The _CRS ACPI resources table has 2 entries for the host wakeup GPIO,
the first one being a regular GpioIo () resource while the second one
is a GpioInt () resource for the same pin.
The acpi_gpio_mapping table used by vsc-tp.c maps the first Gpio ()
resource to "wakeuphost-gpios" where as the second GpioInt () entry
is mapped to "wakeuphostint-gpios".
Using "wakeuphost" to request the GPIO as was done until now, means
that the gpiolib-acpi code does not know that the GPIO is active-low
as that info is only available in the GpioInt () entry.
Things were still working before due to the following happening:
1. Since the 2 entries point to the same pin they share a struct gpio_desc
2. The SPI core creates the SPI device vsc-tp.c binds to and calls
acpi_dev_gpio_irq_get(). This does use the second entry and sets
FLAG_ACTIVE_LOW in gpio_desc.flags .
3. vsc_tp_probe() requests the "wakeuphost" GPIO and inherits the
active-low flag set by acpi_dev_gpio_irq_get()
But there is a possible scenario where things do not work:
1. - 3. happen as above
4. After requesting the "wakeuphost" GPIO, the "resetfw" GPIO is requested
next, but its USB GPIO controller is not available yet, so this call
returns -EPROBE_DEFER.
5. The gpio_desc for "wakeuphost" is put() and during this the active-low
flag is cleared from gpio_desc.flags .
6. Later on vsc_tp_probe() requests the "wakeuphost" GPIO again, but now it
is not marked active-low.
The difference can also be seen in /sys/kernel/debug/gpio, which contains
the following line for this GPIO:
gpio-535 ( |wakeuphost ) in hi IRQ ACTIVE LOW
If the second scenario is hit the "ACTIVE LOW" at the end disappears and
things do not work.
Fix this by requesting the GPIO through the "wakeuphostint" mapping instead
which provides active-low info without relying on acpi_dev_gpio_irq_get()
pre-populating this info in the gpio_desc.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2316918
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Tested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Fixes: 566f5ca976 ("mei: Add transport driver for IVSC device")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250214212425.84021-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the const qualifier to all the ctl_tables in the tree except for
watchdog_hardlockup_sysctl, memory_allocation_profiling_sysctls,
loadpin_sysctl_table and the ones calling register_net_sysctl (./net,
drivers/inifiniband dirs). These are special cases as they use a
registration function with a non-const qualified ctl_table argument or
modify the arrays before passing them on to the registration function.
Constifying ctl_table structs will prevent the modification of
proc_handler function pointers as the arrays would reside in .rodata.
This is made possible after commit 78eb4ea25c ("sysctl: treewide:
constify the ctl_table argument of proc_handlers") constified all the
proc_handlers.
Created this by running an spatch followed by a sed command:
Spatch:
virtual patch
@
depends on !(file in "net")
disable optional_qualifier
@
identifier table_name != {
watchdog_hardlockup_sysctl,
iwcm_ctl_table,
ucma_ctl_table,
memory_allocation_profiling_sysctls,
loadpin_sysctl_table
};
@@
+ const
struct ctl_table table_name [] = { ... };
sed:
sed --in-place \
-e "s/struct ctl_table .table = &uts_kern/const struct ctl_table *table = \&uts_kern/" \
kernel/utsname_sysctl.c
Reviewed-by: Song Liu <song@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org> # for kernel/trace/
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> # SCSI
Reviewed-by: Darrick J. Wong <djwong@kernel.org> # xfs
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Bill O'Donnell <bodonnel@redhat.com>
Acked-by: Baoquan He <bhe@redhat.com>
Acked-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Acked-by: Anna Schumaker <anna.schumaker@oracle.com>
Signed-off-by: Joel Granados <joel.granados@kernel.org>
Pull Char/Misc/IIO driver updates from Greg KH:
"Here is the "big" set of char/misc/iio and other smaller driver
subsystem updates for 6.14-rc1. Loads of different things in here this
development cycle, highlights are:
- ntsync "driver" to handle Windows locking types enabling Wine to
work much better on many workloads (i.e. games). The driver
framework was in 6.13, but now it's enabled and fully working
properly. Should make many SteamOS users happy. Even comes with
tests!
