Pull HSI (High Speed Synchronous Serial Interface) framework from Carlos Chinea:
"The High Speed Synchronous Serial Interface (HSI) is a serial
interface mainly used for connecting application engines (APE) with
cellular modem engines (CMT) in cellular handsets.
The framework is currently being used for some people and we would
like to see it integrated into the kernel for 3.3. There is no HW
controller drivers in this pull, but some people have already some of
them pending which they would like to push as soon as this integrated.
I am also working on the acceptance for an TI OMAP one, based on a
compatible legacy version of the interface called SSI."
Ok, so it didn't get into 3.3, but here it is pulled into 3.4.
Several people piped up to say "yeah, we want this".
* 'for-next' of git://gitorious.org/kernel-hsi/kernel-hsi:
HSI: hsi_char: Update ioctl-number.txt
HSI: Add HSI API documentation
HSI: hsi_char: Add HSI char device kernel configuration
HSI: hsi_char: Add HSI char device driver
HSI: hsi: Introducing HSI framework
Pull media updates from Mauro Carvalho Chehab:
- V4L2 API additions to better support JPEG compression control
- media API additions to properly support MPEG decoders
- V4L2 API additions for image crop/scaling
- a few other V4L2 API DocBook fixes/improvements
- two new DVB frontend drivers: m88rs2000 and rtl2830
- two new DVB drivers: az6007 and rtl28xxu
- a framework for ISA drivers, that removed lots of common code found
at the ISA radio drivers
- a new FM transmitter driver (radio-keene)
- a GPIO-based IR receiver driver
- a new sensor driver: mt9m032
- some new video drivers: adv7183, blackfin, mx2_emmaprp, sii9234_drv,
vs6624
- several new board additions, driver fixes, improvements and cleanups.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (295 commits)
[media] update CARDLIST.em28xx
[media] partially reverts changeset fa5527c
[media] stb0899: fix the limits for signal strength values
[media] em28xx: support for 2304:0242 PCTV QuatroStick (510e)
[media] em28xx: support for 2013:0251 PCTV QuatroStick nano (520e)
[media] -EINVAL -> -ENOTTY
[media] gspca - sn9c20x: Cleanup source
[media] gspca - sn9c20x: Simplify register write for capture start/stop
[media] gspca - sn9c20x: Add automatic JPEG compression mechanism
[media] gspca - sn9c20x: Greater delay in case of sensor no response
[media] gspca - sn9c20x: Optimize the code of write sequences
[media] gspca - sn9c20x: Add the JPEG compression quality control
[media] gspca - sn9c20x: Add a delay after Omnivision sensor reset
[media] gspca - sn9c20x: Propagate USB errors to higher level
[media] gspca - sn9c20x: Use the new video control mechanism
[media] gspca - sn9c20x: Fix loss of frame start
[media] gspca - zc3xx: Lack of register 08 value for sensor cs2102k
[media] gspca - ov534_9: Add brightness to OmniVision 5621 sensor
[media] gspca - zc3xx: Add V4L2_CID_JPEG_COMPRESSION_QUALITY control support
[media] pvrusb2: fix 7MHz & 8MHz DVB-T tuner support for HVR1900 rev D1F5
...
Pull KGDB/KDB updates from Jason Wessel:
"Fixes:
- Fix KDB keyboard repeat scan codes and leaked keyboard events
- Fix kernel crash with kdb_printf() for users who compile new
kdb_printf()'s in early code
- Return all segment registers to gdb on x86_64
Features:
- KDB/KGDB hook the reboot notifier and end user can control if it
stops, detaches or does nothing (updated docs as well)
- Notify users who use CONFIG_DEBUG_RODATA to use hw breakpoints"
* tag 'for_linus-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
kdb: Add message about CONFIG_DEBUG_RODATA on failure to install breakpoint
kdb: Avoid using dbg_io_ops until it is initialized
kgdb,debug_core: add the ability to control the reboot notifier
KDB: Fix usability issues relating to the 'enter' key.
kgdb,debug-core,gdbstub: Hook the reboot notifier for debugger detach
kgdb: Respect that flush op is optional
kgdb: x86: Return all segment registers also in 64-bit mode
Sometimes it is desirable to stop the kernel debugger before allowing
a system to reboot either with kdb or kgdb. This patch adds the
ability to turn the reboot notifier on and off or enter the debugger
and stop kernel execution before rebooting.
It is possible to change the setting after booting the kernel with the
following:
echo 1 > /sys/module/debug_core/parameters/kgdbreboot
It is also possible to change this setting using kdb / kgdb to
manipulate the variable directly.
Using KDB:
mm kgdbreboot 1
Using gdb:
set kgdbreboot=1
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Pull trivial tree from Jiri Kosina:
"It's indeed trivial -- mostly documentation updates and a bunch of
typo fixes from Masanari.
There are also several linux/version.h include removals from Jesper."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
kcore: fix spelling in read_kcore() comment
constify struct pci_dev * in obvious cases
Revert "char: Fix typo in viotape.c"
init: fix wording error in mm_init comment
usb: gadget: Kconfig: fix typo for 'different'
Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
writeback: fix typo in the writeback_control comment
Documentation: Fix multiple typo in Documentation
tpm_tis: fix tis_lock with respect to RCU
Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
Doc: Update numastat.txt
qla4xxx: Add missing spaces to error messages
compiler.h: Fix typo
security: struct security_operations kerneldoc fix
Documentation: broken URL in libata.tmpl
Documentation: broken URL in filesystems.tmpl
mtd: simplify return logic in do_map_probe()
mm: fix comment typo of truncate_inode_pages_range
power: bq27x00: Fix typos in comment
...
