.dumpit() callback is used for returning same type of data in the loop,
e.g. loop over ports, resources, devices.
However system parameters are general and standalone for whole
subsystem. It means that getting system parameters should be doit
callback.
Fixes: cb7e0e1305 ("RDMA/core: Add interface to read device namespace sharing mode")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add EFA driver ID to the IOCTL interface uapi. This patch also adds
unspecified node/transport type that will be used by EFA (usnic is left
unchanged as it's already part of our ABI).
Signed-off-by: Gal Pressman <galpress@amazon.com>
Reviewed-by: Shiraz Saleem <shiraz.saleem@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch adds support for allocating, deallocating and registering a new
device memory type, STEERING_SW_ICM. This memory can be allocated and
used by a privileged user for direct rule insertion and management of the
device's steering tables.
The type is provided by the user via the dedicated attribute in the
alloc_dm ioctl command.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch intoruduces a new mlx5_ib driver attribute to the DM allocation
method - the DM type.
In order to allow addition of new types in downstream patches this patch
also refactors the allocation, deallocation and registration handlers to
consider the requested type and perform the necessary actions according to
it.
Since not all future device memory types will be such that are mapped to
user memory, the mandatory page index output attribute is modified to be
optional.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Ariel Levkovich says:
====================
The series exposes the ICM address of the receive transport
interface (TIR) of Raw Packet and RSS QPs to the user since they are
required to properly create and insert steering rules that direct flows to
these QPs.
====================
For dependencies this branch is based on mlx5-next from
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
* branch 'mlx5_tir_icm':
IB/mlx5: Expose TIR ICM address to user space
net/mlx5: Introduce new TIR creation core API
net/mlx5: Expose TIR ICM address in command outbox
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch exposes the TIR ICM address of raw packet and RSS
QPs to user space.
In order to pass the new field, the patch extends the mlx5
specific QP creation response structure and fills it with
the icm address returned by the FW command, if available.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Jason Gunthorpe says:
====================
Upon review it turns out there are some long standing problems in BAR
mapping area:
* BAR pages intended for read-only can be switched to writable via mprotect.
* Missing use of rdma_user_mmap_io for the mlx5 clock BAR page.
* Disassociate causes SIGBUS when touching the pages.
* CPU pages are being mapped through to the process via remap_pfn_range
instead of the more appropriate vm_insert_page, causing weird behaviors
during disassociation.
This series adds the missing VM_* flag manipulation, adds faulting a zero
page for disassociation and revises the CPU page mappings to use
vm_insert_page.
====================
For dependencies this branch is based on for-rc from
git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma.git
* branch 'rdma_mmap':
RDMA: Remove rdma_user_mmap_page
RDMA/mlx5: Use get_zeroed_page() for clock_info
RDMA/ucontext: Fix regression with disassociate
RDMA/mlx5: Use rdma_user_map_io for mapping BAR pages
RDMA/mlx5: Do not allow the user to write to the clock page
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Allow this only via mlx5 raw create flow API, legacy verbs are not
supported. To accommodate that, we add a new attribute to matcher creation
to indicate the type of flow table to be used.
MLX5_IB_ATTR_FLOW_MATCHER_FT_TYPE
With this new attribute MLX5_IB_ATTR_FLOW_MATCHER_FLOW_FLAGS is no longer
needed, we keep it for compatibility but at most only a single attribute can
be passed of the two.
When inserting a flow rule to the FDB we require that a DEVX FT is
provided as a destination, no other configuration is allowed.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Provide an option to change the net namespace of a rdma device through a
netlink command. When multiple rdma devices exists in a system, and when
containers are used, this will limit rdma device visibility to a specified
net namespace.
An example command to change net namespace of mlx5_1 device to the
previously created net namespace 'foo' is:
$ ip netns add foo
$ rdma dev set mlx5_1 netns foo
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When scatter to CQE is enabled on a DCT QP it corrupts the mailbox command
since it tried to treat it as as QP create mailbox command instead of a
DCT create command.
The corrupted mailbox command causes userspace to malfunction as the
device doesn't create the QP as expected.
A new mlx5 capability is exposed to user-space which ensures that it will
not enable the feature on DCT without this fix in the kernel.
Fixes: 5d6ff1babe ("IB/mlx5: Support scatter to CQE for DC transport type")
Signed-off-by: Guy Levi <guyle@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add new RDMA_NLDEV_ATTR_DEV_PROTOCOL attribute to give ability for UDEV
rules create IB device stable names based on link type protocol. The
assumption that devices like mlx4 with duality in their link type under
one IB device struct won't be allowed in the future.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Delete structure which is not connected due to removal in commit
cited in Fixes line.
Fixes: a78e8723a5 ("RDMA/cma: Remove CM_ID statistics provided by rdma-cm module")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add netlink command that enables/disables sharing rdma device among
multiple net namespaces.
