Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv"
* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
power: supply: Introduce Qualcomm PMIC GLINK power supply
soc: apple: rtkit: Do not copy the reg state structure to the stack
soc: sunxi: SUN20I_PPU should depend on PM
memory: renesas-rpc-if: Remove redundant division of dummy
soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
MAINTAINERS: Update qcom CPR maintainer entry
dt-bindings: firmware: document Qualcomm SM8550 SCM
dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
soc: qcom: socinfo: Add support for new field in revision 17
soc: qcom: smd-rpm: Add IPQ9574 compatible
soc: qcom: pmic_glink: remove redundant calculation of svid
soc: qcom: stats: Populate all subsystem debugfs files
dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
soc: qcom: pmic_glink: Introduce altmode support
...
Pull input updates from Dmitry Torokhov:
- a set of tweaks to iqs269a touch controller driver
- a fix for ads7846 driver to properly handle 7845 chip
- cap11xx driver will support cap1203, cap1293 and cap1298 models
- xpad driver will support 8BitDo Pro 2 Wired Controller
- input drivers have been switched to DEFINE_SIMPLE_DEV_PM_OPS() and
pm_sleep_ptr()
- other miscellaneous fixes and tweaks
* tag 'input-for-v6.3-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (113 commits)
dt-bindings: input: iqs626a: Redefine trackpad property types
Input: iqs626a - drop unused device node references
dt-bindings: input: touchscreen: st,stmfts: convert to dtschema
Input: cyttsp5 - fix bitmask for touch buttons
Input: exc3000 - properly stop timer on shutdown
Input: synaptics-rmi4 - fix SPI device ID
Input: cap11xx - add support for cap1203, cap1293 and cap1298
dt-bindings: input: microchip,cap11xx: add cap1203, cap1293 and cap1298
Input: pmic8xxx-keypad - fix a Kconfig spelling mistake & hyphenation
Input: edt-ft5x06 - fix typo in a comment
Input: tegra-kbc - use devm_platform_get_and_ioremap_resource()
Input: st-keyscan - use devm_platform_get_and_ioremap_resource()
Input: spear-keyboard - use devm_platform_get_and_ioremap_resource()
Input: olpc_apsp - use devm_platform_get_and_ioremap_resource()
Input: arc_ps2 - use devm_platform_get_and_ioremap_resource()
Input: apbps2 - use devm_platform_get_and_ioremap_resource()
Input: altera_ps2 - use devm_platform_get_and_ioremap_resource()
Input: ads7846 - don't check penirq immediately for 7845
Input: ads7846 - always set last command to PWRDOWN
Input: ads7846 - don't report pressure for ads7845
...
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
Pull hyperv updates from Wei Liu:
- allow Linux to run as the nested root partition for Microsoft
Hypervisor (Jinank Jain and Nuno Das Neves)
- clean up the return type of callback functions (Dawei Li)
* tag 'hyperv-next-signed-20230220' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/hyperv: Fix hv_get/set_register for nested bringup
Drivers: hv: Make remove callback of hyperv driver void returned
Drivers: hv: Enable vmbus driver for nested root partition
x86/hyperv: Add an interface to do nested hypercalls
Drivers: hv: Setup synic registers in case of nested root partition
x86/hyperv: Add support for detecting nested hypervisor
Pull ARM SoC boardfile updates from Arnd Bergmann
"Unused boardfile removal for 6.3
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate
subsystem trees, but the majority is in the same branch, in order to
better handle dependencies between the patches and avoid breaking
bisection.
Unfortunately that leads to merge conflicts against other changes in
the subsystem trees, but they should all be trivial to resolve by
removing the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed.
The only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users"
* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
mmc: omap: drop TPS65010 dependency
ARM: pxa: restore mfp-pxa320.h
usb: ohci-omap: avoid unused-variable warning
ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
ARM: s3c: remove obsolete s3c-cpu-freq header
MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
ARM: remove CONFIG_UNUSED_BOARD_FILES
mfd: remove htc-pasic3 driver
w1: remove ds1wm driver
usb: remove ohci-tmio driver
fbdev: remove w100fb driver
fbdev: remove tmiofb driver
mmc: remove tmio_mmc driver
mfd: remove ucb1400 support
mfd: remove toshiba tmio drivers
rtc: remove v3020 driver
power: remove pda_power supply driver
ASoC: pxa: remove unused board support
pcmcia: remove unused pxa/sa1100 drivers
...
Each call to device/fwnode_get_named_child_node() must be matched
with a call to fwnode_handle_put() once the corresponding node is
no longer in use. This ensures a reference count remains balanced
in the case of dynamic device tree support.
Currently, the driver never calls fwnode_handle_put(); this patch
adds the missing calls. Because fwnode_handle_put() does not take
a const *fwnode_handle, the const qualifier is removed across all
corresponding *fwnode_handle instances.
As part of this change, trackpad channel touch thresholds and ATI
base values are now specified under single trackpad channel child
nodes. This enhancement moves both properties to scalar values as
opposed to arrays, making their types consistent across bindings.
Fixes: f1d2809de9 ("Input: Add support for Azoteq IQS626A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/Y9RQVe/V1Hnw1oly@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Prior to this patch, the bitmask ends up being 0x3, as opposed to 0x1
which likely was the intention. The erroneous bit results in the driver
reporting 2 different button activations in designs with 2 or more
buttons.
To detect which button has been pressed, cyttsp5_btn_attention() uses a
for loop to iterate through the input buffer, while shifting and
applying a bitmask to determine the state for each button.
Unfortunately, when the bitmask is 0x3 and there are multiple buttons,
this procedure falls apart.
Consider a design with 3 buttons. Pressing the third button will result
in a call to cyttsp5_btn_attention() with the input buffer containing
0x4 (binary 0100). In the first iteration of the for loop cur_btn_state
will be:
(0x4 >> 0 * 1) & 0x3 = 0x4 & 0x3 = 0x0
This is correct. However, in the next iteration this happens:
(0x4 >> 1 * 1) & 0x3 = 0x2 & 0x3 = 0x2
Which means that a key event for key 1 is generated, even though it's
not really active. In the third iteration, the loop detects the button
that was actually pressed:
(0x4 >> 2 * 1) & 0x3 = 0x1 & 0x3 = 0x1
This key event is the only one that should have been detected, but it is
accompanied by the preceding key. Ensuring the applied mask is 0x1
solves this problem.
Signed-off-by: Richard Kjerstadius <richard.kjerstadius@teledyne.com>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20230127102903.3317089-1-richard.kjerstadius@teledyne.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
