Merge tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux

Pull MIPS changes from Paul Burton: "Nothing too big or scary in here: - Support mremap() for the VDSO, primarily to allow CRIU to restore the VDSO to its checkpointed location. - Restore the MIPS32 cBPF JIT, after having reverted the enablement of the eBPF JIT for MIPS32 systems in the 5.5 cycle. - Improve cop0 counter synchronization behaviour whilst onlining CPUs by running with interrupts disabled. - Better match FPU behaviour when emulating multiply-accumulate instructions on pre-r6 systems that implement IEEE754-2008 style MACs. - Loongson64 kernels now build using the MIPS64r2 ISA, allowing them to take advantage of instructions introduced by r2. - Support for the Ingenic X1000 SoC & the really nice little CU Neo development board that's using it. - Support for WMAC on GARDENA Smart Gateway devices. - Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in preparation for introducing IP35 (Origin 3*) support. - Various Kconfig & Makefile cleanups" * tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits) MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel MIPS: Loongson64: Disable exec hazard MIPS: Loongson64: Bump ISA level to MIPSR2 MIPS: Make DIEI support as a config option MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too" MIPS: asm: local: add barriers for Loongson MIPS: Loongson64: Select mac2008 only feature MIPS: Add MAC2008 Support Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel" MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again) MIPS: make CPU_HAS_LOAD_STORE_LR opt-out MIPS: generic: don't unconditionally select PINCTRL MIPS: don't explicitly select LIBFDT in Kconfig MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts MIPS: SGI-IP30: Check for valid pointer before using it MIPS: syscalls: fix indentation of the 'SYSNR' message MIPS: boot: fix typo in 'vmlinux.lzma.its' target MIPS: fix indentation of the 'RELOCS' message dt-bindings: Document loongson vendor-prefix MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi. ...
2026-03-06 15:25:10 -08:00 · 2020-01-31 11:28:31 -08:00
parent b7e573bb4a 2c42887198
commit c5951e7c8e
95 changed files with 3889 additions and 1240 deletions
--- a/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
+++ b/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
@@ -0,0 +1,35 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/ingenic/devices.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ingenic XBurst based Platforms Device Tree Bindings
+
+maintainers:
+  - 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
+description: |
+  Devices with a Ingenic XBurst CPU shall have the following properties.
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+
+      - description: Qi Hardware Ben NanoNote
+        items:
+          - const: qi,lb60
+
+      - description: Game Consoles Worldwide GCW Zero
+        items:
+          - const: gcw,zero
+
+      - description: MIPS Creator CI20
+        items:
+          - const: img,ci20
+
+      - description: YSH & ATIL General Board CU Neo
+        items:
+          - const: yna,cu1000-neo
+...
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -555,6 +555,8 @@ patternProperties:
    description: Logic PD, Inc.
  "^longcheer,.*":
    description: Longcheer Technology (Shanghai) Co., Ltd.
+  "^loongson,.*":
+    description: Loongson Technology Corporation Limited
  "^lsi,.*":
    description: LSI Corp. (LSI Logic)
  "^lwn,.*":
@@ -1084,6 +1086,8 @@ patternProperties:
    description: Shenzhen Xunlong Software CO.,Limited
  "^xylon,.*":
    description: Xylon
+  "^yna,.*":
+    description: YSH & ATIL
  "^yones-toptech,.*":
    description: Yones Toptech Co., Ltd.
  "^ysoft,.*":
--- a/1
+++ b/1
@@ -11116,7 +11116,6 @@ F:	drivers/usb/image/microtek.*
 MIPS
 M:	Ralf Baechle <ralf@linux-mips.org>
 M:	Paul Burton <paulburton@kernel.org>
-M:	James Hogan <jhogan@kernel.org>
 L:	linux-mips@vger.kernel.org
 W:	http://www.linux-mips.org/
 T:	git git://git.linux-mips.org/pub/scm/ralf/linux.git
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -5,9 +5,11 @@ config MIPS
 	select ARCH_32BIT_OFF_T if !64BIT
 	select ARCH_BINFMT_ELF_STATE if MIPS_FP_SUPPORT
 	select ARCH_CLOCKSOURCE_DATA
+	select ARCH_HAS_FORTIFY_SOURCE
+	select ARCH_HAS_KCOV
+	select ARCH_HAS_PTE_SPECIAL if !(32BIT && CPU_HAS_RIXI)
 	select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST
 	select ARCH_HAS_UBSAN_SANITIZE_ALL
-	select ARCH_HAS_FORTIFY_SOURCE
 	select ARCH_SUPPORTS_UPROBES
 	select ARCH_USE_BUILTIN_BSWAP
 	select ARCH_USE_CMPXCHG_LOCKREF if 64BIT
@@ -47,7 +49,7 @@ config MIPS
 	select HAVE_ARCH_TRACEHOOK
 	select HAVE_ARCH_TRANSPARENT_HUGEPAGE if CPU_SUPPORTS_HUGEPAGES
 	select HAVE_ASM_MODVERSIONS
-	select HAVE_EBPF_JIT if 64BIT && !CPU_MICROMIPS && TARGET_ISA_REV >= 2
+	select HAVE_CBPF_JIT if !64BIT && !CPU_MICROMIPS
 	select HAVE_CONTEXT_TRACKING
 	select HAVE_COPY_THREAD_TLS
 	select HAVE_C_RECORDMCOUNT
@@ -55,11 +57,14 @@ config MIPS
 	select HAVE_DEBUG_STACKOVERFLOW
 	select HAVE_DMA_CONTIGUOUS
 	select HAVE_DYNAMIC_FTRACE
+	select HAVE_EBPF_JIT if 64BIT && !CPU_MICROMIPS && TARGET_ISA_REV >= 2
 	select HAVE_EXIT_THREAD
 	select HAVE_FAST_GUP
 	select HAVE_FTRACE_MCOUNT_RECORD
 	select HAVE_FUNCTION_GRAPH_TRACER
 	select HAVE_FUNCTION_TRACER
+	select HAVE_GCC_PLUGINS
+	select HAVE_GENERIC_VDSO
 	select HAVE_IDE
 	select HAVE_IOREMAP_PROT
 	select HAVE_IRQ_EXIT_ON_IRQ_STACK
@@ -78,18 +83,14 @@ config MIPS
 	select HAVE_STACKPROTECTOR
 	select HAVE_SYSCALL_TRACEPOINTS
 	select HAVE_VIRT_CPU_ACCOUNTING_GEN if 64BIT || !SMP
-	select HAVE_GENERIC_VDSO
 	select IRQ_FORCED_THREADING
 	select ISA if EISA
-	select MODULES_USE_ELF_RELA if MODULES && 64BIT
 	select MODULES_USE_ELF_REL if MODULES
+	select MODULES_USE_ELF_RELA if MODULES && 64BIT
 	select PERF_USE_VMALLOC
 	select RTC_LIB
 	select SYSCTL_EXCEPTION_TRACE
 	select VIRT_TO_BUS
-	select ARCH_HAS_PTE_SPECIAL if !(32BIT && CPU_HAS_RIXI)
-	select ARCH_HAS_KCOV
-	select HAVE_GCC_PLUGINS

