s2idle works like a regular suspend with freezing processes and freezing
devices. All CPUs except the control CPU go into idle. Once this is
completed the control CPU kicks all other CPUs out of idle, so that they
reenter the idle loop and then enter s2idle state. The control CPU then
issues an swait() on the suspend state and therefore enters the idle loop
as well.
Due to being kicked out of idle, the other CPUs leave their NOHZ states,
which means the tick is active and the corresponding hrtimer is programmed
to the next jiffie.
On entering s2idle the CPUs shut down their local clockevent device to
prevent wakeups. The last CPU which enters s2idle shuts down its local
clockevent and freezes timekeeping.
On resume, one of the CPUs receives the wakeup interrupt, unfreezes
timekeeping and its local clockevent and starts the resume process. At that
point all other CPUs are still in s2idle with their clockevents switched
off. They only resume when they are kicked by another CPU or after resuming
devices and then receiving a device interrupt.
That means there is no guarantee that all CPUs will wakeup directly on
resume. As a consequence there is no guarantee that timers which are queued
on those CPUs and should expire directly after resume, are handled. Also
timer list timers which are remotely queued to one of those CPUs after
resume will not result in a reprogramming IPI as the tick is
active. Queueing a hrtimer will also not result in a reprogramming IPI
because the first hrtimer event is already in the past.
The recent introduction of the timer pull model (7ee9887703 ("timers:
Implement the hierarchical pull model")) amplifies this problem, if the
current migrator is one of the non woken up CPUs. When a non pinned timer
list timer is queued and the queuing CPU goes idle, it relies on the still
suspended migrator CPU to expire the timer which will happen by chance.
The problem exists since commit 8d89835b04 ("PM: suspend: Do not pause
cpuidle in the suspend-to-idle path"). There the cpuidle_pause() call which
in turn invoked a wakeup for all idle CPUs was moved to a later point in
the resume process. This might not be reached or reached very late because
it waits on a timer of a still suspended CPU.
Address this by kicking all CPUs out of idle after the control CPU returns
from swait() so that they resume their timers and restore consistent system
state.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218641
Fixes: 8d89835b04 ("PM: suspend: Do not pause cpuidle in the suspend-to-idle path")
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: 5.16+ <stable@kernel.org> # 5.16+
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
psci_init_system_suspend() invokes suspend_set_ops() very early during
bootup even before kernel command line for mem_sleep_default is setup.
This leads to kernel command line mem_sleep_default=s2idle not working
as mem_sleep_current gets changed to deep via suspend_set_ops() and never
changes back to s2idle.
Set mem_sleep_current along with mem_sleep_default during kernel command
line setup as default suspend mode.
Fixes: faf7ec4a92 ("drivers: firmware: psci: add system suspend support")
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Maulik Shah <quic_mkshah@quicinc.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is not necessary to define struct suspend_stats in a header file and the
suspend_stats variable in the core device system-wide PM code. They both
can be defined in kernel/power/main.c, next to the sysfs and debugfs code
accessing suspend_stats, which can be static.
Modify the code in question in accordance with the above observation and
replace the static inline functions manipulating suspend_stats with
regular ones defined in kernel/power/main.c.
While at it, move the enum suspend_stat_step to the end of suspend.h which
is a more suitable place for it.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of using a set of individual struct suspend_stats fields
representing suspend step failure counters, use an array of counters
indexed by enum suspend_stat_step for this purpose, which allows
dpm_save_failed_step() to increment the appropriate counter
automatically, so that its callers don't need to do that directly.
It also allows suspend_stats_show() to carry out a loop over the
counters array to print their values.
Because the counters cannot become negative, use unsigned int for
representing them.
The only user-observable impact of this change is a different
ordering of entries in the suspend_stats debugfs file which is not
expected to matter.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull scheduler updates from Ingo Molnar:
"Debuggability:
- Change most occurances of BUG_ON() to WARN_ON_ONCE()
- Reorganize & fix TASK_ state comparisons, turn it into a bitmap
- Update/fix misc scheduler debugging facilities
Load-balancing & regular scheduling:
- Improve the behavior of the scheduler in presence of lot of
SCHED_IDLE tasks - in particular they should not impact other
scheduling classes.
- Optimize task load tracking, cleanups & fixes
- Clean up & simplify misc load-balancing code
Freezer:
- Rewrite the core freezer to behave better wrt thawing and be
simpler in general, by replacing PF_FROZEN with TASK_FROZEN &
fixing/adjusting all the fallout.
