Pull MMC updates from Ulf Hansson:
"MMC core:
- Share a helper to convert from crypto_profile to mmc_host
- Respect quirk_max_rate for non-UHS SDIO card too
MMC host:
- Add DT bindings for the mmc-slot
- Clarify DT bindings for the mmc-controller
- bcm2835: Add support for system-wide suspend/resume PM
- dw_mmc-exynos: Add support for the exynos8895 variant
- meson-mx-sdio: Convert DT bindings to dtschema
- mtk-sd: Fixup use of two register ranges
- mtk-sd: Add support for ignoring cmd response CRC
- sdhci-esdhc-imx: enable 'SDHCI_QUIRK_NO_LED' quirk for S32G
- sdhci-msm: Correctly set the load for the regulator
- sdhci-msm: Convert to use custom crypto profile
- sdhci-of-at91: Add support for the microchip sama7d65 variant"
* tag 'mmc-v6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (25 commits)
mmc: sdhci-msm: Correctly set the load for the regulator
mmc: hi3798mv200: Use syscon_regmap_lookup_by_phandle_args
mmc: Use of_property_present() for non-boolean properties
dt-bindings: mmc: samsung,exynos-dw-mshc: add specific compatible for exynos8895
mmc: sdhci-msm: convert to use custom crypto profile
mmc: crypto: add mmc_from_crypto_profile()
mmc: mtk-sd: Limit getting top_base to SoCs that require it
dt-bindings: mmc: mtk-sd: Document compatibles that need two register ranges
mmc: sdhci-acpi: Use devm_platform_ioremap_resource()
mmc: sdhci-acpi: Remove not so useful error message
dt-bindings: mmc: convert amlogic,meson-mx-sdio.txt to dtschema
dt-bindings: mmc: document mmc-slot
dt-bindings: mmc: controller: remove '|' when not needed
dt-bindings: mmc: controller: move properties common with slot out to mmc-controller-common
dt-bindings: mmc: controller: clarify the address-cells description
mmc: bcm2835: add suspend/resume pm support
dt-bindings: Drop Bhupesh Sharma from maintainers
mmc: core: don't include 'pm_wakeup.h' directly
mmc: mtk-sd: Add support for ignoring cmd response CRC
mmc: core: Introduce the MMC_RSP_R1B_NO_CRC response
...
BLK_MQ_F_SHOULD_MERGE is set for all tag_sets except those that purely
process passthrough commands (bsg-lib, ufs tmf, various nvme admin
queues) and thus don't even check the flag. Remove it to simplify the
driver interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241219060214.1928848-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support for Ultra Capacity SD cards (SDUC, 2TB to 128TB)
- Add support for Ultra High-Speed II SD cards (UHS-II)
- Use a reset control for pwrseq_simple
- Add SD card quirk for broken poweroff notification
- Use GFP_NOIO for SD ACMD22
MMC host:
- bcm2835: Introduce proper clock handling
- mtk-sd: Add support for the Host-Software-Queue interface
- mtk-sd: Add support for the mt7988/mt8196 variants
- mtk-sd: Fix a couple of error paths in ->probe()
- sdhci: Add interface to support UHS-II SD cards
- sdhci_am654: Fixup support for changing the signal voltage level
- sdhci-cadence: Add support for the Microchip PIC64GX variant
- sdhci-esdhc-imx: Add support for eMMC HW-reset
- sdhci-msm: Add support for the X1E80100/IPQ5424/SAR2130P/QCS615 variants
- sdhci-of-arasan: Add support for eMMC HW-reset
- sdhci-pci-gli: Add UHS-II support for the GL9767/GL9755 variants
MEMSTICK:
- A couple of minor updates"
* tag 'mmc-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (78 commits)
mmc: pwrseq_simple: Handle !RESET_CONTROLLER properly
mmc: mtk-sd: Fix MMC_CAP2_CRYPTO flag setting
mmc: mtk-sd: Fix error handle of probe function
mmc: core: Correction a warning caused by incorrect type in assignment for UHS-II
mmc: sdhci-esdhc-imx: Update esdhc sysctl dtocv bitmask
mmc: sdhci-esdhc-imx: Implement emmc hardware reset
mmc: core: Correct type in variable assignment for UHS-II
mmc: sdhci-uhs2: correction a warning caused by incorrect type in argument
mmc: sdhci-uhs2: Remove unnecessary variables
mmc: sdhci-uhs2: Correct incorrect type in argument
mmc: sdhci: Make MMC_SDHCI_UHS2 config symbol invisible
mmc: sdhci-uhs2: Remove unnecessary NULL check
mmc: core: Fix error paths for UHS-II card init and re-init
mmc: core: Add error handling of sd_uhs2_power_up()
mmc: core: Simplify sd_uhs2_power_up()
mmc: bcm2835: Introduce proper clock handling
mmc: bcm2835: Fix type of current clock speed
dt-bindings: mmc: Add sdhci compatible for QCS615
mmc: core: Use GFP_NOIO in ACMD22
dt-bindings: mmc: sdhci-msm: Add SAR2130P compatible
...