 menu "Machine selection"

@@ -104,20 +105,18 @@ config MIPS_GENERIC
 	select CEVT_R4K
 	select CLKSRC_MIPS_GIC
 	select COMMON_CLK
-	select CPU_MIPSR2_IRQ_VI
 	select CPU_MIPSR2_IRQ_EI
+	select CPU_MIPSR2_IRQ_VI
 	select CSRC_R4K
 	select DMA_PERDEV_COHERENT
 	select HAVE_PCI
 	select IRQ_MIPS_CPU
-	select LIBFDT
 	select MIPS_AUTO_PFN_OFFSET
 	select MIPS_CPU_SCACHE
 	select MIPS_GIC
 	select MIPS_L1_CACHE_SHIFT_7
 	select NO_EXCEPT_FILL
 	select PCI_DRIVERS_GENERIC
-	select PINCTRL
 	select SMP_UP if SMP
 	select SWAP_IO_SPACE
 	select SYS_HAS_CPU_MIPS32_R1
@@ -132,11 +131,12 @@ config MIPS_GENERIC
 	select SYS_SUPPORTS_HIGHMEM
 	select SYS_SUPPORTS_LITTLE_ENDIAN
 	select SYS_SUPPORTS_MICROMIPS
-	select SYS_SUPPORTS_MIPS_CPS
 	select SYS_SUPPORTS_MIPS16
+	select SYS_SUPPORTS_MIPS_CPS
 	select SYS_SUPPORTS_MULTITHREADING
 	select SYS_SUPPORTS_RELOCATABLE
 	select SYS_SUPPORTS_SMARTMIPS
+	select UHI_BOOT
 	select USB_EHCI_BIG_ENDIAN_DESC if CPU_BIG_ENDIAN
 	select USB_EHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
 	select USB_OHCI_BIG_ENDIAN_DESC if CPU_BIG_ENDIAN
@@ -144,7 +144,6 @@ config MIPS_GENERIC
 	select USB_UHCI_BIG_ENDIAN_DESC if CPU_BIG_ENDIAN
 	select USB_UHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
 	select USE_OF
-	select UHI_BOOT
 	help
 	  Select this to build a kernel which aims to support multiple boards,
 	  generally using a flattened device tree passed from the bootloader
@@ -403,7 +402,6 @@ config MACH_INGENIC
 	select GENERIC_IRQ_CHIP
 	select BUILTIN_DTB if MIPS_NO_APPENDED_DTB
 	select USE_OF
-	select LIBFDT

 config LANTIQ
 	bool "Lantiq based platforms"
@@ -510,7 +508,6 @@ config MACH_PISTACHIO
 	select DMA_NONCOHERENT
 	select GPIOLIB
 	select IRQ_MIPS_CPU
-	select LIBFDT
 	select MFD_SYSCON
 	select MIPS_CPU_SCACHE
 	select MIPS_GIC
@@ -548,7 +545,6 @@ config MIPS_MALTA
 	select I8253
 	select I8259
 	select IRQ_MIPS_CPU
-	select LIBFDT
 	select MIPS_BONITO64
 	select MIPS_CPU_SCACHE
 	select MIPS_GIC
@@ -980,7 +976,6 @@ config CAVIUM_OCTEON_SOC
 	select ZONE_DMA32
 	select HOLES_IN_ZONE
 	select GPIOLIB
-	select LIBFDT
 	select USE_OF
 	select ARCH_SPARSEMEM_ENABLE
 	select SYS_SUPPORTS_SMP
@@ -1223,8 +1218,7 @@ config NO_IOPORT_MAP
 	def_bool n

