony@atomide.com
Currently when setup_irq fails the error exit path will leak the
recently allocated timer structure. Originally the code would
throw a panic but a later commit changed the behaviour to return
via the err_iounmap path and hence we now have a memory leak. Fix
this by adding a err_timer_free error path that kfree's timer.
Addresses-Coverity: ("Resource Leak")
Fixes: 524a7f0898 ("clocksource/drivers/bcm2835_timer: Convert init function to return error")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191219213246.34437-1-colin.king@canonical.com
Add driver for Microchip PIT64B timer. Timer could be used in continuous
mode or oneshot mode. The hardware has 2x32 bit registers for period
emulating a 64 bit timer. The LSB_PR and MSB_PR registers are used to
set the period value (compare value). TLSB and TMSB keeps the current
value of the counter. After a compare the TLSB and TMSB register resets.
The driver uses PIT64B timer for clocksource or clockevent. First
requested timer would be registered as clockevent, second one would be
registered as clocksource. Individual PIT64B hardware resources were
used for clocksource and clockevent to be able to support high resolution
timers with this hardware implementation.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1576235962-30123-3-git-send-email-claudiu.beznea@microchip.com
Currently, the reserved size for a tsc page is 4K, which is enough for
communicating with hypervisor. However, in the case where we want to
export the tsc page to userspace (e.g. for vDSO to read the
clocksource), the tsc page should be at least PAGE_SIZE, otherwise, when
PAGE_SIZE is larger than 4K, extra kernel data will be mapped into
userspace, which means leaking kernel information.
Therefore reserve PAGE_SIZE space for tsc_pg as a preparation for the
vDSO support of ARM64 in the future. Also, while at it, replace all
reference to tsc_pg with hv_get_tsc_page() since it should be the only
interface to access tsc page.
Signed-off-by: Boqun Feng (Microsoft) <boqun.feng@gmail.com>
Cc: linux-hyperv@vger.kernel.org
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191126021723.4710-1-boqun.feng@gmail.com
The DM365 platform has a strange quirk (only present when using ancient
u-boot - mainline u-boot v2013.01 and later works fine) where if we
enable the second half of the timer in periodic mode before we do its
initialization - the time won't start flowing and we can't boot.
When using more recent u-boot, we can enable the timer, then reinitialize
it and all works fine.
To work around this issue only enable clockevents once tim34 is
initialized i.e. move clockevents_config_and_register() below tim34
initialization.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Pull timer updates from Ingo Molnar:
"The main changes in the timer code in this cycle were:
- Clockevent updates:
- timer-of framework cleanups. (Geert Uytterhoeven)
- Use timer-of for the renesas-ostm and the device name to prevent
name collision in case of multiple timers. (Geert Uytterhoeven)
- Check if there is an error after calling of_clk_get in asm9260
(Chuhong Yuan)
- ABI fix: Zero out high order bits of nanoseconds on compat
syscalls. This got broken a year ago, with apparently no side
effects so far.
Since the kernel would use random data otherwise I don't think we'd
have other options but to fix the bug, even if there was a side
effect to applications (Dmitry Safonov)
- Optimize ns_to_timespec64() on 32-bit systems: move away from
div_s64_rem() which can be slow, to div_u64_rem() which is faster
(Arnd Bergmann)
- Annotate KCSAN-reported false positive data races in
hrtimer_is_queued() users by moving timer->state handling over to
the READ_ONCE()/WRITE_ONCE() APIs. This documents these accesses
(Eric Dumazet)
- Misc cleanups and small fixes"
[ I undid the "ABI fix" and updated the comments instead. The reason
there were apparently no side effects is that the fix was a no-op.
