Pull RTC updates from Alexandre Belloni:
"Subsystem:
- Add a way for drivers to tell the core the supported alarm range is
smaller than the date range. This is not used yet but will be
useful for the alarmtimers in the next release.
- fix Wvoid-pointer-to-enum-cast warnings
- remove redundant of_match_ptr()
- stop warning for invalid alarms when the alarm is disabled
Drivers:
- isl12022: allow setting the trip level for battery level detection
- pcf2127: add support for PCF2131 and multiple timestamps
- stm32: time precision improvement, many fixes
- twl: NVRAM support"
* tag 'rtc-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (73 commits)
dt-bindings: rtc: ds3231: Remove text binding
rtc: wm8350: remove unnecessary messages
rtc: twl: remove unnecessary messages
rtc: sun6i: remove unnecessary message
rtc: stop warning for invalid alarms when the alarm is disabled
rtc: twl: add NVRAM support
rtc: pcf85363: Allow to wake up system without IRQ
rtc: m48t86: add DT support for m48t86
dt-bindings: rtc: Add ST M48T86
rtc: pcf2127: remove useless check
rtc: rzn1: Report maximum alarm limit to rtc core
rtc: ds1305: Report maximum alarm limit to rtc core
rtc: tps6586x: Report maximum alarm limit to rtc core
rtc: cmos: Report supported alarm limit to rtc infrastructure
rtc: cros-ec: Detect and report supported alarm window size
rtc: Add support for limited alarm timer offsets
rtc: isl1208: Fix incorrect logic in isl1208_set_xtoscb()
MAINTAINERS: remove obsolete pattern in RTC SUBSYSTEM section
rtc: tps65910: Remove redundant dev_warn() and do not check for 0 return after calling platform_get_irq()
rtc: omap: Do not check for 0 return after calling platform_get_irq()
...
The RTC on some older Chromebooks can only handle alarms less than
24 hours in the future. The only way to find out is to try to set
an alarm further in the future. If that fails, assume that the RTC
connected to the EC can only handle less than 24 hours of alarm
window, and report that value to the RTC core.
After that change, it is no longer necessary to limit the alarm time
when setting it. Report any excessive alarms to the caller instead.
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230817225537.4053865-4-linux@roeck-us.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It is not possible for platform_get_irq() to return 0. Use the
return value from platform_get_irq().
And there is no need to call the dev_warn() function directly to print
a custom message when handling an error from platform_get_irq()
function as it is going to display an appropriate error message
in case of a failure.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230803080713.4061782-3-ruanjinjie@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This converts the DS2404 to use GPIO descriptors instead of
hard-coded global GPIO numbers.
The platform data can be deleted because there are no in-tree
users and it only contained GPIO numbers which are now
passed using descriptor tables (or device tree or ACPI).
The driver was rewritten to use a state container for the
device driver state (struct ds2404 *chip) and pass that
around instead of using a global singleton storage for the
GPIO handles.
When declaring GPIO descriptor tables or other hardware
descriptions for the RTC driver, implementers should take care
to flag the RESET line as active low, such as by using the
GPIOD_ACTIVE_LOW flag in the descriptor table.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230807-descriptors-rtc-v1-1-ce0f9187576e@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
After the switch to SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() and a subsequent
fix, stm32_rtc_{suspend,resume}() are unused when CONFIG_PM_SLEEP is not
set because SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() is a no-op in that
configuration:
drivers/rtc/rtc-stm32.c:904:12: error: 'stm32_rtc_resume' defined but not used [-Werror=unused-function]
904 | static int stm32_rtc_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~
drivers/rtc/rtc-stm32.c:894:12: error: 'stm32_rtc_suspend' defined but not used [-Werror=unused-function]
894 | static int stm32_rtc_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
The non-"SET_" version of this macro, NOIRQ_SYSTEM_SLEEP_PM_OPS(), is
designed to handle this situation by only assigning the callbacks when
CONFIG_PM_SLEEP is set while allowing the functions to appear used to
the compiler. Switch to that macro to resolve the warnings. There is no
functional change with this, as SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() is
defined using NOIRQ_SYSTEM_SLEEP_PM_OPS() when CONFIG_PM_SLEEP is set.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230815-rtc-stm32-unused-pm-funcs-v1-1-82eb8e02d903@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