- Large IIO driver updates and bugfixes
- FPGA driver updates
- Coresight driver updates
- MHI driver updates
- PPS driver updatesa
- const bin_attribute reworking for many drivers
- binder driver updates
- smaller driver updates and fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (311 commits)
ntsync: Fix reference leaks in the remaining create ioctls.
spmi: hisi-spmi-controller: Drop duplicated OF node assignment in spmi_controller_probe()
spmi: Set fwnode for spmi devices
ntsync: fix a file reference leak in drivers/misc/ntsync.c
scripts/tags.sh: Don't tag usages of DECLARE_BITMAP
dt-bindings: interconnect: qcom,msm8998-bwmon: Add SM8750 CPU BWMONs
dt-bindings: interconnect: OSM L3: Document sm8650 OSM L3 compatible
dt-bindings: interconnect: qcom-bwmon: Document QCS615 bwmon compatibles
interconnect: sm8750: Add missing const to static qcom_icc_desc
memstick: core: fix kernel-doc notation
intel_th: core: fix kernel-doc warnings
binder: log transaction code on failure
iio: dac: ad3552r-hs: clear reset status flag
iio: dac: ad3552r-common: fix ad3541/2r ranges
iio: chemical: bme680: Fix uninitialized variable in __bme680_read_raw()
misc: fastrpc: Fix copy buffer page size
misc: fastrpc: Fix registered buffer page address
misc: fastrpc: Deregister device nodes properly in error scenarios
nvmem: core: improve range check for nvmem_cell_write()
nvmem: qcom-spmi-sdam: Set size in struct nvmem_config
...
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Batch sizing of multiple BARs while memory decoding is disabled
instead of disabling/enabling decoding for each BAR individually;
this optimizes virtualized environments where toggling decoding
enable is expensive (Alex Williamson)
- Add host bridge .enable_device() and .disable_device() hooks for
bridges that need to configure things like Requester ID to StreamID
mapping when enabling devices (Frank Li)
- Extend struct pci_ecam_ops with .enable_device() and
.disable_device() hooks so drivers that use pci_host_common_probe()
instead of their own .probe() have a way to set the
.enable_device() callbacks (Marc Zyngier)
- Drop 'No bus range found' message so we don't complain when DTs
don't specify the default 'bus-range = <0x00 0xff>' (Bjorn Helgaas)
- Rename the drivers/pci/of_property.c struct of_pci_range to
of_pci_range_entry to avoid confusion with the global of_pci_range
in include/linux/of_address.h (Bjorn Helgaas)
Driver binding:
- Update resource request API documentation to encourage callers to
supply a driver name when requesting resources (Philipp Stanner)
- Export pci_intx_unmanaged() and pcim_intx() (always managed) so
callers of pci_intx() (which is sometimes managed) can explicitly
choose the one they need (Philipp Stanner)
- Convert drivers from pci_intx() to always-managed pcim_intx() or
never-managed pci_intx_unmanaged(): amd_sfh, ata (ahci, ata_piix,
pata_rdc, sata_sil24, sata_sis, sata_uli, sata_vsc), bnx2x, bna,
ntb, qtnfmac, rtsx, tifm_7xx1, vfio, xen-pciback (Philipp Stanner)
- Remove pci_intx_unmanaged() since pci_intx() is now always
unmanaged and pcim_intx() is always managed (Philipp Stanner)
Error handling:
- Unexport pcie_read_tlp_log() to encourage drivers to use PCI core
logging rather than building their own (Ilpo Järvinen)
- Move TLP Log handling to its own file (Ilpo Järvinen)
- Store number of supported End-End TLP Prefixes always so we can
read the correct number of DWORDs from the TLP Prefix Log (Ilpo
Järvinen)
- Read TLP Prefixes in addition to the Header Log in
pcie_read_tlp_log() (Ilpo Järvinen)
- Add pcie_print_tlp_log() to consolidate printing of TLP Header and
Prefix Log (Ilpo Järvinen)
- Quirk the Intel Raptor Lake-P PIO log size to accommodate vendor
BIOSes that don't configure it correctly (Takashi Iwai)
ASPM:
- Save parent L1 PM Substates config so when we restore it along with
an endpoint's config, the parent info isn't junk (Jian-Hong Pan)
Power management:
- Avoid D3 for Root Ports on TUXEDO Sirius Gen1 with old BIOS because
the system can't wake up from suspend (Werner Sembach)
Endpoint framework:
- Destroy the EPC device in devm_pci_epc_destroy(), which previously
didn't call devres_release() (Zijun Hu)
- Finish virtual EP removal in pci_epf_remove_vepf(), which
previously caused a subsequent pci_epf_add_vepf() to fail with
-EBUSY (Zijun Hu)
- Write BAR_MASK before iATU registers in pci_epc_set_bar() so we
don't depend on the BAR_MASK reset value being larger than the
requested BAR size (Niklas Cassel)
- Prevent changing BAR size/flags in pci_epc_set_bar() to prevent
reads from bypassing the iATU if we reduced the BAR size (Niklas
Cassel)
- Verify address alignment when programming iATU so we don't attempt
to write bits that are read-only because of the BAR size, which
could lead to directing accesses to the wrong address (Niklas
Cassel)
- Implement artpec6 pci_epc_features so we can rely on all drivers
supporting it so we can use it in EPC core code (Niklas Cassel)
- Check for BARs of fixed size to prevent endpoint drivers from
trying to change their size (Niklas Cassel)
- Verify that requested BAR size is a power of two when endpoint
driver sets the BAR (Niklas Cassel)
Endpoint framework tests:
- Clear pci-epf-test dma_chan_rx, not dma_chan_tx, after freeing
dma_chan_rx (Mohamed Khalfella)
- Correct the DMA MEMCPY test so it doesn't fail if the Endpoint
supports both DMA_PRIVATE and DMA_MEMCPY (Manivannan Sadhasivam)
- Add pci-epf-test and pci_endpoint_test support for capabilities
(Niklas Cassel)
- Add Endpoint test for consecutive BARs (Niklas Cassel)
- Remove redundant comparison from Endpoint BAR test because a > 1MB
BAR can always be exactly covered by iterating with a 1MB buffer
(Hans Zhang)
- Move and convert PCI Endpoint tests from tools/pci to Kselftests
(Manivannan Sadhasivam)
Apple PCIe controller driver:
- Convert StreamID mapping configuration from a bus notifier to the
.enable_device() and .disable_device() callbacks (Marc Zyngier)
Freescale i.MX6 PCIe controller driver:
- Add Requester ID to StreamID mapping configuration when enabling
devices (Frank Li)
- Use DWC core suspend/resume functions for imx6 (Frank Li)
- Add suspend/resume support for i.MX8MQ, i.MX8Q, and i.MX95 (Richard
Zhu)
- Add DT compatible string 'fsl,imx8q-pcie-ep' and driver support for
i.MX8Q series (i.MX8QM, i.MX8QXP, and i.MX8DXL) Endpoints (Frank
Li)
- Add DT binding for optional i.MX95 Refclk and driver support to
enable it if the platform hasn't enabled it (Richard Zhu)
- Configure PHY based on controller being in Root Complex or Endpoint
mode (Frank Li)
- Rely on dbi2 and iATU base addresses from DT via
dw_pcie_get_resources() instead of hardcoding them (Richard Zhu)
- Deassert apps_reset in imx_pcie_deassert_core_reset() since it is
asserted in imx_pcie_assert_core_reset() (Richard Zhu)
- Add missing reference clock enable or disable logic for IMX6SX,
IMX7D, IMX8MM (Richard Zhu)
- Remove redundant imx7d_pcie_init_phy() since
imx7d_pcie_enable_ref_clk() does the same thing (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead
of syscon_regmap_lookup_by_phandle() followed by
of_property_read_u32_array() (Krzysztof Kozlowski)
Marvell MVEBU PCIe controller driver:
- Add MODULE_DEVICE_TABLE() to enable module autoloading (Liao Chen)
MediaTek PCIe Gen3 controller driver:
- Use clk_bulk_prepare_enable() instead of separate
clk_bulk_prepare() and clk_bulk_enable() (Lorenzo Bianconi)
- Rearrange reset assert/deassert so they're both done in the
*_power_up() callbacks (Lorenzo Bianconi)
- Document that Airoha EN7581 requires PHY init and power-on before
PHY reset deassert, unlike other MediaTek Gen3 controllers (Lorenzo
Bianconi)
- Move Airoha EN7581 post-reset delay from the en7581 clock .enable()
method to mtk_pcie_en7581_power_up() (Lorenzo Bianconi)
- Sleep instead of delay during Airoha EN7581 power-up, since this is
a non-atomic context (Lorenzo Bianconi)
- Skip PERST# assertion on Airoha EN7581 during probe and
suspend/resume to avoid a hardware defect (Lorenzo Bianconi)
- Enable async probe to reduce system startup time (Douglas Anderson)
Microchip PolarFlare PCIe controller driver:
- Set up the inbound address translation based on whether the