 config GENERIC_CSUM
-	bool
-	default y if !CPU_HAS_LOAD_STORE_LR
+	def_bool CPU_NO_LOAD_STORE_LR

 config GENERIC_ISA_DMA
 	bool
@@ -1442,11 +1436,14 @@ config CPU_LOONGSON64
 	bool "Loongson 64-bit CPU"
 	depends on SYS_HAS_CPU_LOONGSON64
 	select ARCH_HAS_PHYS_TO_DMA
+	select CPU_MIPSR2
+	select CPU_HAS_PREFETCH
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select CPU_SUPPORTS_HIGHMEM
 	select CPU_SUPPORTS_HUGEPAGES
 	select CPU_SUPPORTS_MSA
-	select CPU_HAS_LOAD_STORE_LR
+	select CPU_DIEI_BROKEN if !LOONGSON3_ENHANCEMENT
+	select CPU_MIPSR2_IRQ_VI
 	select WEAK_ORDERING
 	select WEAK_REORDERING_BEYOND_LLSC
 	select MIPS_ASID_BITS_VARIABLE
@@ -1464,8 +1461,6 @@ config CPU_LOONGSON64
 config LOONGSON3_ENHANCEMENT
 	bool "New Loongson-3 CPU Enhancements"
 	default n
-	select CPU_MIPSR2
-	select CPU_HAS_PREFETCH
 	depends on CPU_LOONGSON64
 	help
 	  New Loongson-3 cores (since Loongson-3A R2, as opposed to Loongson-3A
@@ -1542,7 +1537,6 @@ config CPU_MIPS32_R1
 	bool "MIPS32 Release 1"
 	depends on SYS_HAS_CPU_MIPS32_R1
 	select CPU_HAS_PREFETCH
-	select CPU_HAS_LOAD_STORE_LR
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_HIGHMEM
 	help
@@ -1560,7 +1554,6 @@ config CPU_MIPS32_R2
 	bool "MIPS32 Release 2"
 	depends on SYS_HAS_CPU_MIPS32_R2
 	select CPU_HAS_PREFETCH
-	select CPU_HAS_LOAD_STORE_LR
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_HIGHMEM
 	select CPU_SUPPORTS_MSA
@@ -1576,6 +1569,7 @@ config CPU_MIPS32_R6
 	bool "MIPS32 Release 6"
 	depends on SYS_HAS_CPU_MIPS32_R6
 	select CPU_HAS_PREFETCH
+	select CPU_NO_LOAD_STORE_LR
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_HIGHMEM
 	select CPU_SUPPORTS_MSA
@@ -1591,7 +1585,6 @@ config CPU_MIPS64_R1
 	bool "MIPS64 Release 1"
 	depends on SYS_HAS_CPU_MIPS64_R1
 	select CPU_HAS_PREFETCH
-	select CPU_HAS_LOAD_STORE_LR
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select CPU_SUPPORTS_HIGHMEM
@@ -1611,7 +1604,6 @@ config CPU_MIPS64_R2
 	bool "MIPS64 Release 2"
 	depends on SYS_HAS_CPU_MIPS64_R2
 	select CPU_HAS_PREFETCH
-	select CPU_HAS_LOAD_STORE_LR
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select CPU_SUPPORTS_HIGHMEM
@@ -1629,6 +1621,7 @@ config CPU_MIPS64_R6
 	bool "MIPS64 Release 6"
 	depends on SYS_HAS_CPU_MIPS64_R6
 	select CPU_HAS_PREFETCH
+	select CPU_NO_LOAD_STORE_LR
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select CPU_SUPPORTS_HIGHMEM
@@ -1646,7 +1639,6 @@ config CPU_R3000
 	bool "R3000"
 	depends on SYS_HAS_CPU_R3000
 	select CPU_HAS_WB
-	select CPU_HAS_LOAD_STORE_LR
 	select CPU_R3K_TLB
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_HIGHMEM
@@ -1662,7 +1654,6 @@ config CPU_TX39XX
 	bool "R39XX"
 	depends on SYS_HAS_CPU_TX39XX
 	select CPU_SUPPORTS_32BIT_KERNEL
-	select CPU_HAS_LOAD_STORE_LR
 	select CPU_R3K_TLB

 config CPU_VR41XX
@@ -1670,7 +1661,6 @@ config CPU_VR41XX
 	depends on SYS_HAS_CPU_VR41XX
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_64BIT_KERNEL
-	select CPU_HAS_LOAD_STORE_LR
 	help
 	  The options selects support for the NEC VR4100 series of processors.
 	  Only choose this option if you have one of these processors as a
@@ -1683,7 +1673,6 @@ config CPU_R4X00
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select CPU_SUPPORTS_HUGEPAGES
-	select CPU_HAS_LOAD_STORE_LR
 	help
 	  MIPS Technologies R4000-series processors other than 4300, including
 	  the R4000, R4400, R4600, and 4700.
@@ -1692,7 +1681,6 @@ config CPU_TX49XX
 	bool "R49XX"
 	depends on SYS_HAS_CPU_TX49XX
 	select CPU_HAS_PREFETCH
-	select CPU_HAS_LOAD_STORE_LR
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select CPU_SUPPORTS_HUGEPAGES
@@ -1703,7 +1691,6 @@ config CPU_R5000
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select CPU_SUPPORTS_HUGEPAGES
-	select CPU_HAS_LOAD_STORE_LR
 	help
 	  MIPS Technologies R5000-series processors other than the Nevada.

