The array limits are supposed to be in units of u32 instead of in bytes.
The current code has a potential array overflow.
Fixes: c614475b0e ('ALSA: dice: add a proc file to show device information')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull second set of sound fixes from Takashi Iwai:
"A collection of small fixes in HD-audio quirks and runtime PM, ASoC
rcar, abs8500 and other codecs. Most of commits are for stable
kernels, too"
* tag 'sound-fix2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Set current_headset_type to ALC_HEADSET_TYPE_ENUM (janitorial)
ALSA: hda - Provide missing pin configs for VAIO with ALC260
ALSA: hda - Add headset quirk for Dell Inspiron 3135
ALSA: hda - Fix the headphone jack detection on Sony VAIO TX
ALSA: hda - Fix missing bass speaker on ASUS N550
ALSA: hda - Fix unbalanced runtime PM notification at resume
ASoC: arizona: Set FLL to free-run before disabling
ALSA: hda - A casual Dell Headset quirk
ASoC: rcar: fixup dma_async_issue_pending() timing
ASoC: rcar: off by one in rsnd_scu_set_route()
ASoC: wm5110: Add post SYSCLK register patch for rev D chip
ASoC: ab8500: Revert to using custom I/O functions
ALSA: hda - Also enable mute/micmute LED control for "Lenovo dock" fixup
ALSA: firewire-lib: include sound/asound.h to refer to snd_pcm_format_t
ALSA: hda - Select FW_LOADER from CONFIG_SND_HDA_CODEC_CA0132_DSP
ALSA: hda - Enable mute/mic-mute LEDs for more Thinkpads with Realtek codec
ASoC: rcar: fixup mod access before checking
This commit fix out of specification about the value of FDF field in out packet
with 'no data'. This affects blocking mode.
According to IEC 61883-6, there is two way to generate AMDTP packets include no
data in blocking mode.
Way 1. an empty packet defined in IEC 61883-1
- Size of packet is 2 quadlets.
- The value of FDF is sfc.
- The packet includes only CIP headers
Way 2. a special non-empty packet defined in IEC 61883-6
- Size of packet is following to blocking mode
- The value of FDF is 0xff. This value is 'NO-DATA'. This means 'The receiver'
must ignore all the data in a CIP with this FDF code'.
- The packet includes dummy data.
But current implementation is a combination of them.
- Size of packet is 2 (way 1)
- FDF = 0xff (way 2)
This causes BeBoB chipset cannot sound.
This patch applies Way 1.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'snd_pcm_format_t' is used by amdtp_out_stream_set_pcm_format().
Currently, when just including amdtp.h, compiler cannot find this type because
this type is defined in uapi/sound/asound.h and this header is not included by
amdtp.h.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At the moment, this driver supports only playback, while FFADO supports
(only) full-duplex devices. So, prevent conflicts by not claiming
devices that would be better handled by FFADO.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
While most DICE devices keep TCAT's default category ID of 0x04, Weiss
devices identify themselves with 0x00.
Reported-by: Rolf Anderegg <rolf.anderegg@weiss.ch>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Doing accesses without quadlet alignment is a bad idea because the
firmware's byte-swapping would garble the data; clarify this in the
documentation.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Instead of relying of some control panel application to configure some
fixed sample rate, allow applications to set it automatically.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
In preparation for sample rate selection support, read the stream
parameters that might change when running at different sample rates.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
In preparation for sample rate selection support, ensure that the driver
knows about the device's clock capabilities.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Avoid a lock inversion between dice->mutex and pcm->open_mutex.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Since commit f2b3614cef (Don't check DMA time-out too shortly), we
need no longer to restrict the period length to less than 10 s.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
When a bus reset happens, the enable register is automatically cleared,
so we do not need to clear it manually when stopping the stream.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add a flag to snd_fw_transaction() to allow it to abort when a bus reset
happens. This removes most of the duplicated error handling loops that
were required around calls to the low-level fw_run_transaction().
Also add a flag to suppress error messages; errors are expected when we
attempt to clean up after the device was unplugged.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Change the AMDTP streaming code to handle the non-standard stream format
that DICE devices use at sample rates greater than 96 kHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