The recent introduction of reset control in pwrseq_simple introduced
a regression for platforms without RESET_CONTROLLER support, because
devm_reset_control_get_optional_shared() would return NULL and make all
resets no-ops. Instead of enforcing this dependency, rely on this behavior
to determine reset support. As a benefit we can get the rid of the
use_reset flag.
Fixes: 73bf4b7381 ("mmc: pwrseq_simple: add support for one reset control")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Message-ID: <20241108130647.8281-1-wahrenst@gmx.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The error path didn't manage the removal of the allocated mmc_card
correctly. Let's fix this to avoid potential memory leaks.
While at it, move the assignment of host->card to slightly later in the
init process and drop also a somewhat silly dev_warn() when CMD8 fails.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241029131752.226764-4-ulf.hansson@linaro.org>
Reset controls being refcounted, they allow to share gpios across
drivers. Right now, reset framework and reset-gpio driver supports only
one reset gpio, so add support for one single reset control. If more
than one reset gpio is configured in the device tree, then fallback to
classic gpio control.
Signed-off-by: Catalin Popescu <catalin.popescu@leica-geosystems.com>
Message-ID: <20241017131957.1171323-1-catalin.popescu@leica-geosystems.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Attach partitions fwnode if found in mmc-card and register disk with it.
This permits block partition to reference the node and register a
partition table defined in DT for the special case for embedded device
that doesn't have a partition table flashed but have an hardcoded
partition table passed from the system.
JEDEC BOOT partition boot0/boot1 are supported but in DT we refer with
the JEDEC name of boot1 and boot2 to better adhere to documentation.
Also JEDEC GP partition gp0/1/2/3 are supported but in DT we refer with
the JEDEC name of gp1/2/3/4 to better adhere to documentration.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241002221306.4403-5-ansuelsmth@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To allow an additional external regulator to be controlled by an mmc host
driver, let's add support for a vqmmc2 regulator to the mmc core.
For an SD UHS-II interface the vqmmc2 regulator may correspond to the so
called vdd2 supply, as described by the SD spec. Initially, only 1.8V is
needed, hence limit the new helper function, mmc_regulator_set_vqmmc2() to
this too.
Note that, to allow for flexibility mmc host drivers need to manage the
enable/disable of the vqmmc2 regulator themselves, while the regulator is
looked up through the common mmc_regulator_get_supply().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20240913102836.6144-5-victorshihgli@gmail.com
To inform the users about SD UHS-II cards, let's extend the print at card
insertion with a "UHS-II" substring. Within this change, it seems
reasonable to convert from using "ultra high speed" into "UHS-I speed", for
the UHS-I type, as it should makes it more clear.
Note that, the new print for UHS-II cards doesn't include the actual
selected speed mode. Instead, this is going to be added from subsequent
change.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20240913102836.6144-4-victorshihgli@gmail.com
The SD UHS-II interface was introduced to the SD spec v4.00 several years
ago. The interface is fundamentally different from an electrical and a
protocol point of view, comparing to the legacy SD interface.
However, the legacy SD protocol is supported through a specific transport
layer (SD-TRAN) defined in the UHS-II addendum of the spec. This allows the
SD card to be managed in a very similar way as a legacy SD card, hence a
lot of code can be re-used to support these new types of cards through the
mmc subsystem.
Moreover, an SD card that supports the UHS-II interface shall also be
backwards compatible with the legacy SD interface, which allows a UHS-II
card to be inserted into a legacy slot. As a matter of fact, this is
already supported by mmc subsystem as of today.
To prepare to add support for UHS-II, this change puts the basic foundation
in the mmc core in place, allowing it to be more easily reviewed before
subsequent changes implements the actual support.
Basically, the approach here adds a new UHS-II bus_ops type and adds a
separate initialization path for the UHS-II card. The intent is to avoid us
from sprinkling the legacy initialization path, but also to simplify
implementation of the UHS-II specific bits.
At this point, there is only one new host ops added to manage the various
ios settings needed for UHS-II. Additional host ops that are needed, are
being added from subsequent changes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20240913102836.6144-3-victorshihgli@gmail.com
The current print of the bus speed mode in mmc_add_card() has grown over
the years and is now difficult to parse. Let's clean up the code and also
take the opportunity to properly announce "DDR" for eMMCs as
"high speed DDR", which is according to the eMMC spec.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20240913102836.6144-2-victorshihgli@gmail.com
hsq allows to get more in-flight requests from mmc core, which can be
prepared in advance and be issued asynchronously to the completion of
the preceding request (in atomic context). This is presumably broken
though by the mandatory CMD22 for SDUC.
We plan to make it work, but only as an improvement on top of the
initial support for SDUC.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20241006051148.160278-10-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