@@ -1713,7 +1700,6 @@ config CPU_R5500
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select CPU_SUPPORTS_HUGEPAGES
-	select CPU_HAS_LOAD_STORE_LR
 	help
 	  NEC VR5500 and VR5500A series processors implement 64-bit MIPS IV
 	  instruction set.
@@ -1724,7 +1710,6 @@ config CPU_NEVADA
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select CPU_SUPPORTS_HUGEPAGES
-	select CPU_HAS_LOAD_STORE_LR
 	help
 	  QED / PMC-Sierra RM52xx-series ("Nevada") processors.

@@ -1732,7 +1717,6 @@ config CPU_R10000
 	bool "R10000"
 	depends on SYS_HAS_CPU_R10000
 	select CPU_HAS_PREFETCH
-	select CPU_HAS_LOAD_STORE_LR
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select CPU_SUPPORTS_HIGHMEM
@@ -1744,7 +1728,6 @@ config CPU_RM7000
 	bool "RM7000"
 	depends on SYS_HAS_CPU_RM7000
 	select CPU_HAS_PREFETCH
-	select CPU_HAS_LOAD_STORE_LR
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select CPU_SUPPORTS_HIGHMEM
@@ -1753,7 +1736,6 @@ config CPU_RM7000
 config CPU_SB1
 	bool "SB1"
 	depends on SYS_HAS_CPU_SB1
-	select CPU_HAS_LOAD_STORE_LR
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select CPU_SUPPORTS_HIGHMEM
@@ -1764,7 +1746,6 @@ config CPU_CAVIUM_OCTEON
 	bool "Cavium Octeon processor"
 	depends on SYS_HAS_CPU_CAVIUM_OCTEON
 	select CPU_HAS_PREFETCH
-	select CPU_HAS_LOAD_STORE_LR
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select WEAK_ORDERING
 	select CPU_SUPPORTS_HIGHMEM
@@ -1794,7 +1775,6 @@ config CPU_BMIPS
 	select WEAK_ORDERING
 	select CPU_SUPPORTS_HIGHMEM
 	select CPU_HAS_PREFETCH
-	select CPU_HAS_LOAD_STORE_LR
 	select CPU_SUPPORTS_CPUFREQ
 	select MIPS_EXTERNAL_TIMER
 	help
@@ -1803,7 +1783,6 @@ config CPU_BMIPS
 config CPU_XLR
 	bool "Netlogic XLR SoC"
 	depends on SYS_HAS_CPU_XLR
-	select CPU_HAS_LOAD_STORE_LR
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select CPU_SUPPORTS_HIGHMEM
@@ -1822,7 +1801,6 @@ config CPU_XLP
 	select WEAK_ORDERING
 	select WEAK_REORDERING_BEYOND_LLSC
 	select CPU_HAS_PREFETCH
-	select CPU_HAS_LOAD_STORE_LR
 	select CPU_MIPSR2
 	select CPU_SUPPORTS_HUGEPAGES
 	select MIPS_ASID_BITS_VARIABLE
@@ -1928,14 +1906,12 @@ config CPU_LOONGSON2EF
 	select CPU_SUPPORTS_HIGHMEM
 	select CPU_SUPPORTS_HUGEPAGES
 	select ARCH_HAS_PHYS_TO_DMA
-	select CPU_HAS_LOAD_STORE_LR

 config CPU_LOONGSON32
 	bool
 	select CPU_MIPS32
 	select CPU_MIPSR2
 	select CPU_HAS_PREFETCH
-	select CPU_HAS_LOAD_STORE_LR
 	select CPU_SUPPORTS_32BIT_KERNEL
 	select CPU_SUPPORTS_HIGHMEM
 	select CPU_SUPPORTS_CPUFREQ
@@ -2110,12 +2086,14 @@ config CPU_MIPSR2
 	bool
 	default y if CPU_MIPS32_R2 || CPU_MIPS64_R2 || CPU_CAVIUM_OCTEON
 	select CPU_HAS_RIXI
+	select CPU_HAS_DIEI if !CPU_DIEI_BROKEN
 	select MIPS_SPRAM

 config CPU_MIPSR6
 	bool
 	default y if CPU_MIPS32_R6 || CPU_MIPS64_R6
 	select CPU_HAS_RIXI
+	select CPU_HAS_DIEI if !CPU_DIEI_BROKEN
 	select HAVE_ARCH_BITREVERSE
 	select MIPS_ASID_BITS_VARIABLE
 	select MIPS_CRC_SUPPORT
@@ -2575,15 +2553,23 @@ config CPU_HAS_WB
 config XKS01
 	bool

