Pull KGDB/KDB regression fixes from Jason Wessel:
- Fix a Smatch warning that appeared in the 3.4 merge window
- Fix kgdb test suite with SMP for all archs without HW single stepping
- Fix kgdb sw breakpoints with CONFIG_DEBUG_RODATA=y limitations on x86
- Fix oops on kgdb test suite with CONFIG_DEBUG_RODATA
- Fix kgdb test suite with SMP for all archs with HW single stepping
* tag 'for_linus-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
x86,kgdb: Fix DEBUG_RODATA limitation using text_poke()
kgdb,debug_core: pass the breakpoint struct instead of address and memory
kgdbts: (2 of 2) fix single step awareness to work correctly with SMP
kgdbts: (1 of 2) fix single step awareness to work correctly with SMP
kgdbts: Fix kernel oops with CONFIG_DEBUG_RODATA
kdb: Fix smatch warning on dbg_io_ops->is_console
The Smatch tool warned that the change from commit b8adde8dd
(kdb: Avoid using dbg_io_ops until it is initialized) should
add another null check later in the kdb_printf().
It is worth noting that the second use of dbg_io_ops->is_console
is protected by the KDB_PAGER state variable which would only
get set when kdb is fully active and initialized. If we
ever encounter changes or defects in the KDB_PAGER state
we do not want to crash the kernel in a kdb_printf/printk.
CC: Tim Bird <tim.bird@am.sony.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Pull KGDB/KDB updates from Jason Wessel:
"Fixes:
- Fix KDB keyboard repeat scan codes and leaked keyboard events
- Fix kernel crash with kdb_printf() for users who compile new
kdb_printf()'s in early code
- Return all segment registers to gdb on x86_64
Features:
- KDB/KGDB hook the reboot notifier and end user can control if it
stops, detaches or does nothing (updated docs as well)
- Notify users who use CONFIG_DEBUG_RODATA to use hw breakpoints"
* tag 'for_linus-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
kdb: Add message about CONFIG_DEBUG_RODATA on failure to install breakpoint
kdb: Avoid using dbg_io_ops until it is initialized
kgdb,debug_core: add the ability to control the reboot notifier
KDB: Fix usability issues relating to the 'enter' key.
kgdb,debug-core,gdbstub: Hook the reboot notifier for debugger detach
kgdb: Respect that flush op is optional
kgdb: x86: Return all segment registers also in 64-bit mode
On x86, if CONFIG_DEBUG_RODATA is set, one cannot set breakpoints
via KDB. Apparently this is a well-known problem, as at least one distribution
now ships with both KDB enabled and CONFIG_DEBUG_RODATA=y for security reasons.
This patch adds an printk message to the breakpoint failure case,
in order to provide suggestions about how to use the debugger.
Reported-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Tim Bird <tim.bird@am.sony.com>
This fixes a bug with setting a breakpoint during kdb initialization
(from kdb_cmds). Any call to kdb_printf() before the initialization
of the kgdboc serial console driver (which happens much later during
bootup than kdb_init), results in kernel panic due to the use of
dbg_io_ops before it is initialized.
Signed-off-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
This fixes the following problems:
1) Typematic-repeat of 'enter' gives warning message
and leaks make/break if KDB exits. Repeats
look something like 0x1c 0x1c .... 0x9c
2) Use of 'keypad enter' gives warning message and
leaks the ENTER break/make code out if KDB exits.
KP ENTER repeats look someting like 0xe0 0x1c
0xe0 0x1c ... 0xe0 0x9c.
3) Lag on the order of seconds between "break" and "make" when
expecting the enter "break" code. Seen under virtualized
environments such as VMware ESX.
The existing special enter handler tries to glob the enter break code,
but this fails if the other (KP) enter was used, or if there was a key
repeat. It also fails if you mashed some keys along with enter, and
you ended up with a non-enter make or non-enter break code coming
after the enter make code. So first, we modify the handler to handle
these cases. But performing these actions on every enter is annoying
since now you can't hold ENTER down to scroll <more>d messages in
KDB. Since this special behaviour is only necessary to handle the
exiting KDB ('g' + ENTER) without leaking scancodes to the OS. This
cleanup needs to get executed anytime the kdb_main loop exits.
Tested on QEMU. Set a bp on atkbd.c to verify no scan code was leaked.
Cc: Andrei Warkentin <andreiw@vmware.com>
[jason.wessel@windriver.com: move cleanup calls to kdb_main.c]
Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
module_ref contains two "unsigned int" fields.
Thats now too small, since some machines can open more than 2^32 files.
Check commit 518de9b39e (fs: allow for more than 2^31 files) for
reference.
We can add an aligned(2 * sizeof(unsigned long)) attribute to force
alloc_percpu() allocating module_ref areas in single cache lines.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Tejun Heo <tj@kernel.org>
CC: Robin Holt <holt@sgi.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
These files were getting <linux/module.h> via an implicit non-obvious
path, but we want to crush those out of existence since they cost
time during compiles of processing thousands of lines of headers
for no reason. Give them the lightweight header that just contains
the EXPORT_SYMBOL infrastructure.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The first packet that gdb sends when the kernel is in kdb mode seems
to change with every release of gdb. Instead of continuing to add
many different gdb packets, change kdb to automatically look for any
thing that looks like a gdb packet.
Example 1 cold start test:
echo g > /proc/sysrq-trigger
$D#44+
Example 2 cold start test:
echo g > /proc/sysrq-trigger
$3#33
The second one should re-enter kdb's shell right away and is purely a
test.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
The DOING_KGDB2 was originally a state variable for one of the two
ways to automatically transition from kdb to kgdb. Purge all these
variables and just use one single state for the transition.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
When switching from kdb mode to kgdb mode packets were getting lost
depending on the size of the fifo queue of the serial chip. When gdb
initially connects if it is in kdb mode it should entirely send any
character buffer over to the gdbstub when switching connections.
Previously kdb was zero'ing out the character buffer and this could
lead to gdb failing to connect at all, or a lengthy pause could occur
on the initial connect.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
The BTARGS and BTSYMARG variables do not have any function in the
mainline version of kdb.
Reported-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
When the number of dyanmic kdb commands exceeds KDB_BASE_CMD_MAX, the
kernel will fault.
Signed-off-by: Jovi Zhang <bookjovi@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
The kdb_current legally be equal to NULL in the early boot of the x86
arch. The problem pcan be observed by booting with the kernel arguments:
earlyprintk=vga ekgdboc=kbd kgdbwait
The kdb shell will oops on entry and recursively fault because it
cannot get past the final stage of shell initialization.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Rusty pointed out that the per_cpu command uses up lots of space on
the stack and the cpu supress mask is probably not needed.
This patch removes the need for the supress mask as well as fixing up
the following problems with the kdb per_cpu command:
* The per_cpu command should allow an address as an argument
* When you have more data than can be displayed on one screen allow
the user to break out of the print loop.
Reported-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