Deadline scheduler:
- Fix the DL capacity-aware code
- Factor out dl_task_is_earliest_deadline() &
replenish_dl_new_period()
- Relax/optimize locking in task_non_contending()
Cleanups:
- Factor out the update_current_exec_runtime() helper
- Various cleanups, simplifications"
* tag 'sched-core-2022-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
sched: Fix more TASK_state comparisons
sched: Fix TASK_state comparisons
sched/fair: Move call to list_last_entry() in detach_tasks
sched/fair: Cleanup loop_max and loop_break
sched/fair: Make sure to try to detach at least one movable task
sched: Show PF_flag holes
freezer,sched: Rewrite core freezer logic
sched: Widen TAKS_state literals
sched/wait: Add wait_event_state()
sched/completion: Add wait_for_completion_state()
sched: Add TASK_ANY for wait_task_inactive()
sched: Change wait_task_inactive()s match_state
freezer,umh: Clean up freezer/initrd interaction
freezer: Have {,un}lock_system_sleep() save/restore flags
sched: Rename task_running() to task_on_cpu()
sched/fair: Cleanup for SIS_PROP
sched/fair: Default to false in test_idle_cores()
sched/fair: Remove useless check in select_idle_core()
sched/fair: Avoid double search on same cpu
sched/fair: Remove redundant check in select_idle_smt()
...
Rafael explained that the reason for having both PF_NOFREEZE and
PF_FREEZER_SKIP is that {,un}lock_system_sleep() is callable from
kthread context that has previously called set_freezable().
In preparation of merging the flags, have {,un}lock_system_slee() save
and restore current->flags.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20220822114648.725003428@infradead.org
The CXL specification claims S3 support at a hardware level, but at a
system software level there are some missing pieces. Section 9.4 (CXL
2.0) rightly claims that "CXL mem adapters may need aux power to retain
memory context across S3", but there is no enumeration mechanism for the
OS to determine if a given adapter has that support. Moreover the save
state and resume image for the system may inadvertantly end up in a CXL
device that needs to be restored before the save state is recoverable.
I.e. a circular dependency that is not resolvable without a third party
save-area.
Arrange for the cxl_mem driver to fail S3 attempts. This still nominaly
allows for suspend, but requires unbinding all CXL memory devices before
the suspend to ensure the typical DRAM flow is taken. The cxl_mem unbind
flow is intended to also tear down all CXL memory regions associated
with a given cxl_memdev.
It is reasonable to assume that any device participating in a System RAM
range published in the EFI memory map is covered by aux power and
save-area outside the device itself. So this restriction can be
minimized in the future once pre-existing region enumeration support
arrives, and perhaps a spec update to clarify if the EFI memory map is
sufficent for determining the range of devices managed by
platform-firmware for S3 support.
Per Rafael, if the CXL configuration prevents suspend then it should
fail early before tasks are frozen, and mem_sleep should stop showing
'mem' as an option [1]. Effectively CXL augments the platform suspend
->valid() op since, for example, the ACPI ops are not aware of the CXL /
PCI dependencies. Given the split role of platform firmware vs OS
provisioned CXL memory it is up to the cxl_mem driver to determine if
the CXL configuration has elements that platform firmware may not be
prepared to restore.
Link: https://lore.kernel.org/r/CAJZ5v0hGVN_=3iU8OLpHY3Ak35T5+JcBM-qs8SbojKrpd0VXsA@mail.gmail.com [1]
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/165066828317.3907920.5690432272182042556.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
After commit e3728b50cd ("ACPI: PM: s2idle: Avoid possible race
related to the EC GPE") wakeup interrupts occurring immediately after
the one discarded by acpi_s2idle_wake() may be missed. Moreover, if
the SCI triggers again immediately after the rearming in
acpi_s2idle_wake(), that wakeup may be missed too.
The problem is that pm_system_irq_wakeup() only calls pm_system_wakeup()
when pm_wakeup_irq is 0, but that's not the case any more after the
interrupt causing acpi_s2idle_wake() to run until pm_wakeup_irq is
cleared by the pm_wakeup_clear() call in s2idle_loop(). However,
there may be wakeup interrupts occurring in that time frame and if
that happens, they will be missed.