+config CPU_HAS_DIEI
+	depends on !CPU_DIEI_BROKEN
+	bool
+
+config CPU_DIEI_BROKEN
+	bool
+
 config CPU_HAS_RIXI
 	bool

-config CPU_HAS_LOAD_STORE_LR
+config CPU_NO_LOAD_STORE_LR
 	bool
 	help
-	  CPU has support for unaligned load and store instructions:
+	  CPU lacks support for unaligned load and store instructions:
 	  LWL, LWR, SWL, SWR (Load/store word left/right).
-	  LDL, LDR, SDL, SDR (Load/store doubleword left/right, for 64bit systems).
+	  LDL, LDR, SDL, SDR (Load/store doubleword left/right, for 64bit
+	  systems).

 #
 # Vectored interrupt mode is an R2 feature
@@ -2696,6 +2682,14 @@ config NUMA
 config SYS_SUPPORTS_NUMA
 	bool

+config HAVE_SETUP_PER_CPU_AREA
+	def_bool y
+	depends on NUMA
+
+config NEED_PER_CPU_EMBED_FIRST_CHUNK
+	def_bool y
+	depends on NUMA
+
 config RELOCATABLE
 	bool "Relocatable kernel"
 	depends on SYS_SUPPORTS_RELOCATABLE && (CPU_MIPS32_R2 || CPU_MIPS64_R2 || CPU_MIPS32_R6 || CPU_MIPS64_R6 || CAVIUM_OCTEON_SOC)
--- a/arch/mips/Makefile.postlink
+++ b/arch/mips/Makefile.postlink
@@ -17,7 +17,7 @@ quiet_cmd_ls3_llsc = LLSCCHK $@
      cmd_ls3_llsc = $(CMD_LS3_LLSC) $@

 CMD_RELOCS = arch/mips/boot/tools/relocs
-quiet_cmd_relocs = RELOCS $@
+quiet_cmd_relocs = RELOCS  $@
      cmd_relocs = $(CMD_RELOCS) $@

 # `@true` prevents complaint when there is nothing to be done
--- a/arch/mips/boot/Makefile
+++ b/arch/mips/boot/Makefile
@@ -123,7 +123,7 @@ $(obj)/vmlinux.its.S: $(addprefix $(srctree)/arch/mips/$(PLATFORM)/,$(ITS_INPUTS
 targets += vmlinux.its
 targets += vmlinux.gz.its
 targets += vmlinux.bz2.its
-targets += vmlinux.lzmo.its
+targets += vmlinux.lzma.its
 targets += vmlinux.lzo.its

 quiet_cmd_cpp_its_S = ITS     $@
--- a/arch/mips/boot/dts/ingenic/Makefile
+++ b/arch/mips/boot/dts/ingenic/Makefile
@@ -2,5 +2,6 @@
 dtb-$(CONFIG_JZ4740_QI_LB60)	+= qi_lb60.dtb
 dtb-$(CONFIG_JZ4770_GCW0)	+= gcw0.dtb
 dtb-$(CONFIG_JZ4780_CI20)	+= ci20.dtb
+dtb-$(CONFIG_X1000_CU1000_NEO)	+= cu1000-neo.dtb

 obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))
--- a/arch/mips/boot/dts/ingenic/cu1000-neo.dts
+++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "x1000.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "yna,cu1000-neo", "ingenic,x1000";
+	model = "YSH & ATIL General Board CU Neo";
+
+	aliases {
+		serial2 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x04000000>;
+	};
+
+	wlan_pwrseq: msc1-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&lpoclk>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpc 17 GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <200>;
+
+		lpoclk: ap6212a {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+};
+
+&exclk {
+	clock-frequency = <24000000>;
+};
+
+&tcu {
+	/* 1500 kHz for the system timer and clocksource */
+	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
+	assigned-clock-rates = <1500000>, <1500000>;
+
+	/* Use channel #0 for the system timer channel #2 for the clocksource */
+	ingenic,pwm-channels-mask = <0xfa>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_i2c0>;
+
+	ads7830@48 {
+		compatible = "ti,ads7830";
+		reg = <0x48>;
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_uart2>;
+
+	status = "okay";
+};
+
+&mac {
+	phy-mode = "rmii";
+	phy-handle = <&lan8720a>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mac>;
+
+	snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 30000>;
+
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+
+	lan8720a: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0007.c0f0", "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&msc0 {
+	bus-width = <8>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_msc0>;
+
+	non-removable;
+
+	status = "okay";
+};
+
+&msc1 {
+	bus-width = <4>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_msc1>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	non-removable;
+
+	mmc-pwrseq = <&wlan_pwrseq>;
+
+	status = "okay";
+
+	ap6212a: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupt-parent = <&gpc>;
+		interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		brcm,drive-strength = <10>;
+	};
+};
+
+&pinctrl {
+	pins_i2c0: i2c0 {
+		function = "i2c0";
+		groups = "i2c0-data";
+		bias-disable;
+	};
+
+	pins_uart2: uart2 {
+		function = "uart2";
+		groups = "uart2-data-d";
+		bias-disable;
+	};
+
+	pins_mac: mac {
+		function = "mac";
+		groups = "mac";
+		bias-disable;
+	};
+
+	pins_msc0: msc0 {
+		function = "mmc0";
+		groups = "mmc0-1bit", "mmc0-4bit", "mmc0-8bit";
+		bias-disable;
+	};
+
+	pins_msc1: msc1 {
+		function = "mmc1";
+		groups = "mmc1-1bit", "mmc1-4bit";
+		bias-disable;
+	};
+};
--- a/arch/mips/boot/dts/ingenic/x1000.dtsi
+++ b/arch/mips/boot/dts/ingenic/x1000.dtsi
@@ -0,0 +1,317 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/x1000-cgu.h>
+#include <dt-bindings/dma/x1000-dma.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ingenic,x1000", "ingenic,x1000e";
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	intc: interrupt-controller@10001000 {
+		compatible = "ingenic,x1000-intc", "ingenic,jz4780-intc";
+		reg = <0x10001000 0x50>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <2>;
+	};
+
+	exclk: ext {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+
+	rtclk: rtc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	cgu: x1000-cgu@10000000 {
+		compatible = "ingenic,x1000-cgu";
+		reg = <0x10000000 0x100>;
+
+		#clock-cells = <1>;
+
+		clocks = <&exclk>, <&rtclk>;
+		clock-names = "ext", "rtc";
+	};
+
+	tcu: timer@10002000 {
+		compatible = "ingenic,x1000-tcu",
+				 "ingenic,jz4770-tcu",
+				 "simple-mfd";
+		reg = <0x10002000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10002000 0x1000>;
+
+		#clock-cells = <1>;
+
+		clocks = <&cgu X1000_CLK_RTCLK
+			  &cgu X1000_CLK_EXCLK
+			  &cgu X1000_CLK_PCLK>;
+		clock-names = "rtc", "ext", "pclk";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <27 26 25>;
+
+		wdt: watchdog@0 {
+			compatible = "ingenic,x1000-watchdog", "ingenic,jz4780-watchdog";
+			reg = <0x0 0x10>;
+
+			clocks = <&cgu X1000_CLK_RTCLK>;
+			clock-names = "wdt";
+		};
+	};
+
+	rtc: rtc@10003000 {
+		compatible = "ingenic,x1000-rtc", "ingenic,jz4780-rtc";
+		reg = <0x10003000 0x4c>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <32>;
+
+		clocks = <&cgu X1000_CLK_RTCLK>;
+		clock-names = "rtc";
+	};
+
+	pinctrl: pin-controller@10010000 {
+		compatible = "ingenic,x1000-pinctrl";
+		reg = <0x10010000 0x800>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpa: gpio@0 {
+			compatible = "ingenic,x1000-gpio";
+			reg = <0>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 0 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <17>;
+		};
+
+		gpb: gpio@1 {
+			compatible = "ingenic,x1000-gpio";
+			reg = <1>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 32 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <16>;
+		};
+
+		gpc: gpio@2 {
+			compatible = "ingenic,x1000-gpio";
+			reg = <2>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 64 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <15>;
+		};
+
+		gpd: gpio@3 {
+			compatible = "ingenic,x1000-gpio";
+			reg = <3>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 96 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <14>;
+		};
+	};
+
+	i2c0: i2c-controller@10050000 {
+		compatible = "ingenic,x1000-i2c";
+		reg = <0x10050000 0x1000>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <60>;
+
+		clocks = <&cgu X1000_CLK_I2C0>;
+
+		status = "disabled";
+	};
+
+	i2c1: i2c-controller@10051000 {
+		compatible = "ingenic,x1000-i2c";
+		reg = <0x10051000 0x1000>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <59>;
+
+		clocks = <&cgu X1000_CLK_I2C1>;
+
+		status = "disabled";
+	};
+
+	i2c2: i2c-controller@10052000 {
+		compatible = "ingenic,x1000-i2c";
+		reg = <0x10052000 0x1000>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <58>;
+
+		clocks = <&cgu X1000_CLK_I2C2>;
+
+		status = "disabled";
+	};
+
+	uart0: serial@10030000 {
+		compatible = "ingenic,x1000-uart";
+		reg = <0x10030000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <51>;
+
+		clocks = <&exclk>, <&cgu X1000_CLK_UART0>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	uart1: serial@10031000 {
+		compatible = "ingenic,x1000-uart";
+		reg = <0x10031000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <50>;
+
+		clocks = <&exclk>, <&cgu X1000_CLK_UART1>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	uart2: serial@10032000 {
+		compatible = "ingenic,x1000-uart";
+		reg = <0x10032000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <49>;
+
+		clocks = <&exclk>, <&cgu X1000_CLK_UART2>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	pdma: dma-controller@13420000 {
+		compatible = "ingenic,x1000-dma";
+		reg = <0x13420000 0x400
+			   0x13421000 0x40>;
+		#dma-cells = <2>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <10>;
+
+		clocks = <&cgu X1000_CLK_PDMA>;
+	};
+
+	mac: ethernet@134b0000 {
+		compatible = "ingenic,x1000-mac", "snps,dwmac";
+		reg = <0x134b0000 0x2000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <55>;
+		interrupt-names = "macirq";
+
+		clocks = <&cgu X1000_CLK_MAC>;
+		clock-names = "stmmaceth";
+
+		status = "disabled";
+
+		mdio: mdio {
+			compatible = "snps,dwmac-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+	};
+
+	msc0: mmc@13450000 {
+		compatible = "ingenic,x1000-mmc";
+		reg = <0x13450000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <37>;
+
+		clocks = <&cgu X1000_CLK_MSC0>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+
+		dmas = <&pdma X1000_DMA_MSC0_RX 0xffffffff>,
+			   <&pdma X1000_DMA_MSC0_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	msc1: mmc@13460000 {
+		compatible = "ingenic,x1000-mmc";
+		reg = <0x13460000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <36>;
+
+		clocks = <&cgu X1000_CLK_MSC1>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+
+		dmas = <&pdma X1000_DMA_MSC1_RX 0xffffffff>,
+			   <&pdma X1000_DMA_MSC1_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+};
--- a/arch/mips/boot/dts/ralink/gardena_smart_gateway_mt7688.dts
+++ b/arch/mips/boot/dts/ralink/gardena_smart_gateway_mt7688.dts
@@ -177,6 +177,9 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinmux_i2s_gpio>;		/* GPIO0..3 */

