Add devlink info support for ef100. The information reported is obtained
through the MCDI interface with the specific meaning defined in new
documentation file.
Signed-off-by: Alejandro Lucero <alejandro.lucero-palau@amd.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Saeed Mahameed says:
====================
mlx5-updates-2023-02-10
1) From Roi and Mark: MultiPort eswitch support
MultiPort E-Switch builds on newer hardware's capabilities and introduces
a mode where a single E-Switch is used and all the vports and physical
ports on the NIC are connected to it.
The new mode will allow in the future a decrease in the memory used by the
driver and advanced features that aren't possible today.
This represents a big change in the current E-Switch implantation in mlx5.
Currently, by default, each E-Switch manager manages its E-Switch.
Steering rules in each E-Switch can only forward traffic to the native
physical port associated with that E-Switch. While there are ways to target
non-native physical ports, for example using a bond or via special TC
rules. None of the ways allows a user to configure the driver
to operate by default in such a mode nor can the driver decide
to move to this mode by default as it's user configuration-driven right now.
While MultiPort E-Switch single FDB mode is the preferred mode, older
generations of ConnectX hardware couldn't support this mode so it was never
implemented. Now that there is capable hardware present, start the
transition to having this mode by default.
Introduce a devlink parameter to control MultiPort Eswitch single FDB mode.
This will allow users to select this mode on their system right now
and in the future will allow the driver to move to this mode by default.
2) From Jiri: Improvements and fixes for mlx5 netdev's devlink logic
2.1) Cleanups related to mlx5's devlink port logic
2.2) Move devlink port registration to be done before netdev alloc
2.3) Create auxdev devlink instance in the same ns as parent devlink
2.4) Suspend auxiliary devices only in case of PCI device suspend
* tag 'mlx5-updates-2023-02-10' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Suspend auxiliary devices only in case of PCI device suspend
net/mlx5: Remove "recovery" arg from mlx5_load_one() function
net/mlx5e: Create auxdev devlink instance in the same ns as parent devlink
net/mlx5e: Move devlink port registration to be done before netdev alloc
net/mlx5e: Move dl_port to struct mlx5e_dev
net/mlx5e: Replace usage of mlx5e_devlink_get_dl_port() by netdev->devlink_port
net/mlx5e: Pass mdev to mlx5e_devlink_port_register()
net/mlx5: Remove outdated comment
net/mlx5e: TC, Remove redundant parse_attr argument
net/mlx5e: Use a simpler comparison for uplink rep
net/mlx5: Lag, Add single RDMA device in multiport mode
net/mlx5: Lag, set different uplink vport metadata in multiport eswitch mode
net/mlx5: E-Switch, rename bond update function to be reused
net/mlx5e: TC, Add peer flow in mpesw mode
net/mlx5: Lag, Control MultiPort E-Switch single FDB mode
====================
Link: https://lore.kernel.org/r/20230214221239.159033-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update devlink-health.rst file:
- Add devlink formatted message (fmsg) API documentation.
- Add auto-dump as a condition to do dump once error reported.
- Expand OOB to clarify this acronym.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MultiPort E-Switch builds on newer hardware's capabilities and introduces
a mode where a single E-Switch is used and all the vports and physical
ports on the NIC are connected to it.
The new mode will allow in the future a decrease in the memory used by the
driver and advanced features that aren't possible today.
This represents a big change in the current E-Switch implantation in mlx5.
Currently, by default, each E-Switch manager manages its E-Switch.
Steering rules in each E-Switch can only forward traffic to the native
physical port associated with that E-Switch. While there are ways to target
non-native physical ports, for example using a bond or via special TC
rules. None of the ways allows a user to configure the driver
to operate by default in such a mode nor can the driver decide
to move to this mode by default as it's user configuration-driven right now.
While MultiPort E-Switch single FDB mode is the preferred mode, older
generations of ConnectX hardware couldn't support this mode so it was never
implemented. Now that there is capable hardware present, start the
transition to having this mode by default.
Introduce a devlink parameter to control MultiPort E-Switch single FDB mode.
This will allow users to select this mode on their system right now
and in the future will allow the driver to move to this mode by default.
Example:
$ devlink dev param set pci/0000:00:0b.0 name esw_multiport value 1 \
cmode runtime
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Expose port function commands to enable / disable migratable
capability, this is used to set the port function as migratable.
