The MCU controls the power-button and beeper, so expose them as input
device. There is of course no interrupt line, so the status of the
power-button needs to be polled. To generate an event the power-button
also needs to be held for 1-2 seconds, so the polling interval does
not need to be overly fast.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20241107114712.538976-7-heiko@sntech.de
Signed-off-by: Lee Jones <lee@kernel.org>
The ON/OFF logic inside the BBNSM allows for connecting directly
into a PMIC or other voltage regulator device. The module has an
button input signal and a wakeup request input signal. It also
has two interrupts (set_pwr_off_irq and set_pwr_on_irq) and an
active-low PMIC enable (pmic_en_b) output.
Add the power key support for the ON/OFF button function found in
BBNSM module.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20230215024117.3357341-2-ping.bai@nxp.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- three new touchscreen drivers: Hycon HY46XX, ILITEK Lego Series,
and MStar MSG2638
- a new driver for Azoteq IQS626A proximity and touch controller
- addition of Amazon Game Controller to the list of devices handled
by the xpad driver
- Elan touchscreen driver will avoid binding to devices described as
I2CHID compatible in ACPI tables
- various driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (56 commits)
Input: xpad - add support for Amazon Game Controller
Input: ili210x - add missing negation for touch indication on ili210x
MAINTAINERS: repair reference in HYCON HY46XX TOUCHSCREEN SUPPORT
Input: add driver for the Hycon HY46XX touchpanel series
dt-bindings: touchscreen: Add HY46XX bindings
dt-bindings: Add Hycon Technology vendor prefix
Input: cyttsp - flag the device properly
Input: cyttsp - set abs params for ABS_MT_TOUCH_MAJOR
Input: cyttsp - drop the phys path
Input: cyttsp - reduce reset pulse timings
Input: cyttsp - error message on boot mode exit error
Input: apbps2 - remove useless variable
Input: mms114 - support MMS136
Input: mms114 - convert bindings to YAML and extend
Input: Add support for ILITEK Lego Series
dt-bindings: input: touchscreen: ilitek_ts_i2c: Add bindings
Input: add MStar MSG2638 touchscreen driver
dt-bindings: input/touchscreen: add bindings for msg2638
Input: silead - add workaround for x86 BIOS-es which bring the chip up in a stuck state
Input: elants_i2c - do not bind to i2c-hid compatible ACPI instantiated devices
...
The Actions Semi ATC260x PMICs are able to manage an onkey button.
This driver exposes the ATC260x onkey as an input device. It can also
be configured to force a system reset on a long key-press with an
adjustable duration.
The currently supported chip variants are ATC2603C and ATC2609A.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds support for the power button attached to the Embedded Controller
on a Dell Wyse 3020 "Ariel" board.
The Embedded Controller's SPI interface is actually capable sending and
receiving the PS/2 keyboard and mouse protocol data, which looks like
a good fit for a serio driver. Howerver, I don't know of any machines where
this is actually used.
My board only has a single power button and no way to connect an actual
keyboard or a mouse. Using the atkbd driver with serio would be an overkill
and would be inconvenient for the userspace. Therefore this driver
registers an input device that is only capable of reporting the power
button presses and releases.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20201201083533.1724287-3-lkundrak@v3.sk
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Provide a simple driver for GPIO controllable vibrators.
It will be used by the Fairphone 2.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- update the ili210x touchscreen driver, refreshing the code and adding
support for ILI251X line
- add support for st1633 to the st1232 touchscreen driver
- add support for sx8650 to the the sx8654 touchscreen driver
- add support for Evervision FT5726 to the edt-ft5x06 touchscreen
driver
- add support for gt5688 to the Goodix touchscreen driver
- new vibrator driver for MSM SOCs
- miscellaneous fixes for the rest of input drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (53 commits)
Input: wacom_serial4 - add support for Wacom ArtPad II tablet
Input: elan_i2c - add id for touchpad found in Lenovo s21e-20
Input: raspberrypi-ts - select CONFIG_INPUT_POLLDEV
Input: msm-vibrator - use correct gpio header
Input: ti_am335x_tsc - remove set but not used variable 'tscadc_dev'
Input: i8042 - rework DT node name comparisons
Input: goodix - print values in case of inconsistencies
Input: goodix - refer to touchscreen.txt in device tree bindings
Input: goodix - support Goodix gt5688
Input: synaptics_i2c - remove redundant spinlock
Input: db9 - mark expected switch fall-through
Input: qt2160 - remove redundant spinlock
Input: st1232 - handle common DT bindings
Input: ims-pcu - switch to using brightness_set_blocking()
Input: st1232 - switch to gpiod API
Input: ili210x - fetch touchscreen geometry from DT
Input: msm-vibrator - tweak an error message
Input: tm2-touchkey - acknowledge that setting brightness is a blocking call
Input: stmfts - acknowledge that setting brightness is a blocking call
Input: ili210x - switch to using devm_device_add_group()
...