+	fifo-size = <8>;
+	tx-threshold = <8>;
+
 	rts-gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
 	cts-gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
 };
@@ -195,3 +198,8 @@
 &watchdog {
 	status = "okay";
 };
+
+&wmac {
+	status = "okay";
+	mediatek,mtd-eeprom = <&factory 0x0000>;
+};
--- a/arch/mips/boot/dts/ralink/mt7628a.dtsi
+++ b/arch/mips/boot/dts/ralink/mt7628a.dtsi
@@ -285,4 +285,14 @@
 		interrupt-parent = <&intc>;
 		interrupts = <18>;
 	};
+
+	wmac: wmac@10300000 {
+		compatible = "mediatek,mt7628-wmac";
+		reg = <0x10300000 0x100000>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <6>;
+
+		status = "disabled";
+	};
 };
--- a/arch/mips/cavium-octeon/octeon-irq.c
+++ b/arch/mips/cavium-octeon/octeon-irq.c
@@ -2193,7 +2193,7 @@ static int octeon_irq_cib_map(struct irq_domain *d,
 	struct octeon_irq_cib_chip_data *cd;

 	if (hw >= host_data->max_bits) {
-		pr_err("ERROR: %s mapping %u is to big!\n",
+		pr_err("ERROR: %s mapping %u is too big!\n",
 		       irq_domain_get_of_node(d)->name, (unsigned)hw);
 		return -EINVAL;
 	}
--- a/arch/mips/configs/cu1000-neo_defconfig
+++ b/arch/mips/configs/cu1000-neo_defconfig
@@ -0,0 +1,117 @@
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_KERNEL_GZIP=y
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_MEMCG=y
+CONFIG_MEMCG_KMEM=y
+CONFIG_CGROUP_SCHED=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MACH_INGENIC=y
+CONFIG_X1000_CU1000_NEO=y
+CONFIG_HIGHMEM=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+# CONFIG_SUSPEND is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_COMPACTION is not set
+CONFIG_CMA=y
+CONFIG_CMA_AREAS=7
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_CFG80211=y
+CONFIG_UEVENT_HELPER=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+CONFIG_NETDEVICES=y
+CONFIG_STMMAC_ETH=y
+CONFIG_SMSC_PHY=y
+CONFIG_BRCMFMAC=y
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=2
+CONFIG_SERIAL_EARLYCON=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=3
+CONFIG_SERIAL_8250_RUNTIME_UARTS=3
+CONFIG_SERIAL_8250_INGENIC=y
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C=y
+CONFIG_I2C_JZ4780=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_SENSORS_ADS7828=y
+CONFIG_WATCHDOG=y
+CONFIG_JZ4740_WDT=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
+# CONFIG_VGA_CONSOLE is not set
+# CONFIG_HID is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+CONFIG_MMC_JZ4740=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_JZ4740=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_JZ4780=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_NVMEM=y
+CONFIG_NVMEM_SYSFS=y
+CONFIG_EXT4_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_AUTOFS_FS=y
+CONFIG_PROC_KCORE=y
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_NFS_FS=y
+CONFIG_NLS=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_CODEPAGE_950=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_ECHAINIV=y
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_PRINTK_TIME=y
+CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
+CONFIG_CONSOLE_LOGLEVEL_QUIET=15
+CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7
+CONFIG_DEBUG_INFO=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_PANIC_ON_OOPS=y
+CONFIG_PANIC_TIMEOUT=10
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_STACKTRACE=y
+# CONFIG_FTRACE is not set
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="earlycon clk_ignore_unused"
--- a/arch/mips/configs/generic/board-ocelot.config
+++ b/arch/mips/configs/generic/board-ocelot.config
@@ -41,6 +41,7 @@ CONFIG_SPI_DESIGNWARE=y
 CONFIG_SPI_DW_MMIO=y
 CONFIG_SPI_SPIDEV=y