platform allows coherent or non-coherent DMA (Daire McNamara)
- Update DT binding such that platforms are DMA-coherent by default
and must specify 'dma-noncoherent' if needed (Conor Dooley)
Mobiveil PCIe controller driver:
- Convert mobiveil-pcie.txt to YAML and update 'interrupt-names'
and 'reg-names' (Frank Li)
Qualcomm PCIe controller driver:
- Add DT SM8550 and SM8650 optional 'global' interrupt for link
events (Neil Armstrong)
- Add DT 'compatible' strings for IPQ5424 PCIe controller (Manikanta
Mylavarapu)
- If 'global' IRQ is supported for detection of Link Up events, tell
DWC core not to wait for link up (Krishna chaitanya chundru)
Renesas R-Car PCIe controller driver:
- Avoid passing stack buffer as resource name (King Dix)
Rockchip PCIe controller driver:
- Simplify clock and reset handling by using bulk interfaces (Anand
Moon)
- Pass typed rockchip_pcie (not void) pointer to
rockchip_pcie_disable_clocks() (Anand Moon)
- Return -ENOMEM, not success, when pci_epc_mem_alloc_addr() fails
(Dan Carpenter)
Rockchip DesignWare PCIe controller driver:
- Use dll_link_up IRQ to detect Link Up and enumerate devices so
users don't have to manually rescan (Niklas Cassel)
- Tell DWC core not to wait for link up since the 'sys' interrupt is
required and detects Link Up events (Niklas Cassel)
Synopsys DesignWare PCIe controller driver:
- Don't wait for link up in DWC core if driver can detect Link Up
event (Krishna chaitanya chundru)
- Update ICC and OPP votes after Link Up events (Krishna chaitanya
chundru)
- Always stop link in dw_pcie_suspend_noirq(), which is required at
least for i.MX8QM to re-establish link on resume (Richard Zhu)
- Drop racy and unnecessary LTSSM state check before sending
PME_TURN_OFF message in dw_pcie_suspend_noirq() (Richard Zhu)
- Add struct of_pci_range.parent_bus_addr for devices that need their
immediate parent bus address, not the CPU address, e.g., to program
an internal Address Translation Unit (iATU) (Frank Li)
TI DRA7xx PCIe controller driver:
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead of
syscon_regmap_lookup_by_phandle() followed by
of_parse_phandle_with_fixed_args() or of_property_read_u32_index()
(Krzysztof Kozlowski)
Xilinx Versal CPM PCIe controller driver:
- Add DT binding and driver support for Xilinx Versal CPM5
(Thippeswamy Havalige)
MicroSemi Switchtec management driver:
- Add Microchip PCI100X device IDs (Rakesh Babu Saladi)
Miscellaneous:
- Move reset related sysfs code from pci.c to pci-sysfs.c where other
similar code lives (Ilpo Järvinen)
- Simplify reset_method_store() memory management by using __free()
instead of explicit kfree() cleanup (Ilpo Järvinen)
- Constify struct bin_attribute for sysfs, VPD, P2PDMA, and the IBM
ACPI hotplug driver (Thomas Weißschuh)
- Remove redundant PCI_VSEC_HDR and PCI_VSEC_HDR_LEN_SHIFT (Dongdong
Zhang)
- Correct documentation of the 'config_acs=' kernel parameter
(Akihiko Odaki)"
* tag 'pci-v6.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (111 commits)
PCI: Batch BAR sizing operations
dt-bindings: PCI: microchip,pcie-host: Allow dma-noncoherent
PCI: microchip: Set inbound address translation for coherent or non-coherent mode
Documentation: Fix pci=config_acs= example
PCI: Remove redundant PCI_VSEC_HDR and PCI_VSEC_HDR_LEN_SHIFT
PCI: Don't include 'pm_wakeup.h' directly
selftests: pci_endpoint: Migrate to Kselftest framework
selftests: Move PCI Endpoint tests from tools/pci to Kselftests
misc: pci_endpoint_test: Fix IOCTL return value
dt-bindings: PCI: qcom: Document the IPQ5424 PCIe controller
dt-bindings: PCI: qcom,pcie-sm8550: Document 'global' interrupt
dt-bindings: PCI: mobiveil: Convert mobiveil-pcie.txt to YAML
PCI: switchtec: Add Microchip PCI100X device IDs
misc: pci_endpoint_test: Remove redundant 'remainder' test
misc: pci_endpoint_test: Add consecutive BAR test
misc: pci_endpoint_test: Add support for capabilities
PCI: endpoint: pci-epf-test: Add support for capabilities
PCI: endpoint: pci-epf-test: Fix check for DMA MEMCPY test
PCI: endpoint: pci-epf-test: Set dma_chan_rx pointer to NULL on error
PCI: dwc: Simplify config resource lookup
...
