It no longer translates to "real irqs" (aka. INO buckets)
so reflect that by using a simpler name for it.
Signed-off-by: David S. Miller <davem@davemloft.net>
All the users go through virt_irq_to_bucket() and essentially
want to go from a virt_irq to an INO, but we have a way
to do that already via virt_to_real_irq_table[].dev_ino.
This also allows us to kill both virt_to_real_irq() and
virt_irq_to_bucket().
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a place to stick INO information in the
virt_to_real_irq_table[], which is currently only used for VIRQs.
And that is readily accessible from the one __irq_ino() call site.
Signed-off-by: David S. Miller <davem@davemloft.net>
We were simply concatenating the devhandle and devino and using that
as the cookie, which defeats the entire purpose of the VIRQ hypervisor
interfaces.
Now that we use physical addresses for the INO buckets, we can
allocate them dynamically for VIRQs and encode the cookies as
~__pa(bucket). This allows us to test for and decode the cookie with
a simple:
brlz $reg1, 1f
xnor $reg1, %g0, $reg2
sequence.
This works because bit 64 is never set in traditional
INO vectors, and it is also never set in a physical
address. So xnor'ing the physical address of the bucket
always gives us a negative number, and thus a unique
condition we can test cheaply.
Inspired by ideas from Greg Onufer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we chain IVEC entries using 32-bit "pointers"
because we know that the ivector_table is in the main
kernel image, thus below 4GB.
This uses proper 64-bit pointers instead.
Whilst this bloats up the kernel image size, this sets
the infrastructure necessary to significantly shrink the
kernel size by using physical addresses and dynamically
allocating the ivector table.
Signed-off-by: David S. Miller <davem@davemloft.net>
This also makes us use the MSI queues correctly.
Each MSI queue is serviced by a normal sun4u/sun4v INO interrupt
handler. This handler runs the MSI queue and dispatches the
virtual interrupts indicated by arriving MSIs in that MSI queue.
All of the common logic is placed in pci_msi.c, with callbacks to
handle the PCI controller specific aspects of the operations.
This common infrastructure will make it much easier to add MSG
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer initialise the name field of the of_platform_driver, but
use the name field of the embedded device_driver's name field instead.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to Tom Callaway for the excellent bug report and
test case.
sys_ipc() has several problems, most to due with semaphore
call handling:
1) 'err' return should be a 'long'
2) "union semun" is passed in a register on 64-bit compared
to 32-bit which provides it on the stack and therefore
by reference
3) Second and third arguments to SEMCTL are swapped compared
to 32-bit.
Signed-off-by: David S. Miller <davem@davemloft.net>
The name field of of_platform_driver is just copied into the
included device_driver. By not overriding an already initialised
device_driver name, we can convert the drivers over time to stop using
the of_platform_driver name.
Also we were not copying the owner field from of_platform_driver, so do
the same with it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply a consistent format to vmlinux.lds.
The file is now to some degree readable.
In addition move several labels inside the braces
such that they reflect the actual start address of a section.
Without this the label would not reflect if ld added alignment.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The support code is identical to the hypervisor sun4v stuff,
just replacing the hypervisor calls with register reads and
writes in the Fire controller.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Don't take semaphore in cpufreq_quick_get()
[CPUFREQ] Support different families in fid/did to frequency conversion
[CPUFREQ] cpufreq_stats: misc cpuinit section annotations
[CPUFREQ] implement !CONFIG_CPU_FREQ stub for cpufreq_unregister_notifier()
[CPUFREQ] mark hotplug notifier callback as __cpuinit
[CPUFREQ] Only check for transition latency on problematic governors (kconfig fix)
[CPUFREQ] allow ondemand and conservative cpufreq governors to be used as default
[CPUFREQ] move policy's governor initialisation out of low-level drivers into cpufreq core
[CPUFREQ] Longhaul - Add support for PM133 northbridge
[CPUFREQ] x86: use num_online_nodes to get physical cpus numbers for
The PCI-E slot on T1000 connects directly to the Fire PCI chip with no
intervening bridges visible in the OBP tree.
Unfortunately the bus numbering of the device in that slot is
different (2) from the PCI host controller (0), and thus the
pci_bus_{read,write}_config_*() calls don't work out.
Complicating things further the Fire PCI controller has no config
space it responds to either.
For now treat this case specially so that devices in the slot work.
Longer term we need to perhaps cons up a dummy bridge between the Fire
and the PCI-E slot so that the bus hierarchy is complete inside of the
kernel and thus the bus numbering all works out right.
Signed-off-by: David S. Miller <davem@davemloft.net>
We should only use ports underneath "domain-services", other DS ports
in the MDESC aren't for us to use.
Signed-off-by: David S. Miller <davem@davemloft.net>
argv and envp are pointers to u32's in userspace, so don't
try to put_user() a NULL to them.
Aparently gcc-4.2.x now warns about this, and since we use
-Werror for arch/sparc64 code, this breaks the build.
Signed-off-by: David S. Miller <davem@davemloft.net>
If of_get_property() fails, it returns NULL and the 'len'
parameter is undefined. So we need to explicitly set len
to zero in such cases.
Noticed by Al Viro.
Signed-off-by: David S. Miller <davem@davemloft.net>