+CONFIG_PINCTRL=y
 CONFIG_PINCTRL_OCELOT=y

 CONFIG_GPIO_SYSFS=y
--- a/arch/mips/include/asm/Kbuild
+++ b/arch/mips/include/asm/Kbuild
@@ -19,6 +19,7 @@ generic-y += preempt.h
 generic-y += qrwlock.h
 generic-y += qspinlock.h
 generic-y += sections.h
+generic-y += serial.h
 generic-y += trace_clock.h
 generic-y += unaligned.h
 generic-y += user.h
--- a/arch/mips/include/asm/bootinfo.h
+++ b/arch/mips/include/asm/bootinfo.h
@@ -81,6 +81,7 @@ enum loongson2ef_machine_type {
 #define  MACH_INGENIC_JZ4770	2	/* JZ4770 SOC		*/
 #define  MACH_INGENIC_JZ4780	3	/* JZ4780 SOC		*/
 #define  MACH_INGENIC_X1000		4	/* X1000 SOC		*/
+#define  MACH_INGENIC_X1830		5	/* X1830 SOC		*/

 extern char *system_type;
 const char *get_system_type(void);
--- a/arch/mips/include/asm/cpu-features.h
+++ b/arch/mips/include/asm/cpu-features.h
@@ -555,6 +555,10 @@
 # define cpu_has_perf		__opt(MIPS_CPU_PERF)
 #endif

+#ifndef cpu_has_mac2008_only
+# define cpu_has_mac2008_only	__opt(MIPS_CPU_MAC_2008_ONLY)
+#endif
+
 #ifdef CONFIG_SMP
 /*
 * Some systems share FTLB RAMs between threads within a core (siblings in
--- a/arch/mips/include/asm/cpu.h
+++ b/arch/mips/include/asm/cpu.h
@@ -46,7 +46,7 @@
 #define PRID_COMP_NETLOGIC	0x0c0000
 #define PRID_COMP_CAVIUM	0x0d0000
 #define PRID_COMP_LOONGSON	0x140000
-#define PRID_COMP_INGENIC_D0	0xd00000	/* JZ4740, JZ4750 */
+#define PRID_COMP_INGENIC_D0	0xd00000	/* JZ4740, JZ4750, X1830 */
 #define PRID_COMP_INGENIC_D1	0xd10000	/* JZ4770, JZ4775, X1000 */
 #define PRID_COMP_INGENIC_E1	0xe10000	/* JZ4780 */

@@ -185,7 +185,8 @@
 * These are the PRID's for when 23:16 == PRID_COMP_INGENIC_*
 */

-#define PRID_IMP_XBURST	       0x0200
+#define PRID_IMP_XBURST_REV1	0x0200	/* XBurst with MXU SIMD ISA		*/
+#define PRID_IMP_XBURST_REV2	0x0100	/* XBurst with MXU2 SIMD ISA	*/

 /*
 * These are the PRID's for when 23:16 == PRID_COMP_NETLOGIC
@@ -415,6 +416,7 @@ enum cpu_type_enum {
 #define MIPS_CPU_MT_PER_TC_PERF_COUNTERS \
 				BIT_ULL(56)	/* CPU has perf counters implemented per TC (MIPSMT ASE) */
 #define MIPS_CPU_MMID		BIT_ULL(57)	/* CPU supports MemoryMapIDs */
+#define MIPS_CPU_MAC_2008_ONLY	BIT_ULL(58)	/* CPU Only support MAC2008 Fused multiply-add instruction */

 /*
 * CPU ASE encodings
--- a/arch/mips/include/asm/gio_device.h
+++ b/arch/mips/include/asm/gio_device.h
@@ -32,8 +32,6 @@ struct gio_driver {
 };
 #define to_gio_driver(drv) container_of(drv, struct gio_driver, driver)

-extern const struct gio_device_id *gio_match_device(const struct gio_device_id *,
-						    const struct gio_device *);
 extern struct gio_device *gio_dev_get(struct gio_device *);
 extern void gio_dev_put(struct gio_device *);

--- a/arch/mips/include/asm/hazards.h
+++ b/arch/mips/include/asm/hazards.h
@@ -23,7 +23,7 @@
 * TLB hazards
 */
 #if (defined(CONFIG_CPU_MIPSR2) || defined(CONFIG_CPU_MIPSR6)) && \
-	!defined(CONFIG_CPU_CAVIUM_OCTEON) && !defined(CONFIG_LOONGSON3_ENHANCEMENT)
+	!defined(CONFIG_CPU_CAVIUM_OCTEON) && !defined(CONFIG_CPU_LOONGSON64)

 /*
 * MIPSR2 defines ehb for hazard avoidance
@@ -158,7 +158,7 @@ do {									\
 } while (0)

 #elif defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_CPU_CAVIUM_OCTEON) || \
-	defined(CONFIG_CPU_LOONGSON2EF) || defined(CONFIG_LOONGSON3_ENHANCEMENT) || \
+	defined(CONFIG_CPU_LOONGSON2EF) || defined(CONFIG_CPU_LOONGSON64) || \
 	defined(CONFIG_CPU_R10000) || defined(CONFIG_CPU_R5500) || defined(CONFIG_CPU_XLR)

 /*
--- a/Show More
+++ b/Show More