Add a more advanced BAR test that writes all BARs in one go, and then reads
them back and verifies that the value matches the BAR number bitwise OR'ed
with offset, this allows us to verify:
- The BAR number was what we intended to read
- The offset was what we intended to read
This allows us to detect potential address translation issues on the EP.
Reading back the BAR directly after writing will not allow us to detect the
case where inbound address translation on the endpoint incorrectly causes
multiple BARs to be redirected to the same memory region (within the EP).
Link: https://lore.kernel.org/r/20241116032045.2574168-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The test BAR is on the EP side is allocated using pci_epf_alloc_space(),
which allocates the backing memory using dma_alloc_coherent(), which will
return zeroed memory regardless of __GFP_ZERO was set or not.
This means that running a new version of pci-endpoint-test.c (host side)
with an old version of pci-epf-test.c (EP side) will not see any
capabilities being set (as intended), so this is backwards compatible.
Additionally, the EP side always allocates at least 128 bytes for the test
BAR (excluding the MSI-X table), this means that adding another register at
offset 0x30 is still within the 128 available bytes.
For now, we only add the CAP_UNALIGNED_ACCESS capability.
If CAP_UNALIGNED_ACCESS is set, that means that the EP side supports
reading/writing to an address without any alignment requirements.
Thus, if CAP_UNALIGNED_ACCESS is set, make sure that the host side does
not add any extra padding to the buffers that we allocate (which was only
done in order to get the buffers to satisfy certain alignment requirements
by the endpoint controller).
Link: https://lore.kernel.org/r/20241203063851.695733-6-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Pull powerpc updates from Madhavan Srinivasan:
- Add preempt lazy support
- Deprecate cxl and cxl flash driver
- Fix a possible IOMMU related OOPS at boot on pSeries
- Optimize sched_clock() in ppc32 by replacing mulhdu() by
mul_u64_u64_shr()
Thanks to Andrew Donnellan, Andy Shevchenko, Ankur Arora, Christophe
Leroy, Frederic Barrat, Gaurav Batra, Luis Felipe Hernandez, Michael
Ellerman, Nilay Shroff, Ricardo B. Marliere, Ritesh Harjani (IBM),
Sebastian Andrzej Siewior, Shrikanth Hegde, Sourabh Jain, Thorsten Blum,
and Zhu Jun.
* tag 'powerpc-6.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix argument order to timer_sub()
powerpc/prom_init: Use IS_ENABLED()
powerpc/pseries/iommu: IOMMU incorrectly marks MMIO range in DDW
powerpc: Use str_on_off() helper in check_cache_coherency()
powerpc: Large user copy aware of full:rt:lazy preemption
powerpc: Add preempt lazy support
powerpc/book3s64/hugetlb: Fix disabling hugetlb when fadump is active
powerpc/vdso: Mark the vDSO code read-only after init
powerpc/64: Use get_user() in start_thread()
macintosh: declare ctl_table as const
selftest/powerpc/ptrace: Cleanup duplicate macro definitions
selftest/powerpc/ptrace/ptrace-pkey: Remove duplicate macros
selftest/powerpc/ptrace/core-pkey: Remove duplicate macros
powerpc/8xx: Drop legacy-of-mm-gpiochip.h header
scsi/cxlflash: Deprecate driver
cxl: Deprecate driver
selftests/powerpc: Fix typo in test-vphn.c
powerpc/xmon: Use str_yes_no() helper in dump_one_paca()
powerpc/32: Replace mulhdu() by mul_u64_u64_shr()
When ntsync_obj_get_fd() fails, we free the ntsync object but forget to drop the
"file" member.
This was fixed for semaphores in 0e7d523b5f, but
that commit did not fix the similar leak for events and mutexes, since they were
part of patches not yet in the mainline kernel. Fix those cases.
Fixes: 5bc2479a35 "ntsync: Introduce NTSYNC_IOC_CREATE_MUTEX."