Using rdma tool,
$rdma sys set netns shared (default mode)
When rdma subsystem netns mode is set to shared mode, rdma devices
will be accessible in all net namespaces.
Using rdma tool,
$rdma sys set netns exclusive
When rdma subsystem netns mode is set to exclusive mode, devices
will be accessible in only one net namespace at any given
point of time.
If there are any net namespaces other than default init_net exists,
while executing this command, it will fail and mode cannot be changed.
To change this mode, netlink command is used instead of sysctl, because
netlink command allows to auto load a module.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add an interface via netlink command to query whether rdma devices are
shared among multiple net namespaces or not. When using RDMAtool, it can
be queried as,
$rdma system show netns
netns shared
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add support for new LINK messages to allow adding and deleting rdma
interfaces. This will be used initially for soft rdma drivers which
instantiate device instances dynamically by the admin specifying a netdev
device to use. The rdma_rxe module will be the first user of these
messages.
The design is modeled after RTNL_NEWLINK/DELLINK: rdma drivers register
with the rdma core if they provide link add/delete functions. Each driver
registers with a unique "type" string, that is used to dispatch messages
coming from user space. A new RDMA_NLDEV_ATTR is defined for the "type"
string. User mode will pass 3 attributes in a NEWLINK message:
RDMA_NLDEV_ATTR_DEV_NAME for the desired rdma device name to be created,
RDMA_NLDEV_ATTR_LINK_TYPE for the "type" of link being added, and
RDMA_NLDEV_ATTR_NDEV_NAME for the net_device interface to use for this
link. The DELLINK message will contain the RDMA_NLDEV_ATTR_DEV_INDEX of
the device to delete.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
PD, MR and QP objects have parents objects: contexts and PDs. The exposed
parent IDs allow to correlate various objects and simplify debug
investigation.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Give to the user space tools unique identifier for PD, MR, CQ and CM_ID
objects, so they can be able to query on them with .doit callbacks.
QP .doit is not supported yet, till all drivers will be updated to provide
their LQPN to be equal to their restrack ID.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Define new option in 'rdma_set_option' to override calculated QP timeout
when requested to provide QP attributes to modify a QP.
At the same time, pack tos_set to be bitfield.
Signed-off-by: Danit Goldberg <danitg@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
User space verbs provider library would need chip context. Changing the
ABI to add chip version details in structure. Furthermore, changing the
kernel driver ucontext allocation code to initialize the abi structure
with appropriate values.
As suggested by community, appended the new fields at the bottom of the
ABI structure and retaining to older fields as those were in the older
versions.
Keeping the ABI version at 1 and adding a new field in the ucontext
response structure to hold the component mask. The user space library
should check pre-defined flags to figure out if a certain feature is
supported on not.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Netlink statistics exported by rdma-cm never had any working user space
component published to the mailing list or to any open source
project. Canvassing various proprietary users, and the original requester,
we find that there are no real users of this interface.
This patch simply removes all occurrences of RDMA CM netlink in favour of
modern nldev implementation, which provides the same information and
accompanied by widely used user space component.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
A soft iwarp driver that uses the host TCP stack via a kernel mode socket
does not need port mapping. In fact, if the port map daemon, iwpmd, is
running, then iwpmd must not try and create/bind a socket to the actual
port for a soft iwarp connection, since the driver already has that socket
bound.
Yet if the soft iwarp driver wants to interoperate with hard iwarp devices
that -are- using port mapping, then the soft iwarp driver's mappings still
need to be maintained and advertised by the iwpm protocol.
This patch enhances the rdma driver<->iwcm interface to allow an iwarp
driver to specify that it does not want port mapping. The iwpm
kernel<->iwpmd interface is also enhanced to pass up this information on
map requests.
Care is taken to interoperate with the current iwpmd version (ABI version
3) and only use the new NL attributes if iwpmd supports ABI version 4.
The ABI version define has also been created in rdma_netlink.h so both
kernel and user code can share it. The iwcm and iwpmd negotiate the ABI
version to use with a new HELLO netlink message.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In order to add new IWPM_NL attributes, the enums for the IWPM commands
attributes are refactored such that a new attribute can be added without
breaking ABI version 3. Instead of sharing nl attribute enums for both
request and response messages, we create separate enums for each IWPM
message request and reply. This allows us to extend any given IWPM
message by adding new attributes for just that message. These new enums
are created, though, in a way to avoid breaking ABI version 3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Currently a packet is marked for loopback only if the source and
destination addresses equals. This is not enough when multiple gids are
present in rxe device's gid table and the traffic is from one gid to
another. Fix it by marking the packet for loopback if the destination MAC
address is equal to the source MAC address.
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Tested-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Linux 5.0-rc5
Needed to merge the include/uapi changes so we have an up to date
single-tree for these files. Patches already posted are also expected to
need this for dependencies.