The updated comment is to say _why_ it was a no-op. - Linus ]
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Zero the upper 32-bits in __kernel_timespec on 32-bit
time: Rename tsk->real_start_time to ->start_boottime
hrtimer: Remove the comment about not used HRTIMER_SOFTIRQ
time: Fix spelling mistake in comment
time: Optimize ns_to_timespec64()
hrtimer: Annotate lockless access to timer->state
clocksource/drivers/asm9260: Add a check for of_clk_get
clocksource/drivers/renesas-ostm: Use unique device name instead of ostm
clocksource/drivers/renesas-ostm: Convert to timer_of
clocksource/drivers/timer-of: Use unique device name instead of timer
clocksource/drivers/timer-of: Convert last full_name to %pOF
Pull RISC-V updates from Paul Walmsley:
"New features:
- SECCOMP support
- nommu support
- SBI-less system support
- M-Mode support
- TLB flush optimizations
Other improvements:
- Pass the complete RISC-V ISA string supported by the CPU cores to
userspace, rather than redacting parts of it in the kernel
- Add platform DMA IP block data to the HiFive Unleashed board DT
file
- Add Makefile support for BZ2, LZ4, LZMA, LZO kernel image
compression formats, in line with other architectures
Cleanups:
- Remove unnecessary PTE_PARENT_SIZE macro
- Standardize include guard naming across arch/riscv"
* tag 'riscv/for-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (22 commits)
riscv: provide a flat image loader
riscv: add nommu support
riscv: clear the instruction cache and all registers when booting
riscv: read the hart ID from mhartid on boot
riscv: provide native clint access for M-mode
riscv: dts: add support for PDMA device of HiFive Unleashed Rev A00
riscv: add support for MMIO access to the timer registers
riscv: implement remote sfence.i using IPIs
riscv: cleanup the default power off implementation
riscv: poison SBI calls for M-mode
riscv: don't allow selecting SBI based drivers for M-mode
RISC-V: Add multiple compression image format.
riscv: clean up the macro format in each header file
riscv: Use PMD_SIZE to replace PTE_PARENT_SIZE
riscv: abstract out CSR names for supervisor vs machine mode
riscv: separate MMIO functions into their own header file
riscv: enter WFI in default_power_off() if SBI does not shutdown
RISC-V: Issue a tlb page flush if possible
RISC-V: Issue a local tlbflush if possible.
RISC-V: Do not invoke SBI call if cpumask is empty
...
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of
the patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs
apis so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over
time, it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules
and have it "just work" for a variety of platforms (like a distro
kernel). The big problem turned out to be a lack of dependency
information between different areas of DT entries, and the work here
resolves that problem and now allows devices to boot properly, and
quicker than a monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues"
* tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (68 commits)
tracing: Remove unnecessary DEBUG_FS dependency
of: property: Add device link support for interrupt-parent, dmas and -gpio(s)
debugfs: Fix !DEBUG_FS debugfs_create_automount
of: property: Add device link support for "iommu-map"
of: property: Fix the semantics of of_is_ancestor_of()
i2c: of: Populate fwnode in of_i2c_get_board_info()
drivers: base: Fix Kconfig indentation
firmware_loader: Fix labels with comma for builtin firmware
driver core: Allow device link operations inside sync_state()
driver core: platform: Declare ret variable only once
cpu-topology: declare parse_acpi_topology in <linux/arch_topology.h>
crypto: hisilicon: no need to check return value of debugfs_create functions
driver core: platform: use the correct callback type for bus_find_device
firmware_class: make firmware caching configurable
driver core: Clarify documentation for fwnode_operations.add_links()
mailbox: tegra: Fix superfluous IRQ error message
net: caif: Fix debugfs on 64-bit platforms
mac80211: Use debugfs_create_xul() helper
media: c8sectpfe: no need to check return value of debugfs_create functions
of: property: Add device link support for iommus, mboxes and io-channels
...
Pull x86 hyperv updates from Ingo Molnar:
"Misc updates to the hyperv guest code:
- Rework clockevents initialization to better support hibernation
- Allow guests to enable InvariantTSC
- Micro-optimize send_ipi_one"
* 'x86-hyperv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hyperv: Initialize clockevents earlier in CPU onlining
x86/hyperv: Allow guests to enable InvariantTSC
x86/hyperv: Micro-optimize send_ipi_one()