To address that issue first move the clearing of pm_wakeup_irq to
the point at which it is known that the interrupt causing
acpi_s2idle_wake() to tun will be discarded, before rearming the SCI
for wakeup. Moreover, because that only reduces the size of the
time window in which the issue may manifest itself, allow
pm_system_irq_wakeup() to register two second wakeup interrupts in
a row and, when discarding the first one, replace it with the second
one. [Of course, this assumes that only one wakeup interrupt can be
discarded in one go, but currently that is the case and I am not
aware of any plans to change that.]
Fixes: e3728b50cd ("ACPI: PM: s2idle: Avoid possible race related to the EC GPE")
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make valid_state() check if the ->enter callback is present in
suspend_ops (only PM_SUSPEND_TO_IDLE can be valid otherwise) and
make sleep_state_supported() call valid_state() consistently to
validate the states other than PM_SUSPEND_TO_IDLE.
While at it, clean up the comment in valid_state().
No expected functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 8651f97bd9 ("PM / cpuidle: System resume hang fix with
cpuidle") that introduced cpuidle pausing during system suspend
did that to work around a platform firmware issue causing systems
to hang during resume if CPUs were allowed to enter idle states
in the system suspend and resume code paths.
However, pausing cpuidle before the last phase of suspending
devices is the source of an otherwise arbitrary difference between
the suspend-to-idle path and other system suspend variants, so it is
cleaner to do that later, before taking secondary CPUs offline (it
is still safer to take secondary CPUs offline with cpuidle paused,
though).
Modify the code accordingly, but in order to avoid code duplication,
introduce new wrapper functions, pm_sleep_disable_secondary_cpus()
and pm_sleep_enable_secondary_cpus(), to combine cpuidle_pause()
and cpuidle_resume(), respectively, with the handling of secondary
CPUs during system-wide transitions to sleep states.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
It is pointless to pause cpuidle in the suspend-to-idle path,
because it is going to be resumed in the same path later and
pausing it does not serve any particular purpose in that case.
Rework the code to avoid doing that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Revert commit bfcc1e67ff ("PM: sleep: Do not assume that "mem" is
always present"), because it breaks compatibility with user space
utilities assuming that "mem" will always be present in
/sys/power/state.
Fixes: bfcc1e67ff ("PM: sleep: Do not assume that "mem" is always present")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
An implementation of suspend_ops is allowed to reject the PM_SUSPEND_MEM
suspend type from its ->valid() callback, we should not assume that it
is always present as this is not a correct reflection of what a firmware
interface may support.
Fixes: 406e79385f ("PM / sleep: System sleep state selection interface rework")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().
Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add parameter explanation to fix kernel-doc marks:
kernel/power/suspend.c:233: warning: Function parameter or member
'state' not described in 'suspend_valid_only_mem'
kernel/power/suspend.c:344: warning: Function parameter or member
'state' not described in 'suspend_prepare'
Signed-off-by: Alex Shi <alex.shi@linux.alibaba.com>
[ rjw: Change the proposed parameter descriptions. ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The current notifiers have the following error handling pattern all
over the place:
int err, nr;
err = __foo_notifier_call_chain(&chain, val_up, v, -1, &nr);
if (err & NOTIFIER_STOP_MASK)
__foo_notifier_call_chain(&chain, val_down, v, nr-1, NULL)
And aside from the endless repetition thereof, it is broken. Consider
blocking notifiers; both calls take and drop the rwsem, this means
that the notifier list can change in between the two calls, making @nr
meaningless.
Fix this by replacing all the __foo_notifier_call_chain() functions
with foo_notifier_call_chain_robust() that embeds the above pattern,
but ensures it is inside a single lock region.
Note: I switched atomic_notifier_call_chain_robust() to use
the spinlock, since RCU cannot provide the guarantee
required for the recovery.
Note: software_resume() error handling was broken afaict.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20200818135804.325626653@infradead.org
It is theoretically possible for the ACPI EC GPE to be set after the
s2idle_ops->wake() called from s2idle_loop() has returned and before
the subsequent pm_wakeup_pending() check is carried out. If that
happens, the resulting wakeup event will cause the system to resume
even though it may be a spurious one.
To avoid that race, first make the ->wake() callback in struct
platform_s2idle_ops return a bool value indicating whether or not
to let the system resume and rearrange s2idle_loop() to use that
value instad of the direct pm_wakeup_pending() call if ->wake() is
present.