Live migration is the process of transferring a live virtual machine
from one physical host to another without disrupting its normal
operation.
In order for a VM to be able to perform LM, all the VM components must
be able to perform migration. e.g.: to be migratable.
In order for VF to be migratable, VF must be bound to VFIO driver with
migration support.
When migratable capability is enabled for a function of the port, the
device is making the necessary preparations for the function to be
migratable, which might include disabling features which cannot be
migrated.
Example of LM with migratable function configuration:
Set migratable of the VF's port function.
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 migratable disable
$ devlink port function set pci/0000:06:00.0/2 migratable enable
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 migratable enable
Bind VF to VFIO driver with migration support:
$ echo <pci_id> > /sys/bus/pci/devices/0000:08:00.0/driver/unbind
$ echo mlx5_vfio_pci > /sys/bus/pci/devices/0000:08:00.0/driver_override
$ echo <pci_id> > /sys/bus/pci/devices/0000:08:00.0/driver/bind
Attach VF to the VM.
Start the VM.
Perform LM.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expose port function commands to enable / disable RoCE, this is used to
control the port RoCE device capabilities.
When RoCE is disabled for a function of the port, function cannot create
any RoCE specific resources (e.g GID table).
It also saves system memory utilization. For example disabling RoCE enable a
VF/SF saves 1 Mbytes of system memory per function.
Example of a PCI VF port which supports function configuration:
Set RoCE of the VF's port function.
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 roce enable
$ devlink port function set pci/0000:06:00.0/2 roce disable
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 roce disable
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
devlink port function hw_addr attr documentation is in mlx5 specific
file while there is nothing mlx5 specific about it.
Move it to devlink-port.rst.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .read handler for the NVM and Shadow RAM regions. This
enables user space to read a small chunk of the flash without needing the
overhead of creating a full snapshot.
Update the documentation for ice to detail which regions have direct read
support.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
78ad87da99 ("ice: devlink: add shadow-ram region to snapshot Shadow RAM")
added support for the 'shadow-ram' devlink region, but did not document it
in the ice devlink documentation. Fix this.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To read from a region, user space must currently request a new snapshot of
the region and then read from that snapshot. This can sometimes be overkill
if user space only reads a tiny portion. They first create the snapshot,
then request a read, then destroy the snapshot.
For regions which have a single underlying "contents", it makes sense to
allow supporting direct reading of the region data.
Extend the DEVLINK_CMD_REGION_READ to allow direct reading from a region if
requested via the new DEVLINK_ATTR_REGION_DIRECT. If this attribute is set,
then perform a direct read instead of using a snapshot. Direct read is
mutually exclusive with DEVLINK_ATTR_REGION_SNAPSHOT_ID, and care is taken
to ensure that we reject commands which provide incorrect attributes.
Regions must enable support for direct read by implementing the .read()
callback function. If a region does not support such direct reads, a
suitable extended error message is reported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kernel test robot reported indentation warnings:
Documentation/networking/devlink/devlink-port.rst:220: WARNING: Unexpected indentation.
Documentation/networking/devlink/devlink-port.rst:222: WARNING: Block quote ends without a blank line; unexpected unindent.
These warnings cause lists (arbitration flow for which the warnings blame to
and 3-step subfunction setup) to be rendered inline instead. Also, for the
former list, automatic list numbering is messed up.
Fix these warnings by adding missing blank line padding.
Link: https://lore.kernel.org/linux-doc/202211200926.kfOPiVti-lkp@intel.com/
Fixes: 242dd64375 ("Documentation: Add documentation for new devlink-rate attributes")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide documentation for newly introduced netlink attributes for
devlink-rate: tx_priority and tx_weight.
Mention the possibility to export tree from the driver.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add documentation to a newly added devlink-rate feature. Provide some
examples on how to use the commands, which netlink attributes are
supported and descriptions of the attributes.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add packet traps for 802.1X operation. The "eapol" control trap is used
to trap EAPOL packets and is required for the correct operation of the
control plane. The "locked_port" drop trap can be enabled to gain
visibility into packets that were dropped by the device due to the
locked bridge port check.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-08-24 (ice)
This series contains updates to ice driver only.
Marcin adds support for TC parsing on TTL and ToS fields.
Anatolli adds support for devlink port split command to allow
configuration of various port configurations.
Jake allows for passing and writing an additional NVM write activate
field by expanding current cmd_flag.
Ani makes PHY debug output more readable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