Make the VIDIOC_G/S_SELECTION ioctls documentation more consistent
with the rest of media Docbook, use capital letters where necessary
and correct few minor errors.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.3': (1646 commits)
Linux 3.3
Don't limit non-nested epoll paths
netfilter: ctnetlink: fix race between delete and timeout expiration
ipv6: Don't dev_hold(dev) in ip6_mc_find_dev_rcu.
nilfs2: fix NULL pointer dereference in nilfs_load_super_block()
nilfs2: clamp ns_r_segments_percentage to [1, 99]
afs: Remote abort can cause BUG in rxrpc code
afs: Read of file returns EBADMSG
C6X: remove dead code from entry.S
wimax/i2400m: fix erroneous NETDEV_TX_BUSY use
net/hyperv: fix erroneous NETDEV_TX_BUSY use
net/usbnet: reserve headroom on rx skbs
bnx2x: fix memory leak in bnx2x_init_firmware()
bnx2x: fix a crash on corrupt firmware file
sch_sfq: revert dont put new flow at the end of flows
ipv6: fix icmp6_dst_alloc()
MAINTAINERS: Add Serge as maintainer of capabilities
drivers/video/backlight/s6e63m0.c: fix corruption storing gamma mode
MAINTAINERS: add entry for exynos mipi display drivers
MAINTAINERS: fix link to Gustavo Padovans tree
...
This is a small extension to the S_HW_FREQ_SEEK ioctl: if the wrap_around
value is not support by the hardware, then -EINVAL is returned.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Here is a small patch which fixes a DocBook mistake in the decoder_cmd
documentation.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The text for version 1.1 of the Open Sofware license doesn't seem
to be available anywhere on http://www.opensource.org/ any more.
Replace it with an URL on fedora.org.
Thanks to Randy Dunlap for his advise choosing the most
appropriate replacement URL.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix broken link in Documentation/filesystem, replacing
ftp://ftp.uk.linux.org/pub/linux/sct/fs/jfs/journal-design.ps.gz
by a URL on http://kernel.org
Thanks to Randy Dunlap for his advise on the best replacement
URL to use.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To track authenticated state seems to have been
a design mistake in cfg80211. It is possible to
have out of band authentication (FT), tracking
multiple authentications caused more problems
than it ever helped, and the implementation in
mac80211 is too complex.
Remove all this complexity, and let userspace
do whatever it wants to, mac80211 can deal with
that just fine. Association is still tracked of
course, but authentication no longer is. Local
auth state changes are thus no longer of value,
so ignore them completely.
This will also help implement SAE -- asking the
driver to do an authentication is now almost
equivalent to sending an authentication frame,
with the exception of shared key authentication
which is still handled completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix 2 fatal errors in the device-drivers docbook.
Also add some missing files from drivers/base/; since several
of these are DMA-related, add a section for DMA Management.
docproc: drivers/base/sys.c: No such file or directory
docproc: drivers/tty/serial/8250.c: No such file or directory
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If V4L2_CAP_DEVICE_CAPS is set, then the new device_caps field is filled with
the capabilities of the opened device node.
The capabilities field traditionally contains the capabilities of the physical
device, being a superset of all capabilities available at the several device
nodes. E.g., if you open /dev/video0, then if it contains VBI caps then that means
that there is a corresponding vbi node as well. And the capabilities field of
both the video and vbi nodes should contain identical caps.
However, it would be very useful to also have a capabilities field that contains
just the caps for the currently open device, hence the new CAP bit and field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix warning since kernel scheduler functions and kernel-doc
notation were moved to other files.
docproc: lnx-33-rc1/kernel/sched.c: No such file or directory
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix warning since kernel-doc comments were moved to another
source file.
Warning(lib/iomap.c): no structured comments found
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix new kernel-doc warning. This file no longer contains
kernel-doc comments.
Warning(include/linux/serial_core.h): no structured comments found
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (57 commits)
[media] as3645a: Fix compilation by including slab.h
[media] s5p-fimc: Remove linux/version.h include from fimc-mdevice.c
[media] s5p-mfc: Remove linux/version.h include from s5p_mfc.c
[media] ds3000: using logical && instead of bitwise &
[media] v4l2-ctrls: make control names consistent
[media] DVB: dib0700, add support for Nova-TD LEDs
[media] DVB: dib0700, add corrected Nova-TD frontend_attach
[media] DVB: dib0700, separate stk7070pd initialization
[media] DVB: dib0700, move Nova-TD Stick to a separate set
[media] : add MODULE_FIRMWARE to dib0700
[media] DVB-CORE: remove superfluous DTV_CMDs
[media] s5p-jpeg: adapt to recent videobuf2 changes
[media] s5p-g2d: fixed a bug in controls setting function
[media] s5p-mfc: Fix volatile controls setup
[media] drivers/media/video/s5p-mfc/s5p_mfc.c: adjust double test
[media] drivers/media/video/s5p-fimc/fimc-capture.c: adjust double test
[media] s5p-fimc: Fix incorrect control ID assignment
[media] dvb_frontend: Don't call get_frontend() if idle
[media] DocBook/dvbproperty.xml: Remove DTV_MODULATION from ISDB-T
[media] DocBook/dvbproperty.xml: Fix ISDB-T delivery system parameters
...
On ISDB-T, each layer can have its own independent modulation,
applied to the carriers that belong to the segments associated
with them. So, there's no sense to define a global modulation
parameter.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