Next, rework acpi_s2idle_wake() to process EC events and check
pm_wakeup_pending() before re-arming the SCI for system wakeup
to prevent it from triggering prematurely and add comments to
that function to explain the rationale for the new code flow.
Fixes: 56b9918490 ("PM: sleep: Simplify suspend-to-idle control flow")
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The sysfs attribute `/sys/power/sync_on_suspend` controls, whether or not
filesystems are synced by the kernel before system suspend.
Congruously, the behaviour of build-time switch CONFIG_SUSPEND_SKIP_SYNC
is slightly changed: It now defines the run-tim default for the new sysfs
attribute `/sys/power/sync_on_suspend`.
The run-time attribute is added because the existing corresponding
build-time Kconfig flag for (`CONFIG_SUSPEND_SKIP_SYNC`) is not flexible
enough. E.g. Linux distributions that provide pre-compiled kernels
usually want to stick with the default (sync filesystems before suspend)
but under special conditions this needs to be changed.
One example for such a special condition is user-space handling of
suspending block devices (e.g. using `cryptsetup luksSuspend` or `dmsetup
suspend`) before system suspend. The Kernel trying to sync filesystems
after the underlying block device already got suspended obviously leads
to dead-locks. Be aware that you have to take care of the filesystem sync
yourself before suspending the system in those scenarios.
Signed-off-by: Jonas Meurer <jonas@freesources.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit ac9eafbe93 ("ACPI: PM: s2idle: Execute LPS0 _DSM
functions with suspended devices"), a NULL pointer may be dereferenced
if suspend-to-idle is attempted on a platform without "traditional"
suspend support due to invalid fall-through in
platform_suspend_prepare_noirq().
Fix that and while at it add missing braces in platform_resume_noirq().
Fixes: ac9eafbe93 ("ACPI: PM: s2idle: Execute LPS0 _DSM functions with suspended devices")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
According to Section 3.5 of the "Intel Low Power S0 Idle" document [1],
Function 5 of the LPS0 _DSM is expected to be invoked when the system
configuration matches the criteria for entering the target low-power
state of the platform. In particular, this means that all devices
should be suspended and in low-power states already when that function
is invoked.
This is not the case currently, however, because Function 5 of the
LPS0 _DSM is invoked by it before the "noirq" phase of device suspend,
which means that some devices may not have been put into low-power
states yet at that point. That is a consequence of the previous
design of the suspend-to-idle flow that allowed the "noirq" phase of
device suspend and the "noirq" phase of device resume to be carried
out for multiple times while "suspended" (if any spurious wakeup
events were detected) and the point of the LPS0 _DSM Function 5
invocation was chosen so as to call it (and LPS0 _DSM Function 6
analogously) once per suspend-resume cycle (regardless of how many
times the "noirq" phases of device suspend and resume were carried
out while "suspended").
Now that the suspend-to-idle flow has been redesigned to carry out
the "noirq" phases of device suspend and resume once in each cycle,
the code can be reordered to follow the specification that it is
based on more closely.
For this purpose, add ->prepare_late and ->restore_early platform
callbacks for suspend-to-idle, to be executed, respectively, after
the "noirq" phase of suspending devices and before the "noirq"
phase of resuming them and make ACPI use them for the invocation
of LPS0 _DSM functions as appropriate.
While at it, move the LPS0 entry requirements check to be made
before invoking Functions 3 and 5 of the LPS0 _DSM (also once
per cycle) as follows from the specification [1].
Link: https://uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf # [1]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
After previous changes the suspend-to-idle code flow can be
integrated more tightly with the generic system suspend code flow
by making suspend_enter() call s2idle_loop() later and removing
the direct invocations of dpm_noirq_begin(),
dpm_noirq_suspend_devices(), dpm_noirq_end(), and
dpm_noirq_resume_devices() from the latter, so do that.
This change is not expected to alter functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
After commit 33e4f80ee6 ("ACPI / PM: Ignore spurious SCI wakeups
from suspend-to-idle") the "noirq" phases of device suspend and
resume may run for multiple times during suspend-to-idle, if there
are spurious system wakeup events while suspended. However, this
is complicated and fragile and actually unnecessary.