Fixes: 4c7404b9c2 "ntsync: Introduce NTSYNC_IOC_CREATE_EVENT."
Signed-off-by: Elizabeth Figura <zfigura@codeweavers.com>
Link: https://lore.kernel.org/r/20250116190717.8923-1-zfigura@codeweavers.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct ntsync_obj contains a reference to struct file
and that reference contributes to refcount - ntsync_alloc_obj()
grabs it. Normally the object is destroyed (and reference
to obj->file dropped) in ntsync_obj_release(). However, in
case of ntsync_obj_get_fd() failure the object is destroyed
directly by its creator.
That case should also drop obj->file; plain kfree(obj)
is not enough there - it ends up leaking struct file * reference.
Take that logics into a helper (ntsync_free_obj()) and
use it in both codepaths that destroy ntsync_obj instances.
Fixes: b46271ec40 "ntsync: Introduce NTSYNC_IOC_CREATE_SEM"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Elizabeth Figura <zfigura@codeweavers.com>
Link: https://lore.kernel.org/r/20250115025002.GA1977892@ZenIV
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the IIO fixes in here as well, and it resolves a merge conflict
in:
drivers/iio/adc/ti-ads1119.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For non-registered buffer, fastrpc driver copies the buffer and
pass it to the remote subsystem. There is a problem with current
implementation of page size calculation which is not considering
the offset in the calculation. This might lead to passing of
improper and out-of-bounds page size which could result in
memory issue. Calculate page start and page end using the offset
adjusted address instead of absolute address.
Fixes: 02b45b47fb ("misc: fastrpc: fix remote page size calculation")
Cc: stable@kernel.org
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20250110134239.123603-4-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For registered buffers, fastrpc driver sends the buffer information
to remote subsystem. There is a problem with current implementation
where the page address is being sent with an offset leading to
improper buffer address on DSP. This is leads to functional failures
as DSP expects base address in page information and extracts offset
information from remote arguments. Mask the offset and pass the base
page address to DSP.
This issue is observed is a corner case when some buffer which is registered
with fastrpc framework is passed with some offset by user and then the DSP
implementation tried to read the data. As DSP expects base address and takes
care of offsetting with remote arguments, passing an offsetted address will
result in some unexpected data read in DSP.
All generic usecases usually pass the buffer as it is hence is problem is
not usually observed. If someone tries to pass offsetted buffer and then
tries to compare data at HLOS and DSP end, then the ambiguity will be observed.
Fixes: 80f3afd72b ("misc: fastrpc: consider address offset before sending to DSP")
Cc: stable@kernel.org
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20250110134239.123603-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory intensive applications(which requires more tha 4GB) that wants
to offload tasks to DSP might have to split the tasks to multiple
user PD to make the resources available.
For every call to DSP, fastrpc driver passes the process tgid which
works as an identifier for the DSP to enqueue the tasks to specific PD.
With current design, if any process opens device node more than once
and makes PD init request, same tgid will be passed to DSP which will
be considered a bad request and this will result in failure as the same
identifier cannot be used for multiple DSP PD.
Assign and pass a client ID to DSP which would be assigned during device
open and will be dependent on the index of session allocated for the PD.
This will allow the same process to open the device more than once and
spawn multiple dynamic PD for ease of processing.
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20250110134308.123739-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unloading the cp500 module leads to the following warning:
kernfs: can not remove 'eeprom', no directory
WARNING: CPU: 1 PID: 1610 at fs/kernfs/dir.c:1683 kernfs_remove_by_name_ns+0xb1/0xc0
The parent I2C device of the nvmem devices is freed before the nvmem
devices. The reference to the nvmem devices is put by devm after
cp500_remove(), but at this time the parent I2C device does not exist
anymore as the I2C controller and its devices have already been freed in
cp500_remove(). Thus, nvmem tries to remove an entry from an already
deleted directory.
Free nvmem devices before I2C controller auxiliary device.
Signed-off-by: Gerhard Engleder <eg@keba.com>
Link: https://lore.kernel.org/r/20241214215759.60811-1-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers should depend on configurations that can be user-configurable
instead of selecting them.
Without this patch, OF cannot be disabled this way:
make allyesconfig
scripts/config -d OF
make olddefconfig
Which is a typical test in CI systems like media-ci.
Now that we are at it, remove the dependency on OF, it will come
automatically from OF_OVERLAY.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20241129-lan966x-depend-v2-1-72bb9397f421@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