The main reason for doing this is that on some systems the EC may
signal system wakeup events (power button events, for example) as
well as events that should not cause the system to resume (spurious
system wakeup events). Thus, in order to determine whether or not
a given event signaled by the EC while suspended is a proper system
wakeup one, the EC GPE needs to be dispatched and to start with that
was achieved by allowing the ACPI SCI action handler to run, which
was only possible after calling resume_device_irqs().
However, dispatching the EC GPE this way turned out to take too much
time in some cases and some EC events might be missed due to that, so
commit 68e2201185 ("ACPI: EC: Dispatch the EC GPE directly on
s2idle wake") started to dispatch the EC GPE right after a wakeup
event has been detected, so in fact the full ACPI SCI action handler
doesn't need to run any more to deal with the wakeups coming from the
EC.
Use this observation to simplify the suspend-to-idle control flow
so that the "noirq" phases of device suspend and resume are each
run only once in every suspend-to-idle cycle, which is reported to
significantly reduce power drawn by some systems when suspended to
idle (by allowing them to reach a deep platform-wide low-power state
through the suspend-to-idle flow). [What appears to happen is that
the "noirq" resume of devices after a spurious EC wakeup brings some
devices into a state in which they prevent the platform from reaching
the deep low-power state going forward, even after a subsequent
"noirq" suspend phase, and on some systems the EC triggers such
wakeups already when the "noirq" suspend of devices is running for
the first time in the given suspend/resume cycle, so the platform
cannot reach the deep low-power state at all.]
First, make acpi_s2idle_wake() use the acpi_ec_dispatch_gpe() return
value to determine whether or not the wakeup may have been triggered
by the EC (in which case the system wakeup is canceled and ACPI
events are processed in order to determine whether or not the event
is a proper system wakeup one) and use rearm_wake_irq() (introduced
by a previous change) in it to rearm the ACPI SCI for system wakeup
detection in case the system will remain suspended.
Second, drop acpi_s2idle_sync(), which is not needed any more, and
the corresponding global platform suspend-to-idle callback.
Next, drop the pm_wakeup_pending() check (which is an optimization
only) from __device_suspend_noirq() to prevent it from returning
errors on system wakeups occurring before the "noirq" phase of
device suspend is complete (as in the case of suspend-to-idle it is
not known whether or not these wakeups are suprious at that point),
in order to avoid having to carry out a "noirq" resume of devices
on a spurious system wakeup.
Finally, change the code flow in s2idle_loop() to (1) run the
"noirq" suspend of devices once before starting the loop, (2) check
for spurious EC wakeups (via the platform ->wake callback) for the
first time before calling s2idle_enter(), and (3) run the "noirq"
resume of devices once after leaving the loop.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
* pm-sleep:
PM: sleep: Drop dev_pm_skip_next_resume_phases()
ACPI: PM: Drop unused function and function header
ACPI: PM: Introduce "poweroff" callbacks for ACPI PM domain and LPSS
ACPI: PM: Simplify and fix PM domain hibernation callbacks
PCI: PM: Simplify bus-level hibernation callbacks
PM: ACPI/PCI: Resume all devices during hibernation
kernel: power: swap: use kzalloc() instead of kmalloc() followed by memset()
PM: sleep: Update struct wakeup_source documentation
drivers: base: power: remove wakeup_sources_stats_dentry variable
PM: suspend: Rename pm_suspend_via_s2idle()
PM: sleep: Show how long dpm_suspend_start() and dpm_suspend_end() take
PM: hibernate: powerpc: Expose pfn_is_nosave() prototype
There are platforms that do not call pm_set_suspend_via_firmware(),
so pm_suspend_via_firmware() returns 'false' on them, but the power
states of PCI devices (PCIe ports in particular) are changed as a
result of powering down core platform components during system-wide
suspend. Thus the pm_suspend_via_firmware() checks in
pci_pm_suspend_noirq() and pci_pm_resume_noirq() introduced by
commit 3e26c5feed ("PCI: PM: Skip devices in D0 for suspend-to-
idle") are not sufficient to determine that devices left in D0
during suspend will remain in D0 during resume and so the bus-level
power management can be skipped for them.
For this reason, introduce a new global suspend flag,
PM_SUSPEND_FLAG_NO_PLATFORM, set it for suspend-to-idle only
and replace the pm_suspend_via_firmware() checks mentioned above
with checks against this flag.
Fixes: 3e26c5feed ("PCI: PM: Skip devices in D0 for suspend-to-idle")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
